An official website of the United States government
Abstract Recently, vibration energy harvesting has been seen as a viable energy source to provide for our energy dependent society. Researchers have studied systems ranging from civil structures like bridges to biomechanical systems including human motion as potential sources of vibration energy. In this work, a bench-top system of a piecewise-linear (PWL) nonlinear vibration harvester is studied. A similar idealized model of the harvester was previously looked at numerically, and in this work the method is adjusted to handle physical systems to construct a realistic harvester design. With the physically realizable harvester design, the resonant frequency of the system is able to be tuned by changing the gap size between the oscillator and mechanical stopper, ensuring optimal performance over a broad frequency range. Current nonlinear harvester designs show decreased performance at certain excitation conditions, but this design overcomes these issues while also still maintaining the performance of a linear harvester at resonance. In this investigation, the system is tested at various excitation conditions and gap sizes. The computational response of the resonance behavior of the PWL system is validated against the experiments. Additionally, the electromechanical response is also validated with the experiments by comparing the output power generated from the experiments with the computational prediction.
more »
« less
Electrical power management and optimization with nonlinear energy harvesting structures
In recent years, great advances in understanding the opportunities for nonlinear vibration energy harvesting systems have been achieved giving attention to either the structural or electrical subsystems. Yet, a notable disconnect appears in the knowledge on optimal means to integrate nonlinear energy harvesting structures with effective nonlinear rectifying and power management circuits for practical applications. Motivated to fill this knowledge gap, this research employs impedance principles to investigate power optimization strategies for a nonlinear vibration energy harvester interfaced with a bridge rectifier and a buck-boost converter. The frequency and amplitude dependence of the internal impedance of the harvester structure challenges the conventional impedance matching concepts. Instead, a system-level optimization strategy is established and validated through simulations and experiments. Through careful studies, the means to optimize the electrical power with partial information of the electrical load is revealed and verified in comparison to the full analysis. These results suggest that future study and implementation of optimal nonlinear energy harvesting systems may find effective guidance through power flow concepts built on linear theories despite the presence of nonlinearities in structures and circuits.
more »
« less
- Award ID(s):
- 1661572
- PAR ID:
- 10547598
- Publisher / Repository:
- SAGE Publications
- Date Published:
- Journal Name:
- Journal of Intelligent Material Systems and Structures
- Volume:
- 30
- Issue:
- 2
- ISSN:
- 1045-389X
- Format(s):
- Medium: X Size: p. 213-227
- Size(s):
- p. 213-227
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Vibration energy harvesting is increasingly being seen as a viable energy source to provide for our energy-dependent society. There has been great interest in scavenging previously unused or wasted energy in a large variety of systems including vibrating machinery, ocean waves and human motion. In this work, a bench-top system of a piecewise-linear nonlinear vibration energy harvester is studied. A similar idealized model of the system had previously been studied numerically, and in this work the method is adjusted to better account for the physical system. This new design is able to actively tune the system’s resonant frequency to match the current excitation through the adjustment of the gap size between the oscillator and mechanical stopper; thus maximizing the system response over a broad frequency range. This design shows an increased effective frequency bandwidth compared with traditional linear systems and improves upon current nonlinear designs that are less effective than linear harvesters at resonance. In this paper, the physical system is tested at various excitation conditions and gap sizes to showcase the new harvester design’s effectiveness.more » « less
-
Magnets have received broad attention for vibration energy harvesting due to noncontact, nonlinear forces that may be leveraged among harvesting system elements. Yet, opportunities to integrate multi-directional coupling among a nonlinear energy harvesting system subjected to impulsive excitations have not been scrutinized, despite widespread prevalence of such excitations. To characterize these potentials, this research investigates an energy harvesting system with magnetically induced nonlinearities and coupling effects under impulsive excitations. A system model is formulated and validated with experimental efforts to reconstruct static and dynamic properties of the system via simulations. Then, the model is harnessed to scrutinize dynamic response of the system when subjected to impulse conditions. This research reveals the clear impulse strength dependence and influence of asymmetries on total electrical energy capture and energy conversion efficiency that are tailored by magnetic force coupling. Asymmetry is found to promote greater impulse-to-electrical energy conversion when compared to the symmetric counterpart system and a benchmark nonlinear energy harvester. The roles of initial conditions exemplify how stored energy in an asymmetric energy harvesting system may be released during nonlinear impulsive response. These results provide insights about opportunities and challenges to incorporate magnetic coupling effects in nonlinear energy harvesting systems subjected to impulses.more » « less
-
Abstract A tremendous amount of research has been performed on the design and analysis of vibration energy harvester architectures with the goal of optimizing power output. Often, little attention is given to the actual characteristics of common vibrations from which energy is harvested. In order to shed light on the characteristics of common ambient vibration, data representing 333 vibration signals were downloaded from the NiPS Laboratory “Real Vibration” database, processed, and categorized according to the source of the signal (e. g. vehicle, machine, etc.), the number of dominant frequencies, the nature of the dominant frequencies (e. g. stationary, band-limited noise, etc.), and other metrics. By categorizing signals in this way, the set of idealized vibration inputs (i. e. single stationary frequency, Gaussian white noise, etc.) commonly assumed for harvester input can be corroborated and refined. Furthermore, some heretofore overlooked vibration input types are given motivation for investigation. The classification determined that, of the set of signals used in the study, 64 % of the animal source signals are best described with nonstationary dominant frequencies, 58 % of machine source signals are best described with stationary frequencies, and vehicle source signals are poorly described by any one signal type used in the classification. Nonlinear harvesters with a cubic stiffness term have received extensive attention in the scholarly literature; a numerical simulation and optimization procedure were performed using several representative signals as vibration inputs to determine the prevalence with which such a nonlinear harvester architecture might provide improvement to power output. The analysis indicated that a nonlinear harvester architecture may prove beneficial in increasing power output over a linear counterpart if the signal contains a single, dominant frequency that is not stationary in time, as evidenced by a 14 % increase in harvester power output when employing an architecture with a nonlinear cubic stiffness function. Other studies have indicated that nonlinear architectures may be beneficial for signals with nonstationary frequencies or filtered noise. 53 % of the all characterized signals fall into categories that could potentially benefit from a nonlinear oscillator architecture.more » « less
-
Reverse electrowetting‐on‐dielectric (REWOD)‐based energy harvesting has been studied over the last decade as a novel technique of harvesting energy by actuating liquid droplet(s) utilizing applied mechanical modulation. Much prior research in REWOD has relied on planar electrodes, which by its geometry possess a limited surface area. In addition, most of the prior REWOD works have applied a high bias voltage to enhance the output power that compromises the concept of self‐powering wearable motion sensors in human health monitoring applications. In order to enhance the REWOD power density resulting from an increased electrode–electrolyte interfacial area, high surface area electrodes are required. Herein, electrical and multiphysics‐based modeling approaches of REWOD energy harvester using structured rough surface electrodes are presented. By enhancing the overall available surface area, an increase in the overall capacitance is achieved. COMSOL and MATLAB‐based models are also developed, and the empirical results are compared with the models to validate the performance. Root mean square (RMS) power density is calculated using the RMS voltage across an optimal load impedance. For the proposed rough electrode REWOD energy harvester, maximum power density of 3.18 μW cm−2is achieved at 5 Hz frequency, which is ≈4 times higher than that of the planar electrodes.more » « less
