Viscosity is a fundamental physical property of lava that dictates style and rate of effusive transport. Studies of lava viscosity have predominantly focused on measuring re-melted rocks in the laboratory. While these measurements are well-constrained in temperature, shear rate, and oxygen fugacity, they cannot reproduce the complexities of the natural emplacement environment. Field viscosity measurements of active lava are the only way to fully capture lava’s properties, but such measurements are scarce, largely due to a lack of easy-to-use, portable, and accurate measurement devices. Thus, there is a need for developing suitable field instruments to help bolster the understanding of lava. Here, we present a new penetrometer capable of measuring a material’s viscosity under the harsh conditions of natural lava emplacement. This device uses a stainless-steel tube with a semi-spherical tip fixed to a load cell that records axial force when pushed into a material, while simultaneously measuring the penetration depth via a free-moving tube that is pushed backward along the penetration tube. The device is portable (1.5 m long, 5.5 kg in weight) and uses a single-board computer for data acquisition. The penetrometer has an operational range from 2.5 × 102 to 2.1 × 105 Pa s and was calibrated for viscosities ranging from 5.0 × 102 to 1.6 × 105 Pa s. It was deployed to the 2023 Litli-Hrútur eruption in Iceland. These field measurements successfully recorded the in situ viscosities of the lava in the range of 1.2 × 104–3.4 × 104 Pa s, showcasing it as an efficient method of measuring natural lava viscosity.
more »
« less
This content will become publicly available on October 1, 2024
A new portable field rotational viscometer for high-temperature melts
Mounted on top of furnaces, laboratory viscometers can be used for the rheological characterization of high temperature melts, such as molten rocks (lava). However, there are no instruments capable of measuring the viscosity of large volumes of high temperature melts outside the laboratory at, for example, active lava flows on volcanoes or at industrial sites. In this article, we describe a new instrument designed to be easy to operate, highly mobile, and capable of measuring the viscosity of high temperature liquids and suspensions (<1350 °C). The device consists of a torque sensor mounted in line with a stainless-steel shear vane that is immersed in the melt and driven by a motor that rotates the shear vane. In addition, a thermocouple placed between the blades of the shear vane measures the temperature of the melt at the measurement location. An onboard microcomputer records torque, rotation rate, and temperature simultaneously and in real time, thus enabling the characterization of the rheological flow curve of the material as a function of temperature and strain rate. The instrument is calibrated using viscosity standards at low temperatures (20–60 °C) and over a wide range of stress (30–3870 Pa), strain rate (0.1–27.9 s−1), and viscosity (10–650 Pa s). High temperature tests were performed in large scale experiments within ∼25 l of lava at temperatures between 1000 and 1350 °C to validate the system’s performance for future use in natural lava flows. This portable field viscometer was primarily designed to measure the viscosity of geological melts at their relevant temperatures and in their natural state on the flanks of volcanoes, but it could also be used for industrial purposes and beyond.
more »
« less
- Award ID(s):
- 2241489
- NSF-PAR ID:
- 10529286
- Publisher / Repository:
- AIP Publishing
- Date Published:
- Journal Name:
- Review of Scientific Instruments
- Volume:
- 94
- Issue:
- 10
- ISSN:
- 0034-6748
- Subject(s) / Keyword(s):
- Analog-to-digital converter, Sensors, Thermocouples, Volcanology, Data acquisition, Data processing, Microcomputers, Rheological properties, Viscosity measurements
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Methylcellulose solutions are known to form microfibrils at elevated temperatures or in the presence of salt. The fibrils have a significant impact on the solution's rheological properties. Here, the shear and extensional properties of methylcellulose solutions with added salt are measured using hyperbolic microfluidic channels, allowing for new characterization at lower molecular weights and higher shear and strain rates that are difficult to access by macroscale rheology studies. 1 and 2 wt% methylcellulose solutions with molecular weight of 150 kg mol −1 with NaCl content between 0 to 5 wt% have been characterized. All solutions were found to be shear thinning, with power law thinning behavior at shear rates above 100 s −1 . The addition of NaCl up to 5 wt% had only small effects on shear viscosity at the shear rates probed (100 s −1 and 10 000 s −1 ). Extensional viscosities as low as 0.02 Pa s were also measured. Unlike the results for shear viscosity, the addition of 5 wt% NaCl caused significant changes in extensional viscosity, increasing by up to 10 times, depending on extension rate. Additionally, all solutions tested showed apparent extensional thinning in the high strain rate regime (>100 s −1 ), which has not been reported in other studies of methylcellulose solutions. These findings may provide insight for those using methylcellulose solutions in process designs involving extensional flows over a wide range of strain rates.more » « less
-
Understanding the viscosity of mantle-derived magmas is needed to model their migration mechanisms and ascent rate from the source rock to the surface. High pressure–temperature experimental data are now available on the viscosity of synthetic melts, pure carbonatitic to carbonate–silicate compositions, anhydrous basalts, dacites and rhyolites. However, the viscosity of volatile-bearing melilititic melts, among the most plausible carriers of deep carbon, has not been investigated. In this study, we experimentally determined the viscosity of synthetic liquids with ~31 and ~39 wt% SiO2, 1.60 and 1.42 wt% CO2 and 5.7 and 1 wt% H2O, respectively, at pressures from 1 to 4.7 GPa and temperatures between 1265 and 1755 °C, using the falling-sphere technique combined with in situ X-ray radiography. Our results show viscosities between 0.1044 and 2.1221 Pa·s, with a clear dependence on temperature and SiO2 content. The atomic structure of both melt compositions was also determined at high pressure and temperature, using in situ multi-angle energy-dispersive X-ray diffraction supported by ex situ microFTIR and microRaman spectroscopic measurements. Our results yield evidence that the T–T and T–O (T = Si,Al) interatomic distances of ultrabasic melts are higher than those for basaltic melts known from similar recent studies. Based on our experimental data, melilititic melts are expected to migrate at a rate ~from 2 to 57 km·yr−1 in the present-day or the Archaean mantle, respectively.more » « less
-
Material relationships at low temperatures were determined for concentrated surfactant solutions using a combination of rheological experiments, cross-polarized microscopy, calorimetry, and small angle X-ray scattering. A lamellar structured 70 wt% solution of sodium laureth sulfate in water was used as a model system. At cold temperatures (5 °C and 10 °C), the formation of surfactant crystals resulted in extremely high viscosity. The bulk flow behavior of multi-lamellar vesicles (20 °C) and focal conic defects (90 °C) in the lamellar phase was similar. Shear-induced crystallization at temperatures higher than the equilibrium crystallization temperature range resulted in an unusual complex viscosity peak. The effects of processing-relevant parameters including temperature, cooling time, and applied shear were investigated. Knowledge of key low-temperature structure–property-processing relationships for concentrated feedstocks is essential for the sustainable design and manufacturing of surfactant-based consumer products for applications such as cold-water laundry.more » « less
-
more » « less
Abstract Novel fluid medium pressure cells were used to deform antigorite under constant stress creep conditions at low temperature, low strain rate (10−9 − 10−41/s), and high pressure (1 GPa) in a Griggs‐type apparatus. Antigorite cores were deformed at constant temperatures between 75°C and 550°C, by applying 8–12 stress‐strain steps per temperature. The microstructures of deformed samples share features documented in previous work (e.g., shear microcracks), and highlight the importance of basal shear and kinks to antigorite plasticity. Rheological data were fit with a low temperature plasticity law, consistent with a deformation mechanism involving large lattice resistance. When applied at geologic stresses and strain rates, the extrapolated viscosity agrees well with predictions based on subduction zone thermal models.
