skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Upcycled PVC support layer from waste PVC pipe for thin film composite nanofiltration membranes
Thin-film-composite (TFC) nanofiltration membranes represent the pinnacle of membrane technology in water treatment and desalination. These membranes typically consist of a polyamide (PA) selective layer and a membrane support layer, often constructed from commercially available materials like polyethersulfone (PES). However, there exists an alternative approach that involves the use of different polymers, preferably upcycled waste polymers, as a viable support layer for TFC membranes. Successfully implementing the upcycling of waste plastics into high-value support membranes can make a significant contribution to addressing the issue of plastic waste pollution. One of the primary challenges associated with utilizing upcycled polymers as support layers is the potential impact on the polyamide selective layer of TFC membranes, subsequently affecting their performance in terms of permeability, rejection, and antifouling properties. In this study, we demonstrate the successful fabrication of TFC membranes with a support layer crafted from upcycled waste PVC pipe. We conducted a comprehensive investigation into the effects of upcycled PVC on the structural and physicochemical properties of the polyamide layer. The ultrafiltration (UF) support membranes were fabricated from waste PVC pipe via the nonsolvent induced phase separation (NIPS) method. Subsequently, a polyamide layer was synthesized atop the Upcycled PVC membrane using interfacial polymerization (IP). The physicochemical properties and performance of the TFC membranes with upcycled PVC support layer were compared with membranes with research-grade (RG) PVC and commercial PES support layers. The results unveiled that the TFC membrane with upcycled PVC support layer exhibited higher water permeability (18.2 LMH/bar), in contrast to RG TFC (15.5 LMH/bar) and PES TFC membranes (13.7 LMH/bar). Furthermore, the salt rejection capabilities of the upcycled PVC TFC membrane were competitive and well within an acceptable range.  more » « less
Award ID(s):
2029387
PAR ID:
10531401
Author(s) / Creator(s):
;
Editor(s):
Tarabra, V
Publisher / Repository:
Elsevier
Date Published:
Journal Name:
Separation and Purification Technology
Volume:
340
ISSN:
1383-5866
Page Range / eLocation ID:
126747
Subject(s) / Keyword(s):
Plastic pollution Plastic upcycling Filtration Clean environment Wastewater treatment
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; (, ACS Applied Engineering Materials)
    In recent decades, the increased use of polyvinyl chloride (PVC) in industries and households has led to a surge in PVC waste pollution, which mandates developing solutions for the removal of waste PVC from the environment. We report upcycling, the conversion of waste material to a high-value-added product, of PVC-based products to electrospun (ES) fibers (mats). As two common PVC products, waste PVC pipe and waste PVC pool float were upcycled to ES fibers for water treatment. The fabrication process and fiber characteristics, such as morphology, surface charge, and mechanical strength of upcycled fibers, were studied and compared with the same fibers fabricated using research-grade (RG) PVC (commercial PVC powder). In addition, the effect of additives such as calcium carbonate in PVC waste products on the physicochemical properties of upcycled fibers was evaluated. The results showed that upcycling of waste PVC to ES fibers is feasible since the upcycled fibers showed similar or superior properties compared to their equivalent fibers from RG-PVC. Finally, the performance of upcycled fibers on the removal of dyes from the water was evaluated. The upcycled fibers from waste PVC pipes and pool float outperformed the RG PVC fibers in removing methylene blue from water by showing more than 97% removal efficiency. In addition, the upcycled PVC ES fibers showed more than 80% reusability after five adsorption−desorption cycles. 
    more » « less
  2. ; ; (, Journal of Applied Polymer Science)
    Abstract Polyamide thin‐film composite (PA‐TFC) membranes make large‐scale desalination effective. Interfacial polymerization (IP) is used to make PA‐TFC membranes, but it may limit the range of monomers that can be used, which hinders progress toward advanced membranes. Layer‐by‐layer (LbL) sequential deposition could circumvent kinetic and thermodynamic limitations of the conventional IP process to facilitate incorporation of different co‐monomers into the membrane. The selective layer needs to be deposited onto a microporous support, but depositing LbL coatings on microporous supports often results in defective membranes. Using a poly(vinyl alcohol) (PVA) primer between the support and the LbL polyamide layer may prevent defect formation. The water permeance and salt rejection of a three layer, PVA‐primed, LbL‐based PA‐TFC membrane are discussed and compared to a membrane made without the PVA primer and a commercially available membrane. Mass transfer resistances are analyzed using a series resistance model and appear to be small or even negligible compared to that of the polyamide layer. Incorporation of a sulfonated co‐monomer into the polyamide via LbL is reported. The combination of a PVA primer layer and LbL sequential deposition may expand the range of co‐monomers that could be used relative to polyamide membranes prepared by the conventional IP process. 
