An official website of the United States government
In this study, we demonstrate a tolerant and durable Cr/Ni bilayer metal etch mask that allows us to realize approximately 150:1 etch selectivity to diamond. This result is achieved through the use of a very thin initial Cr layer of <10 nm thickness as part of the bilayer metal mask, which results in five to ten times improved selectivity than thick single metal layer masks or bilayer masks with thicker combinations. A finite element analysis was employed to design and understand the physics and working mechanism of the bilayer metal masks with different thicknesses. Raman spectroscopy and energy-dispersive x-ray spectroscopy on the diamond surface were also performed to investigate the changes in diamond quality before and after the deep diamond etching and found that no noticeable etch damage or defects were formed. Overall, this mask strategy offers a viable way to realize deep diamond etching using a high heat and chemistry tolerant and durable bilayer metal etching mask. It also offers several technological benefits and advantages, including various deposition method options, such as sputtering and physical vapor deposition, that can be used and the total thinness of the bilayer metal mask required given the higher selectivity allows us to realize fine diamond etching or high-aspect ratio etching, which is a critical fabrication process for future power, RF, MEMS, and quantum device applications.
more »
« less
Development of hard masks for reactive ion beam angled etching of diamond
Diamond offers good optical properties and hosts bright color centers with long spin coherence times. Recent advances in angled-etching of diamond, specifically with reactive ion beam angled etching (RIBAE), have led to successful demonstration of quantum photonic devices operating at visible wavelengths. However, larger devices operating at telecommunication wavelengths have been difficult to fabricate due to the increased mask erosion, arising from the increased size of devices requiring longer etch times. We evaluated different mask materials for RIBAE of diamond photonic crystal nanobeams and waveguides, and how their thickness, selectivity, aspect ratio and sidewall smoothness affected the resultant etch profiles and optical performance. We found that a thick hydrogen silesquioxane (HSQ) layer on a thin alumina adhesion layer provided the best etch profile and optical performance. The techniques explored in this work can also be adapted to other bulk materials that are not available heteroepitaxially or as thin films-on-insulator.
more »
« less
- PAR ID:
- 10531216
- Publisher / Repository:
- Optical Society of America
- Date Published:
- Journal Name:
- Optics Express
- Volume:
- 30
- Issue:
- 9
- ISSN:
- 1094-4087; OPEXFF
- Format(s):
- Medium: X Size: Article No. 14189
- Size(s):
- Article No. 14189
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Low-loss silicon nitride Kerr-microresonators fabricated with metallic etch masks via metal lift-offStoichiometric silicon nitride has emerged as a widely used integrated photonic material owing to its high index of refraction, nonlinear optical properties, and broad transparency window spanning visible to mid-IR frequencies. However, silicon nitride is generally more resistant to reactive ion etching than are typical etch masks made of polymer-based resist. This necessitates resist layers that are significantly thicker than the silicon nitride and results in mask patterns which are tall and narrow. These high-aspect-ratio patterns inhibit the plasma transport of reactive ion etching, which leads to difficulties in accurately reproducing dimensions and creating well-defined, vertical waveguide sidewalls. In this work, we overcome these challenges by developing a metallic etch mask deposited via metal lift-off that provides a 30 : 1 nitride-to-metal etch rate ratio, representing a near 45-fold reduction in the required mask thickness. We demonstrate the validity of this technique by etching microring resonators with near-vertical waveguide sidewalls and intrinsic quality factors of over 1 million. Leveraging the low optical loss of our resonators, we generate optical frequency combs with more than an octave of bandwidth and dual dispersive waves. These results establish metal lift-off as a viable and easy-to-implement technique capable of producing low optical loss waveguides.more » « less
-
Lithium niobate (LiNbO3, LN) is a ferroelectric crystal of interest for integrated photonics owing to its large second-order optical nonlinearity and the ability to impart periodic poling via an external electric field. However, on-chip device performance based on thin-film lithium niobate (TFLN) is presently limited by propagation losses arising from surface roughness and corrugations. Atomic layer etching (ALE) could potentially smooth these features and thereby increase photonic performance, but no ALE process has been reported for LN. Here, we report an isotropic ALE process for x-cut MgO-doped LN using sequential exposures of H2 and SF6/Ar plasmas. We observe an etch rate of 1.59±0.02 nm/cycle with a synergy of 96.9%. We also demonstrate that ALE can be achieved with SF6/O2 or Cl2/BCl3 plasma exposures in place of the SF6/Ar plasma step with synergies of 99.5% and 91.5%, respectively. The process is found to decrease the sidewall surface roughness of TFLN waveguides etched by physical Ar+ milling by 30% without additional wet processing. Our ALE process could be used to smooth sidewall surfaces of TFLN waveguides as a postprocessing treatment, thereby increasing the performance of TFLN nanophotonic devices and enabling new integrated photonic device capabilities.more » « less
-
Although Sc doped AlN (ScAlN) has been used extensively in micro-electro-mechanical systems (MEMS) devices and more recently in optical devices, there have not been thorough studies of its intrinsic optical losses. Here we explore the optical losses of the Sc0.30Al0.70N waveguide system by observing racetrack resonator waveguide quality factors. Using a partial physical etch, we fabricate waveguides and extract propagation losses as low as 1.6 ± 0.3 dB/cm at wavelengths around 1550 nm, mostly dominated by intrinsic material absorption from the Sc0.30Al0.70N thin film layer. The highest quality factor of the resonators was greater than 87,000. The propagation loss value is lower than any value previously published and shows that this material can be broadly used in optical modulators without significant loss.more » « less
-
Robust, low-loss photonic packaging of on-chip nanophotonic circuits is a key enabling technology for the deployment of integrated photonics in a variety of classical and quantum technologies including optical communications and quantum communications, sensing, and transduction. To date, no process has been established that enables permanent, broadband, and cryogenically compatible coupling with sub-dB losses from optical fibers to nanophotonic circuits. Here, we report a technique for reproducibly generating a permanently packaged interface between a tapered optical fiber and nanophotonic devices on diamond with a record-low coupling loss <1 dB per facet at near-infrared wavelengths (∼730 nm) that remains stable from 300 K to 30 mK. We further demonstrate the compatibility of this technique with etched lithium niobate on insulator waveguides. The technique lifts performance limitations imposed by scattering as light transfers between photonic devices and optical fibers, paving the way for scalable integration of photonic technologies at both room and cryogenic temperatures.more » « less
