An official website of the United States government
Using direct high-speed imaging, we study the transition between different chip formation modes, and the underlying mechanics, in machining of ductile metals. Three distinct chip formation modes — continuous chip, shear-localized chip, and fragmented chip — are effected in a same material system by varying the cutting speed. It is shown using direct observations that shear-localized chip formation is characterized by shear band nucleation at the tool tip and its propagation towards the free surface, which is then followed by plastic slip along the band without fracture. The transition from shear-localized chip to fragmented chip with increasing cutting speed is triggered by crack initiation at the free surface and propagation towards the tool tip. The extent to which crack travels towards the tool determines whether the chip is partially fragmented or fully fragmented (discontinuous). It is shown that shear localization precedes fracture and controls the crack path in fragmented chip formation. Dynamic strain and strain-rate fields underlying the each chip formation mode are quantified through image correlation analysis of high-speed images. Implications for using machining as an experimental tool for fundamental studies of localization and shear fracture in ductile metals are also discussed.
more »
« less
Direct Measurement of Tool-Chip Contact Stresses in Machining Using Full-Field Photoelasticity
Tool-chip contact stresses are of major interest in developing a basic understanding of the mechanics of machining. The interfacial and sliding conditions along the tool-chip contact in machining differ significantly from that of conventional, lightly loaded, tribological contacts in two major aspects — the occurrence of plastic flow (in the chip) at the sliding interface and intimate nature of the contact where apparent and real contact areas are the same. In this study, we present an experimental method for direct measurement of the tool-chip contact stresses. This involves the use of sapphire as a cutting tool coupled with digital photoelasticity to obtain full-field principal stress difference (isochromatics) and principal stress directions (isoclinics). This enables direct full-field characterization of the tool-chip contact stresses, as well as stresses within the cutting tool, at a micron-scale resolution not achieved previously. Our results show that the shear stress exhibits a maximum at a small distance from the tool tip, while the normal stress decreases monotonically with increasing distance from the tool tip. The maximum shear stress shows a good correlation with the shear flow stress of the material that is being machined. We also briefly discuss applications of the method to derive the stress distribution at the tool flank face and quantify frictional dissipation at both the contacts — tool-chip contact and flank-machined surface contact.
more »
« less
- Award ID(s):
- 2102030
- PAR ID:
- 10541957
- Publisher / Repository:
- American Society of Mechanical Engineers
- Date Published:
- ISBN:
- 978-0-7918-8811-7
- Format(s):
- Medium: X
- Location:
- Knoxville, Tennessee, USA
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The formation of burrs is among the most significant factors affecting quality and productivity in machining. Burrs are a negative byproduct of machining processes that are difficult to avoid because of a limited understanding of the complex burr formation mechanisms in relation to cutting conditions, including both process parameters and tool condition. Thus, the objective of this work was to characterize burr formation under finish machining conditions via a high-speed, high-resolution in-situ experimental method. Various parameters pertaining to burr geometry such as height, thickness, and initial negative shear angle were measured both during and after cutting. Results showed that varying the conditions of uncut chip thickness, tool-wear, and cutting speed all have a significant effect on burr formation, although certain burr metrics were found to be insensitive with respect to different process conditions because the difference was statistically insignificant. This study provides new insights into the relationships between the workpiece material’s microstructure, machining parameters, and tool condition on both crack formation and propagation/plasticity during burr formation. Using digital image correlation (DIC) and a physics-based process model not previously utilized for burr formation analysis, the displacement and corresponding flow stress were calculated at the exit burr root location. This novel semi-analytical approach revealed that the normalized stress at the exit burr root was approximately equal to the flow stress for a variety of different conditions, indicating the potential for model-based prediction of burr formation mechanics. Finally, this study investigates factors that influence fracture evolution during exit burr formation. It was found that negative exit burrs are a direct result of high strain rate and high uncut chip thickness, which was expected, but also a microstructural size effect and a tool-wear effect, neither of which have been previously reported. By harnessing ultra-high-speed imaging and advanced optical microscopy techniques, this manuscript deals with the fundamentals of burr formation, including new insights into material response at the grain-scale to the loads imposed with both sharp and worn tools.more » « less
-
