An official website of the United States government
IntroductionPhotomodifiable azopolymer nanotopographies represent a powerful means of assessing how cells respond to rapid changes in the local microenvironment. However, previous studies have suggested that azopolymers are readily photomodified under typical fluorescence imaging conditions over much of the visible spectrum. Here we assess the stability of azopolymer nanoridges under 1-photon and 2-photon imaging over a broad range of wavelengths. MethodsAzopolymer nanoridges were created via microtransfer molding of master structures that were created using interference lithography. The effects of exposure to a broad range of wavelengths of light polarized parallel to the ridges were assessed on both a spinning-disk confocal microscope and a 2-photon fluorescence microscope. Experiments with liveDictyostelium discoideumcells were also performed using alternating cycles of 514-nm light for photomodification and 561-nm light for fluorescence imaging. Results and DiscussionWe find that for both 1-photon and 2-photon imaging, only a limited range of wavelengths of light leads to photomodification of the azopolymer nanotopography. These results indicate that nondestructive 1-photon and 2-photon fluorescence imaging can be performed over a considerably broader range of wavelengths than would be suggested by previous research.
more »
« less
Large‐Area Photomodification of Nanotopography for Controlling Cell Behavior
Abstract Nanotopographic surfaces are a powerful tool for studying and controlling cell behavior. However, the fabrication of nanotopographic master patterns using conventional photolithography is expensive, which limits the range of designs that can be explored. In this study, a method is demonstrated for the photoreshaping of large‐area patterns of nanoridges. The original master pattern is created using conventional lithography, and an azopolymer replica is prepared using soft lithography. The manipulation of the nanoridges is achieved by projecting light with specific polarizations and exposure times, resulting in controllable widening, buckling, or removal of the ridges. The reprogrammed azopolymer master patterns can then be replicated, creating reproducible new nanotopographies that can be transferred into other materials using a molding procedure. Diffraction can be used for in situ monitoring of the reprogramming during exposure. Image‐analysis methods are used to characterize buckled ridges as a function of exposure time. The response of MCF10A epithelial cells are investigated to buckled nanoridges. A substantial impact of buckling on the dynamics and location of actin polymerization, as well as on the distribution and lengths of contiguous polymerized regions is also observed.
more »
« less
- Award ID(s):
- 2014151
- PAR ID:
- 10539172
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials Interfaces
- Volume:
- 11
- Issue:
- 28
- ISSN:
- 2196-7350
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Interface stress between structural materials and thin film coatings has a significant influence on the resonant frequency of microelectromechanical system (MEMS) resonators. In this work, the axial stress on different types of buckled bridge MEMS resonator structures is controlled through the solid‐to‐solid phase transition of a VO2thin film coating. The devices have identical dimensions, but different buckling orientations and profiles due to the combined effect of overetching and residual thermal stress mismatch. Thermal actuation is used to tune the resonant frequency of the device, but the changes in frequency are found to be dependent on the type of buckling for the device. Thermal actuation is achieved by applying an electrical current to integrated heaters, or by uniform substrate heating. Bidirectional tunability is found when substrate heating is used, while Joule heating shows a monotonic change in frequency. This phenomenon can be attributed to the transition in boundary conditions, where the turning points are indicated by the prominent changes in buckling amplitude. In addition, devices with opposite buckling orientations exhibit different tuning behaviors which can be explained by different bending moments induced by beam stress interface modification.more » « less
-
Thin (slender) steel plates possess shear strength beyond the elastic buckling load which is commonly referred to as the post-buckling capacity. Semi-empirical equations based on experimental tests of plate girders have been used for decades to predict the ultimate post-buckling strength of slender webs. However, several recent studies have shown that the current models for predicting the ultimate shear post-buckling capacity of thin plates are based on some incorrect assumptions regarding their mechanical behavior. As a result, the current design equations provide an approximate estimate of capacity for the range of parameters in the test data upon which they are founded. This paper explores the fundamental behavior of thin plates under pure shear. Such a fundamental examination of shear post-buckling behavior in thin plates is needed to enable design procedures that can optimize a plate’s shear strength and load-deformation performance for a wider range of loading and design parameters. Using finite element analyses, which are validated against available results of previous experimental tests, outputs such as plastic strains, von Mises stresses, principal stresses, and principal stress directions are examined on a buckled plate acting in pure shear. The internal bending, shear, and membrane stresses in the plate’s finite elements are also evaluated. In this study, these evaluations are performed for a simply-supported plate with an aspect ratio equal to 1.0 and slenderness ratio equal to 134. Results show that localized bending in the plates due to the out-of-plane post-buckling deformations appear to be a significant factor in the ultimate shear post-buckling capacity of the plate. Also, the compressive stresses continue to increase beyond the onset of elastic buckling in some regions of the plate, contrary to current design assumptions. Overall, this study provides new insights into the mechanics of shear post-buckling behavior of thin plates that can be exploited for design procedures that are consistent with mechanical behavior.more » « less
-
The ability of biomolecules to exert forces on their surroundings or resist compression from the environment is essential in a variety of biologically relevant contexts. For filaments in the low-temperature limit and under a constant compressive force, Euler buckling theory predicts a sudden transition from a compressed state to a bent state in these slender rods. In this paper, we use a mean-field theory to show that if a semiflexible chain is compressed at a finite temperature with a fixed end-to-end distance (permitting fluctuations in the compressive forces), it exhibits a continuous phase transition to a buckled state at a critical level of compression. We determine a quantitatively accurate prediction of the transverse position distribution function of the midpoint of the chain that indicates this transition. We find that the mean compressive forces are non-monotonic as the extension of the filament varies, consistent with the observation that strongly buckled filaments are less able to bear an external load. We also find that for the fixed extension (isometric) ensemble, the buckling transition does not coincide with the local minimum of the mean force (in contrast to Euler buckling). We also show that the theory is highly sensitive to fluctuations in length in two dimensions and the buckling transition can still be accurately recovered by accounting for those fluctuations. These predictions may be useful in understanding the behavior of filamentous biomolecules compressed by fluctuating forces, relevant in a variety of biological contexts.more » « less
-
Abstract A new type of a positive tone chemically amplified photoresist based on well‐defined, sequence‐controlled polypeptoids with ten repeat‐units are synthesized and their potential for extreme‐UV lithography (EUVL) is demonstrated, resulting in line‐space patterns of 70 nm pitch. The synthesized samples contain 4‐(ethyl) phenol (Eph) and propyne (Ppy) side chains, while their change in solubility upon exposure is induced by the deprotection of 4‐(ethyl) phenol side groups. The resist performance is evaluated using deep UV and extreme‐UV lithography. While all samples are developable in isopropyl alcohol, the content, and the sequence of hydrophobic alkyne side chains lead to a detectable change in solubility, dissolution rate, and resist performance.more » « less
