An official website of the United States government
After a wildfire event, ash is a newly formed surficial soil layer with microscale properties such as roughness, morphology, and chemical composition that may impact how ashes form fabrics in situ and so affect the overall hydrological conditions of a burned area (infiltration capacity, permeability, etc.). To examine the effects of ash microscale properties on macroscale behavior, eight wildfire ash samples from California were characterized physically (specific gravity, specific surface area, particle size, etc.), chemically (elemental composition, organic and inorganic carbon content, etc.), and geotechnically (strength, compaction, saturated hydraulic conductivity, etc.). The tested ashes were found to contain predominantly organic unburned carbons and carbonates derived from the combustion of calcium-oxalate rich fuels in temperatures likely ranging from 300°C to 500°C. Ashes had high specific surface areas because morphologically, particles had highly texturized and porous surfaces. Additional water was necessary to coat the particle surfaces, which led to high liquid limits and compaction optimum moisture contents. Hydraulic conductivity values were within range for silty sands (10^−5–10^−3 cm/s), and specimens had friction angles near 30°. However, tested ashes consistently demonstrated high void ratios and low bulk densities during testing for strength, hydraulic conductivity, and compaction. These anomalies were attributed to unusual carbonate morphologies; the high interparticle friction of these phases allowed ashes to form looser fabrics than a typical silty sand and contributed to the measured high void ratios, low maximum dry unit weights, and high friction angles. Overall, we hypothesize that the relative amounts of inorganic versus organic constituents in our wildfire ash samples affected how the ashes formed fabrics and so affected their geotechnical properties.
more »
« less
Engineering properties of wildfire ashes
While a large amount of research has been performed in recent years on characterizing wildfire ashes and determining the hydrological properties of slopes post-wildfire, fewer studies have concentrated on the overall engineering behavior of ash. This study addresses this need by examining the compaction, shear strength, and hydraulic behavior of wildfire ash and ash/soil layered specimens. Unique chemical and physical characteristics of wildfire ashes were shown to influence the ash engineering behavior. Ashes in the as-received condition have a silty sand grain size distribution with higher than expected surface areas (>1 m2/g). Chemically, ashes contained silica, aluminum, calcium (in the form of carbonates) and residual organic carbon from incomplete combustion. Maximum dry unit weights ranged from 13 – 16 kN/m3 at optimum moisture contents between 20 and 30%. Hydraulic conductivity of samples varied between 10^-4 and 10^-5 cm/s. A wet deposited layer of fine-grained ash on top of compacted sand reduced the hydraulic conductivity of sand by 1 – 3 orders of magnitude. Shear strength of ash/sand layered specimens demonstrated that ash was fairly stiff, with an average friction angle of 28 degrees. Void ratios of specimens were consistently higher than expected for a silty sand fabric (usually above 1.0). Ash particles were irregular in shape with fibrous textures and had electrostatic attractive tendencies. The authors suspect that the unique chemistries present in ash (notably carbonates and organic char) contributed to the loose fabric structure and engineering properties that were atypical of a silty sand grain size distribution
more »
« less
- Award ID(s):
- 2138449
- PAR ID:
- 10523548
- Publisher / Repository:
- Proceedings of the 9ICEG
- Date Published:
- Subject(s) / Keyword(s):
- wildfire ash compaction shear strength characterization carbonates
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The reliance on sand-based methods for the characterization and design of gravelly soils is necessitated in part by a limited understanding of how to account for the effects of particle size and distribution. In this paper, particle size effects on the strength and fabric of cohesionless, granular media are investigated using the discrete element method by testing specimens with particle size distributions (PSDs) of differing coefficient of uniformity (CU) and mean grain size (d50). Preliminary results show that when all particle shape characteristics are equal, increasing d50 yields equivalent stress-strain responses for the same relative density (DR) and CU. However, when increasing CU, specimens exhibit more dilative tendencies and greater shear strengths. Increasing CU results in more dispersive distributions of contact force, stress, and coordination number. The void ratios associated with minimum and maximum density, and constant volume conditions during shear also decrease with increasing CU.more » « less
-
Wildfire ash and water-repellent soil are new materials that are formed after a wildfire that change the mechanical and hydraulic behavior of wildfire-burned slopes. Wildfire ash is known to be typically hydrophilic and to retain water, whereas the water-repellent soil layer acts as a hydraulic barrier. However, there is limited in situ soil water content data to understand the short- and long-term impacts of wildfire ash and a water-repellent soil layer on the hydromechanical behavior of burned slopes. This study investigates the trends in water content of wildfire ash, water-repellent soil, and subsurface soil after the 2022 Bolt Creek Wildfire near Skykomish, WA. The ash deposit averaged 10 cm, with a maximum 30 cm thickness in channels immediately after the fire, which allowed the in situ measurement of ash water content. Soil water content sensors were installed in the ash and subsurface soil layers, and changes in the water content were monitored for a year after the fire. The surface ash layer was above a thin (<1 cm) water-repellent soil layer, which was followed by the soil that did not show any apparent effects from the fire. The results showed a reduction in ash thickness and the persistence of the water-repellent layer over a year.more » « less
-
Extensive research has been reported in the literature to characterize the failure mode of dry sand using various experimental techniques such as surface optical imaging, photo-elastic materials, 3D computed tomography (CT), and 3D synchrotron micro-computed tomogra-phy (SMT). However, there is a limited literature about the behavior of saturated sand. This paper presents the results of axisymmetric triaxial compression (ATC) experiments that were conducted on saturated sand specimens. The behavior of specimens composed of a uniform sand with grain size between US sieves #40 and #50 is compared to specimens conducted on the same sand that has a wider gradation. 3D SMT technique was used to acquire 3D scans while shearing the spec-imens to probe localized events that are completely missed or misinterpreted when analyzing ATC measurements based on global standard measurements. The results show a higher EPSR for the non-uniform specimen and a thicker shear band when compared to uniform specimen.more » « less
-
Natural soil deposits can consist of particles with a wide range of sizes. In current practice, the assessment of shear strength and stress-dilatancy behavior of coarse-grained soils is based on methods developed for poorly graded sands, without explicit consideration for differences in gradation. This paper investigates the influence of the range of particle sizes on the monotonic shear strength and the stress-dilatancy response of poorly- to well-graded soils. Using the 3D discrete element method (DEM), the applicability of commonly used sand-based stress-dilatancy frameworks is assessed for a range of gradations. This DEM investigation employs clumps of spheres to accurately simulate the particle shapes on specimens with coefficients of uniformity (CU) varying between 1.9 and 6.9. These specimens were subjected to isotropically consolidated drained triaxial compression at various relative densities and confining stresses with the objective of isolating the effects of particle size distribution from those of particle shape. The peak and critical state shear strengths and the dilatancy responses of the specimens with different gradations are evaluated. For the same state parameter, the results indicate an increase in the shear strength and rate of dilation as the range of particle sizes increases. However, the critical state line shifts downward, and its slope decreases as CU is increased. The DEM results are compared to Bolton’s stress-dilatancy relationship to highlight the inadequacies of using clean sand-based frameworks in capturing the behavior of well-graded soils.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Proceeding:
- The DOI is not currently available.
