An official website of the United States government
Using direct high-speed imaging, we study the transition between different chip formation modes, and the underlying mechanics, in machining of ductile metals. Three distinct chip formation modes — continuous chip, shear-localized chip, and fragmented chip — are effected in a same material system by varying the cutting speed. It is shown using direct observations that shear-localized chip formation is characterized by shear band nucleation at the tool tip and its propagation towards the free surface, which is then followed by plastic slip along the band without fracture. The transition from shear-localized chip to fragmented chip with increasing cutting speed is triggered by crack initiation at the free surface and propagation towards the tool tip. The extent to which crack travels towards the tool determines whether the chip is partially fragmented or fully fragmented (discontinuous). It is shown that shear localization precedes fracture and controls the crack path in fragmented chip formation. Dynamic strain and strain-rate fields underlying the each chip formation mode are quantified through image correlation analysis of high-speed images. Implications for using machining as an experimental tool for fundamental studies of localization and shear fracture in ductile metals are also discussed.
more »
« less
Direct Measurement of Tool-Chip Contact Stresses in Machining Using Full-Field Photoelasticity
Tool-chip contact stresses are of major interest in developing a basic understanding of the mechanics of machining. The interfacial and sliding conditions along the tool-chip contact in machining differ significantly from that of conventional, lightly loaded, tribological contacts in two major aspects — the occurrence of plastic flow (in the chip) at the sliding interface and intimate nature of the contact where apparent and real contact areas are the same. In this study, we present an experimental method for direct measurement of the tool-chip contact stresses. This involves the use of sapphire as a cutting tool coupled with digital photoelasticity to obtain full-field principal stress difference (isochromatics) and principal stress directions (isoclinics). This enables direct full-field characterization of the tool-chip contact stresses, as well as stresses within the cutting tool, at a micron-scale resolution not achieved previously. Our results show that the shear stress exhibits a maximum at a small distance from the tool tip, while the normal stress decreases monotonically with increasing distance from the tool tip. The maximum shear stress shows a good correlation with the shear flow stress of the material that is being machined. We also briefly discuss applications of the method to derive the stress distribution at the tool flank face and quantify frictional dissipation at both the contacts — tool-chip contact and flank-machined surface contact.
more »
« less
- Award ID(s):
- 2102030
- PAR ID:
- 10541957
- Publisher / Repository:
- American Society of Mechanical Engineers
- Date Published:
- ISBN:
- 978-0-7918-8811-7
- Format(s):
- Medium: X
- Location:
- Knoxville, Tennessee, USA
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The formation of burrs is among the most significant factors affecting quality and productivity in machining. Burrs are a negative byproduct of machining processes that are difficult to avoid because of a limited understanding of the complex burr formation mechanisms in relation to cutting conditions, including both process parameters and tool condition. Thus, the objective of this work was to characterize burr formation under finish machining conditions via a high-speed, high-resolution in-situ experimental method. Various parameters pertaining to burr geometry such as height, thickness, and initial negative shear angle were measured both during and after cutting. Results showed that varying the conditions of uncut chip thickness, tool-wear, and cutting speed all have a significant effect on burr formation, although certain burr metrics were found to be insensitive with respect to different process conditions because the difference was statistically insignificant. This study provides new insights into the relationships between the workpiece material’s microstructure, machining parameters, and tool condition on both crack formation and propagation/plasticity during burr formation. Using digital image correlation (DIC) and a physics-based process model not previously utilized for burr formation analysis, the displacement and corresponding flow stress were calculated at the exit burr root location. This novel semi-analytical approach revealed that the normalized stress at the exit burr root was approximately equal to the flow stress for a variety of different conditions, indicating the potential for model-based prediction of burr formation mechanics. Finally, this study investigates factors that influence fracture evolution during exit burr formation. It was found that negative exit burrs are a direct result of high strain rate and high uncut chip thickness, which was expected, but also a microstructural size effect and a tool-wear effect, neither of which have been previously reported. By harnessing ultra-high-speed imaging and advanced optical microscopy techniques, this manuscript deals with the fundamentals of burr formation, including new insights into material response at the grain-scale to the loads imposed with both sharp and worn tools.more » « less
-