    more » « less
  3. ; ; ; ; (, npj Clean Water)
    Abstract In this study, loose nanofiltration membranes made of polysulfone dissolved in co-solvents PolarClean and gamma-Valerolactone were prepared via slot die coating (SDC) on a roll-to-roll (R2R) system by directly coating them onto a support layer or free standing. A solution flow rate of 20 mL/min, substrate speed of 17.1 mm/s, and coating gap of 0.1 mm resulted in the formation of membranes without structural defects. Pre-wetting the support layer with dope solution minimized shrinkage of membrane layer thickness and improved interfacial adhesion. Membrane samples produced using SDC exhibited properties and performance consistent with bench-scale doctor blade extruded samples; pre-wetted and uncompressed samples (SDC-3) exhibited the highest rejection of bovine serum albumin (99.20% ± 1.31%) and along with adequate mean permeability during filtration (70.5 ± 8.33 LMH/bar). This study shows that combining sustainable materials development with SDC provides a holistic approach to membrane separations to bridge materials discovery and membrane formation. 
    more » « less
  4. ; ; ; ; ; ; (, ACS Applied Engineering Materials)
    Zwitterionic polymers have proven to be a promising non-fouling material that can be applied in the design of selective layers of thin film composite (TFC) membranes. Extending the permeability and usage of TFC membranes have attracted increasing interest in membrane-based desalination processes since water-flux reduction associated with biofouling persist nowadays as a common challenge. By virtue of its strong hydration, this polymer category is very useful to counteract biofouling in marine and biomedical systems, but the benefits from their application in membrane technology are still emerging. The efficacy of the non-fouling property as a function of the polymer’s molecular weight remains unknown. In pursuit of that vision, this study fosters new scientific insights via probing different molecular weights of poly(carboxybetain methacrylate) (PCBMA) coated on the surface as a selective layer for the prepared TFC membranes. The coated zwitterionic membranes (zM) exhibited excellent performance to prevent water flux decay in a bench scale forward osmosis system. The prepared zM membranes revealed enhanced hydrophilic properties and retained its operational water-flux when compared to the control. Our results suggest that using an intermediate size molecular weight (PCBMA Mn 50,000) will result in the best operational performance. The intermediate size resulted in the lowest flux decline rate (Rt) of 0.01±0.001 (zM-50) when compared to the unmodified control membrane 0.56 ± 0.071 (M0) after using a model BSA foulant solution. Furthermore, all coated membranes exhibited similar trends in the observed reverse salt flux profiles as well. The constructed zM membranes will serve as a model to develop further selective layers in the construction of TFC membranes. 
    more » « less
  5. ; ; ; ; ; ; ; (, Environmental Science & Technology)
    Affordable thin-film composite (TFC) membranes are a potential alternative to more expensive ion exchange membranes in saltwater electrolyzers used for hydrogen gas production. We used a solution-friction transport model to study how the induced potential gradient controls ion transport across the polyamide (PA) active layer and support layers of TFC membranes during electrolysis. The set of parameters was simplified by assigning the same size-related partition and friction coefficients for all salt ions through the membrane active layer. The model was fit to experimental ion transport data from saltwater electrolysis with 600 mM electrolytes at 10 mA cm–2. When the electrolyte concentration and current density were increased, the transport of major charge carriers was successfully predicted by the model. Ion transport calculated using the model only minimally changed when the negative active layer charge density was varied from 0 to 600 mM, indicating active layer charge was not largely responsible for controlling ion crossover during electrolysis. Based on model simulations, a sharp pH gradient was predicted to occur within the supporting layer of the membrane. These results can help guide membrane design and operation conditions in water electrolyzers using TFC membranes. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email