Abstract In recent years, semiconductors, electronics, optics, and various other industries have seen a significant surge in the use of sapphire materials, driven by their exceptional mechanical and chemical properties. The machining of sapphire surfaces plays a crucial role in all these applications. However, due to sapphires’ exceptionally high hardness (Mohs hardness of 9, Vickers hardness of 2300) and brittleness, machining them often presents challenges such as microcracking and chipping of the workpiece, as well as significant tool wear, making sapphires difficult to cut. To enhance the machining efficiency and machined surface integrity, ultrasonic vibration-assisted (UV-A) machining of sapphire has already been studied, showing improved performance with lower cutting force, better surface finish, and extended tool life. Scribing tests using a single-diamond tool not only are an effective method to understand the material removal mechanism and deformation characteristics during such UV-A machining processes but also can be used as a potential process for separating IC chips from wafers. This paper presents a comprehensive study of the UV-A scribing process, aiming to develop an understanding of sapphire’s material removal mechanism under varying ultrasonic power levels and cutting tool geometries. In this experimental investigation, the effect of five different levels of ultrasonic power and three different cutting tool tip angles at various feeding depths on the scribe-induced features of the sapphire surface has been presented with a quantitative and qualitative comparison. The findings indicate that at feeding depths less than 6 μm, UV-A scribing with 40–80% ultrasonic power can reduce cutting force up to 50% and thus improve scribe quality. However, between feeding depths of 6 to 10 μm, this advantage of using ultrasonic vibration gradually diminishes. Additionally, UV-A scribing with a smaller tool tip angle (60°) was found to lower cutting force by 65% and improve scribe quality, effectively inhibiting residual stress formation and microcrack propagation. Furthermore, UV-A scribing also facilitated higher critical feeding depths at around 10 μm, compared to 6 μm in conventional scribing.more » « less
-
Abstract Glacier sliding has major environmental consequences, but friction caused by debris in the basal ice of glaciers is seldom considered in sliding models. To include such friction, divergent hypotheses for clast‐bed contact forces require testing. In experiments we rotate an ice ring (outside diameter = 0.9 m), with and without isolated till clasts, over a smooth rock bed. Ice is kept at its pressure‐melting temperature, and meltwater drains along a film at the bed to atmospheric pressure at its edges. The ice pressure or bed‐normal component of ice velocity is controlled, while bed shear stress is measured. Results with debris‐free ice indicate friction coefficients < 0.01. Shear stresses caused by clasts in ice are independent of ice pressure. This independence indicates that with increases in ice pressure the water pressure in cavities observed beneath clasts increases commensurately to allow drainage of cavities into the melt film, leaving clast‐bed contact forces unaffected. Shear stresses, instead, are proportional to bed‐normal ice velocity. Cavities and the absence of regelation ice indicate that, unlike model formulations, regelation past clasts does not control contact forces. Alternatively, heat from the bed melts ice above clasts, creating pressure gradients in adjacent meltwater films that cause contact forces to depend on bed‐normal ice velocity. This model can account for observations if rock friction predicated on Hertzian clast‐bed contacts is assumed. Including debris‐bed friction in glacier sliding models will require coupling the ice velocity field near the bed to contact forces rather than imposing a pressure‐based friction rule.more » « less
-
Abstract Machining-induced residual stresses (MIRS) are a main driver for distortion of thin-walled monolithic aluminum workpieces. Before one can develop compensation techniques to minimize distortion, the effect of machining on the MIRS has to be fully understood. This means that not only an investigation of the effect of different process parameters on the MIRS is important. In addition, the repeatability of the MIRS resulting from the same machining condition has to be considered. In past research, statistical confidence of MIRS of machined samples was not focused on. In this paper, the repeatability of the MIRS for different machining modes, consisting of a variation in feed per tooth and cutting speed, is investigated. Multiple hole-drilling measurements within one sample and on different samples, machined with the same parameter set, were part of the investigations. Besides, the effect of two different clamping strategies on the MIRS was investigated. The results show that an overall repeatability for MIRS is given for stable machining (between 16 and 34% repeatability standard deviation of maximum normal MIRS), whereas instable machining, detected by vibrations in the force signal, has worse repeatability (54%) independent of the used clamping strategy. Further experiments, where a 1-mm-thick wafer was removed at the milled surface, show the connection between MIRS and their distortion. A numerical stress analysis reveals that the measured stress data is consistent with machining-induced distortion across and within different machining modes. It was found that more and/or deeper MIRS cause more distortion.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1115/MSEC2024-124356