Abstract Machining-induced residual stresses (MIRS) are a main driver for distortion of thin-walled monolithic aluminum workpieces. Before one can develop compensation techniques to minimize distortion, the effect of machining on the MIRS has to be fully understood. This means that not only an investigation of the effect of different process parameters on the MIRS is important. In addition, the repeatability of the MIRS resulting from the same machining condition has to be considered. In past research, statistical confidence of MIRS of machined samples was not focused on. In this paper, the repeatability of the MIRS for different machining modes, consisting of a variation in feed per tooth and cutting speed, is investigated. Multiple hole-drilling measurements within one sample and on different samples, machined with the same parameter set, were part of the investigations. Besides, the effect of two different clamping strategies on the MIRS was investigated. The results show that an overall repeatability for MIRS is given for stable machining (between 16 and 34% repeatability standard deviation of maximum normal MIRS), whereas instable machining, detected by vibrations in the force signal, has worse repeatability (54%) independent of the used clamping strategy. Further experiments, where a 1-mm-thick wafer was removed at the milled surface, show the connection between MIRS and their distortion. A numerical stress analysis reveals that the measured stress data is consistent with machining-induced distortion across and within different machining modes. It was found that more and/or deeper MIRS cause more distortion.more » « less
-
Residual stresses (RS) arise in a wide range of manufacturing processes, including additive manufacturing, welding, forming, grinding, and machining. Accurate characterization and prediction of RS are crucial for optimizing functional performance and structural integrity, as tensile stresses reduce fatigue strength while compressive stresses enhance it. Traditional finite element methods provide detailed insights into RS distributions but are computationally expensive for real-time use. To overcome this limitation, we propose a Physics-Informed Neural Network (PINN) framework that embeds the Prandtl–Reuss constitutive equations for elastoplasticity directly into the loss function, enabling meshfree forward simulation of RS distribution and inverse identification of parameters under Hertzian contact loading. The inverse formulation simultaneously reconstructs stress fields and identifies key parameters—the effective friction coefficient and normalized load factor—from sparse data, addressing the nonuniqueness and instability of traditional inverse methods. Validation against high-fidelity Runge–Kutta–Gill reference solutions shows that residual stress prediction errors remain below 8% across a wide parameter range, while parameter identification errors converge to below 1%. The PINN predictions were compared with representative experimental trends for Ti–6Al–4V under burnishing and orthogonal cutting, confirming consistency across chip-generating and chipless processes. By enabling real-time parameter updates from minimal data, the proposed framework can accelerate the development of digital twins for manufacturing, supporting predictive modeling and process optimization. This advancement provides physics-based rapid RS analysis for critical applications, including bearing contacts and machining process optimization, significantly improving speed and usability over traditional approaches.more » « less
-
During machining, kinetic energy is imparted to a workpiece to remove material. The integrity of the machined surface, which depends on the energy transfer, affects the quality and performance of the product, therefore needs to be quantified. Prior studies have indicated the potential of using machining power, or the power consumption at the tool-chip interface, as a process signature for predicting machined surface integrity. However, direct measurement of machining power is constrained by the availability of special equipment and the associated cost. To address this gap, this paper presents a machine learning-based method for machining power prediction through multi-sensor fusion and sequence-to-sequence translation from acoustic and vibration signals, which represent portions of the in-situ kinetic energy dissipation, to the machining power signal as a process signature. Specifically, a neural network architecture is developed to separately translate the acoustic and vibration signals to corresponding machining power signals. The two predicted power signals are subsequently fused to arrive at a unified power signal prediction. To check for spurious decision logic, the sensor fusion model is interpreted using integrated gradients to reveal temporal regions of the input data which have the most influence on the machining power prediction accuracy of the fusion model. Systematic cutting experiments performed on a lathe using 1018 steel have shown that the developed sensor fusion method for process signature prediction can successfully map machine acoustics to power consumption with 5.6% error, tool vibration to power consumption with 8.2% error, and acoustics and vibration, jointly, to power with 2.5% error. Model parameter interpretation reveals that the vibration signal is more influential on the machining power prediction result than the acoustic signal, but that overall model accuracy is diminished if only the vibration signal is used.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Conference Paper:
- https://doi.org/10.1115/MSEC2024-124356
