In this article, a compact multiband antenna design and analysis is presented with a view of ensuring efficient uplink/downlink communications at the same time from a single antenna for CubeSat applications. This design shares the aperture of an S-band slot antenna to accommodate a square patch antenna operating in the X-band. Shared aperture antennas, along with an air gap and dielectric loading, provided good gain in both frequency bands. The S-band patch had an S11 = −10 dB bandwidth of 30 MHz (2013–2043 MHz, 1.5%), and the X-band antenna demonstrated a bandwidth of 210 MHz (8320–8530 MHz, 2.5%). The Axial Ratio (<3 dB) bandwidth of the slot antenna in the S-band is 7 MHz (2013–2020 MHz, 0.35%), and it is 67 MHz (8433–8500 MHz, 0.8%) in the case of patch antenna in the X-band. While the maximum gain in the S-band reached 7.7 dBic, in the X-band, the peak gain was 12.8 dBic. This performance comparison study shows that the antenna is advantageous in terms of high gain, maintains circular polarization over a wideband, and can replace two antennas needed in CubeSats for uplink/downlink, which essentially saves space.
more »
« less
A shared-aperture pentaband antenna with high impedance surface for CubeSat application
A circular polarized (CP) pentaband antenna based on the aperture-in-aperture (AIA) concept is presented for CubeSat applications. This AIA consists of five different bands ranging from L-band to Ka-band. Four different antennas, each operating at a specific frequency band, namely 12 GHz, 18.5 GHz, 26 GHz, and 32 GHz, were incorporated into an L-band (viz. 1.5 GHz) antenna. Notably, the five antennas can operate simultaneously for a CubeSat downlink operation with a frequency ratio of 21.3:1. The antenna structure shows a realized gain of 5–10 dBi with good CP bandwidth (< 3 dB) across the overall operational frequency range. That is, the realized gain of L-band (1.5 GHz), X-band (12.5 GHz), K-band1 (18.5 GHz), K-band2 (26 GHz), and Ka-bands (32 GHz) are 5.05 dBi, 8.21 dBi, 7.33 dBi, 7.97 dBi, and 8.56 dBi. A high impedance surface (HIS) is incorporated with the Ka-band antenna to mitigate the ripples in the radiation pattern created by the interference of surface waves. A prototype was fabricated and tested. The measurement data agrees well with the simulation.
more »
« less
- PAR ID:
- 10539445
- Publisher / Repository:
- Sci Rep
- Date Published:
- Journal Name:
- Scientific Reports
- Volume:
- 14
- Issue:
- 1
- ISSN:
- 2045-2322
- Subject(s) / Keyword(s):
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract In this paper, we propose radial line slot array antenna for 5G fixed beam solutions aimed at integrating multiple frequencies of high gain aperture into a single antenna with a common feed. Thus generated shared aperture will facilitate multi-functional antenna aperture for 5G new radio applications in FR-2 band. With increasing diversity in paradigms of communication systems, especially in mm-wave frequency bands, antenna arrays with specialized, multifunctional radiation capabilities are being pursued. This includes RLSAs for multi-band, multi-polarization and multi-beam radiation. This paper will introduce a low-profile, shared-aperture Radial Line Slot Array (SA-RLSA) antenna for these applications in the mm-wave frequency band. The available design methods for these antennas require complex feeding structures, which could be inconvenient for mass production. This work uses a simple capacitive hole-assisted coaxial feed and a conventional substrate containing the radiating slots on the upper plane. A shared aperture approach is adopted to generate beams at multiple frequencies with pencil and conical shapes and to obtain dual polarization. The measured responses from the fabricated samples for dual-band (28 GHz and 47 GHz), dual-beam (pencil beam at 28 GHz and conical beam at 47 GHz), and dual-pol (28 GHz and 47 GHz with X-pol and 38 GHz with Y-pol) showed a very good agreement with the simulated result. At operating frequencies,$$\sim$$20+ dBi gain is obtained, which can be enhanced by increasing the size of the slotted aperture.more » « less
-
Circularly Polarised Stacked Patch Antennas for X‐Band Uplink/Downlink CubeSat Communication SystemsABSTRACT In this article, multiple circularly polarised (CP) stacked patch antenna designs are proposed with different perturbation techniques that can be used in future CubeSat missions using NASA Near Earth Network (NEN) or Deep Space Network (DSN) ground stations. The stacked patches with different perturbations aim to optimise the axial ratio bandwidth of the antennas to cover both uplink and downlink frequency bands of NASA NEN/DSN. Combining the axial ratio bandwidth of the two stacked patches, proposed antennas can be made wideband or dual‐band to replace multiple antenna systems for uplink and downlink communications. Proposed CP antennas provide the solution to overcome some of the major design challenges, such as antenna placement, limited space for solar cells and mass/volume constraints of CubeSats. The proposed antennas achieve axial ratio (AR) 3 dB bandwidths of 1.2–1.33 GHz (16%–17%) covering the X band uplink and downlink frequencies of NASA NEN. A dual‐band antenna covering the uplink and downlink of NASA DSN is also achieved using the stacked patch antenna design. Alongside a wide axial ratio bandwidth, the antennas also offer a wide axial ratio beamwidth (maximum achieved ) and high RHCP gain (maximum 8.05 dBic gain achieved) RHCP gain. Results of the proposed designs were validated through prototype fabrication and measurements.more » « less
-
This paper presents a wideband low-profile dual-polarized patch antenna with helical-shaped L-probe feeding (HLF) for mmWave 5G mobile device applications. Parametric studies on the HLF structure are performed to identify the optimal specifications. As a result, the optimized antenna achieves a wide bandwidth of 5.4 GHz (24.2–29.6 GHz), good isolation > 18 dB between ports, and 5.1 dBi of good peak realized gain, which is experimentally verified with a 10× upscaled antenna. In addition, various one × four phased arrays with different port configurations and beamform capabilities are designed and simulated for the peak realized gain. The designed antenna array shows a high peak realized gain of 10 dBi, high isolation of 15 dB between the ports, and a small substrate thickness of 0.048λ0 (λ0 is the wavelength of 24.25 GHz). Compared to the state-of-the-art antennas, the designed dual-polarized antenna can operate in the frequency ranges of 24.25–29.6 GHz, including n257, n258, and n261 of the 5G new radio frequency range 2.more » « less
-
null (Ed.)Due to the exponential growth of small satellite technology, novel shapes for antennas have been explored to make them low-cost, lightweight, compact, and easy to deploy. The use of frequency beam-scan antennas reduces the complexity of the small satellite front-end by avoiding the need to use phase shifters, especially when a reliable inter-satellite link (ISL) is required to keep up the communication and the formation accurately in a CubeSat swarm mission. This paper reports the design and a manufacturing process focused on in-space manufacturing (ISM) of a fully 3D-printed leaky-wave antenna, using ULTEM 9085 for aerospace applications. The antenna shows frequency beam steering capabilities from 4.4 GHz to 7.4 GHz, and a gain reconfigurable by angular rotation of the ground planes. The resulting antenna shows a measured peak gain of 10.07 dBi at 6.5 GHz, with a gain reconfigurability, as function of the elevation angle of the ground planes, in the range of 0 to 40°, providing an additional gain from 0 to 2 dBi, respectively.more » « less
An official website of the United States government

