An official website of the United States government
Abstract The far-from-equilibrium solidification during additive manufacturing often creates large residual stresses that induce solid-state cracking. Here we present a strategy to suppress solid-state cracking in an additively manufactured AlCrFe2Ni2high-entropy alloy via engineering phase transformation pathway. We investigate the solidification microstructures formed during laser powder-bed fusion and directed energy deposition, encompassing a broad range of cooling rates. At high cooling rates (104−106 K/s), we observe a single-phase BCC/B2 microstructure that is susceptible to solid-state cracking. At low cooling rates (102−104 K/s), FCC phase precipitates out from the BCC/B2 matrix, resulting in enhanced ductility (~10 %) and resistance to solid-state cracking. Site-specific residual stress/strain analysis reveals that the ductile FCC phase can largely accommodate residual stresses, a feature which helps relieve residual strains within the BCC/B2 phase to prevent cracking. Our work underscores the value of exploiting the toolbox of phase transformation pathway engineering for material design during additive manufacturing.
more »
« less
Ubiquitous short-range order in multi-principal element alloys
Abstract Recent research in multi-principal element alloys (MPEAs) has increasingly focused on the role of short-range order (SRO) on material performance. However, the mechanisms of SRO formation and its precise control remain elusive, limiting the progress of SRO engineering. Here, leveraging advanced additive manufacturing techniques that produce samples with a wide range of cooling rates (up to 107 K s−1) and an enhanced semi-quantitative electron microscopy method, we characterize SRO in three CoCrNi-based face-centered-cubic (FCC) MPEAs. Surprisingly, irrespective of the processing and thermal treatment history, all samples exhibit similar levels of SRO. Atomistic simulations reveal that during solidification, prevalent local chemical order arises in the liquid-solid interface (solidification front) even under the extreme cooling rate of 1011 K s−1. This phenomenon stems from the swift atomic diffusion in the supercooled liquid, which matches or even surpasses the rate of solidification. Therefore, SRO is an inherent characteristic of most FCC MPEAs, insensitive to variations in cooling rates and even annealing treatments typically available in experiments.
more »
« less
- PAR ID:
- 10529487
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Nature Communications
- Volume:
- 15
- Issue:
- 1
- ISSN:
- 2041-1723
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Investigating the conditions behind the formation of pyroclast textures and lava flow morphologies is important to understand the dynamics of submarine volcanic eruptions, which are hard to observe. The development of clast textures and lava morphologies depends on the competing effects of their eruption rates and the rates of solidification. While eruption rates are governed by subsurface magmatic processes, the solidification timescales depend on the rate of heat loss from lava to the external water. However, the effect of the speed of lava flow or clast on their solidification timescales under two‐phase (liquid water and vapor bubbles) water boiling conditions is poorly constrained. Using laboratory experiments with remelted igneous rocks, we investigate the effect of the relative motion between lava and external water on its cooling timescale. We use a range of water speed (0–12.5 cm s−1) in our experiments while keeping our sample stationary to simulate a range of relative speed between lava and ambient water. Using transient heat transfer modeling, we find that heat flux from the surface of the sample to the external water overall increases with increasing water speed. We find heat transfer coefficients of up to ∼1.72 × 103 W m−2 K−1. The implications of high heat flux on the formation of solid lava crust under submarine conditions are discussed.more » « less
-
Abstract Non‐volatile phase‐change memory (PCM) devices are based on phase‐change materials such as Ge2Sb2Te5 (GST). PCM requires critically high crystallization growth velocity (CGV) for nanosecond switching speeds, which makes its material‐level kinetics investigation inaccessible for most characterization methods and remains ambiguous. In this work, nanocalorimetry enters this “no‐man's land” with scanning rate up to 1 000 000 K s−1(fastest heating rate among all reported calorimetric studies on GST) and smaller sample‐size (10–40 nm thick) typical of PCM devices. Viscosity of supercooled liquid GST (inferred from the crystallization kinetic) exhibits Arrhenius behavior up to 290 °C, indicating its low fragility nature and thus a fragile‐to‐strong crossover at ≈410 °C. Thin‐film GST crystallization is found to be a single‐step Arrhenius process dominated by growth of interfacial nuclei with activation energy of 2.36 ± 0.14 eV. Calculated CGV is consistent with that of actual PCM cells. This addresses a 10‐year‐debate originated from the unexpected non‐Arrhenius kinetics measured by commercialized chip‐based calorimetry, which reports CGV 103−105higher than those measured using PCM cells. Negligible thermal lag (<1.5 K) and no delamination is observed in this work. Melting, solidification, and specific heat of GST are also measured and agree with conventional calorimetry of bulk samples.more » « less
-
Multi-principal-element alloys (MPEAs) based on 3d-transition metals show remarkable mechanical properties. The stacking fault energy (SFE) in face-centered cubic (fcc) alloys is a critical property that controls underlying deformation mechanisms and mechanical response. Here, we present an exhaustive density-functional theory study on refractory- and copper-reinforced Cantor-based systems to ascertain the effects of refractory metal chemistry on SFE. We find that even a small percent change in refractory metal composition significantly changes SFEs, which correlates favorably with features like electronegativity variance, size effect, and heat of fusion. For fcc MPEAs, we also detail the changes in mechanical properties, such as bulk, Young’s, and shear moduli, as well as yield strength. A Labusch-type solute-solution-strengthening model was used to evaluate the temperature-dependent yield strength, which, combined with SFE, provides a design guide for high-performance alloys. We also analyzed the electronic structures of two down-selected alloys to reveal the underlying origin of optimal SFE and strength range in refractory-reinforced fcc MPEAs. These new insights on tuning SFEs and modifying composition-structure-property correlation in refractory- and copper-reinforced MPEAs by chemical disorder, provide a chemical route to tune twinning- and transformation-induced plasticity behavior.more » « less
-
Abstract High temperature synthesis and treatments are ubiquitous in chemical reactions and material manufacturing. However, conventional sintering furnaces are bulky and inefficient with a narrow temperature range (<1500 K) and slow heating rates (<100 K min−1), which are undesirable for many applications that require transient heating to produce ideal nanostructures. Herein, a 3D‐printed, miniaturized reactor featuring a dense micro‐grid design is developed to maximize the material contact and therefore acheive highly efficient and controllable heating. By 3D printing, a versatile, miniaturized reactor with microscale features can be constructed, which can reach a much wider temperature range (up to ≈3000 K) with ultrafast heating/cooling rates of ≈104K s−1. To demonstrate the utility of the design, rapid and batch synthesis of Ru nanoparticles supported in ordered mesoporous carbon is performed by transient heating (1500 K, 500 ms). The resulting ultrafine and uniform Ru nanoparticles (≈2 nm) can serve as a cathode in Li‐CO2batteries with good cycling stability. The miniaturized reactor, with versatile shape design and highly controllable heating capabilities, provides a platform for nanocatalyst synthesis with localized and ultrafast heating toward high temperatures that is otherwise challenging to achieve.more » « less
