More Like this

1. Transient dynamics of soft particle glasses in startup shear flow. Part II: Memory and aging

   https://doi.org/10.1122/8.0000448  

   Di Dio, Bruno Flavio; Khabaz, Fardin; Bonnecaze, Roger T.; Cloitre, Michel (July 2022, Journal of Rheology)

   We explore the rheology during a startup flow of well-characterized polyelectrolyte microgel suspensions, which form soft glasses above the jamming concentration. We present and discuss results measured using different mechanical histories focusing on the variations of the static yield stress and yield strain. The behavior of the shear stress growth function is affected by long-lived residual stresses and strains that imprint a slowly decaying mechanical memory inside the materials. The startup flow response is not reversible upon flow reversal and the amplitude of the static yield stress increases with the time elapsed after rejuvenation. We propose an experimental protocol that minimizes the directional memory and we analyze the effect of aging. The static yield strain γ p and the reduced static yield stress σ p / σ y , where σ y is the dynamic yield stress measured from steady flow measurements, are in good agreement with our previous simulations [Khabaz et al., “Transient dynamics of soft particle glasses in startup shear flow. Part I: Microstructure and time scales,” J. Rheol. 65, 241 (2021)]. Our results demonstrate the need to consider memory and aging effects in transient measurements on soft particle glasses. 

   more » « less
2. Characterization of velocity fluctuations and the transition from transient to steady state shear banding with and without pre-shear in a wormlike micelle solution under shear startup by Rheo-NMR

   https://doi.org/10.1515/arh-2020-0001  

   Al-kaby, Rehab N; Codd, Sarah L; Seymour, Joseph D; Brown, Jennifer R (January 2020, Applied Rheology)

   Rheo-NMR velocimetry was used to study shear banding of a 6 wt.% cetylpyridinium chloride (CPCl) worm-like micelle solution under shear startup conditions with and without pre-shear. 1D velocity profiles across the fluid gap of a concentric cylinder Couette shear cell were measured every 1 s following shear startup for four different applied shear rates within the stress plateau. Fitting of the velocity profiles allowed calculation of the shear banding characteristics (shear rates in the high and low shear band, the interface position and apparent slip at the inner rotating wall) as the flow transitioned from transient to steady state regimes. Characteristic timescales to reach steady state were obtained and found to be similar for all shear banding characteristics. Timescales decreased with increasing applied shear rate. Large temporal fluctuations with time were also observed and Fourier transform of the time and velocity autocorrelation functions quantified the fluctuation frequencies. Frequencies corresponded to the elastically driven hydrodynamic instabilities,i.e.vortices, that are known to occur in the unstable high shear band and were dependent upon both applied shear rate and the pre-shear protocol. 

   more » « less
3. Transient topology optimization for efficient design of actively cooled microvascular materials

   https://doi.org/10.1007/s00158-024-03774-2  

   Gorman, Jonathan; Pejman, Reza; Kumar, Sandeep R.; Patrick, Jason F.; Najafi, Ahmad R. (March 2024, Structural and Multidisciplinary Optimization)

   Abstract Microvascular materials containing internal microchannels are able to achieve multi-functionality by flowing different fluids through vasculature. Active cooling is one application to protect structural components and devices from thermal overload, which is critical to modern technology including electric vehicle battery packaging and solar panels on space probes. Creating thermally efficient vascular network designs requires state-of-the-art computational tools. Prior optimization schemes have only considered steady-state cooling, rendering a knowledge gap for time-varying heat transfer behavior. In this study, a transient topology optimization framework is presented to maximize the active-cooling performance and mitigate computational cost. Here, we optimize the channel layout so that coolant flowing within the vascular network can remove heat quickly and also provide a lower steady-state temperature. An objective function for this new transient formulation is proposed that minimizes the area beneath the average temperature versus time curve to simultaneously reduce the temperature and cooling time. The thermal response of the system is obtained through a transient Geometric Reduced Order Finite Element Model (GRO-FEM). The model is verified via a conjugate heat transfer simulation in commercial software and validated by an active-cooling experiment conducted on a 3D-printed microvascular metal. A transient sensitivity analysis is derived to provide the optimizer with analytical gradients of the objective function for further computational efficiency. Example problems are solved demonstrating the method’s ability to enhance cooling performance along with a comparison of transient versus steady-state optimization results. In this comparison, both the steady-state and transient frameworks delivered different designs with similar performance characteristics for the problems considered in this study. This latest computational framework provides a new thermal regulation toolbox for microvascular material designers. 

   more » « less
4. A Two-Stage Cascaded Hybrid Switched-Capacitor DC-DC Converter with 96.9% Peak Efficiency Tolerating 0.6V/μs Input Slew Rate During Startup

   https://doi.org/10.1109/ISSCC42613.2021.9365763  

   Xia, Ziyu; Stauth, Jason T. (February 2021, IEEE International Solid- State Circuits Conference (ISSCC))

   null (Ed.)

   Efficient high-conversion-ratio power delivery is needed for many portable computing applications which require sub-volt supply rails but operate from batteries or USB power sources. In such applications, the power management unit should have a small volume, area, and height while providing fast transient response. Past work has shown favorable performance of hybrid switched-capacitor (SC) converters to reduce the size of needed inductor(s), which can soft-charge high-density SC networks while supporting efficient voltage regulation [1-5]. However, the hybrid approach has its own challenges including balancing the voltage of the flying capacitor and achieving safe but fast startup. Rapid supply transients, including startup, can cause voltage stress on power switches if flying capacitors are not quickly regulated. Past approaches such as precharge networks [3] or fast balancing control [5] have startup times that are on the order of milliseconds. This paper presents a two-stage cascaded hybrid SC converter that features a fast transient response with automatic flying capacitor balancing for low-voltage applications (i.e., 5V:0.4 to 1.2V from a USB interface). The converter is nearly standalone and all gate drive supplies are generated internally. Measured results show a peak efficiency of 96.9%, <; 36mV under/overshoot for 1A/μs load transients, and self-startup time on the order of 10μs (over 100× faster than previous works). 

   more » « less
5. Unsteady Incompressible Thermal Laminar Boundary Layers Subject to Streamwise Pressure Gradients

   Ramirez M. and Araya G. (September 2023, Proceedings of the 21st International Conference of Numerical Analysis and Applied Mathematics)

   This paper focuses on the laminar boundary layer startup process (momentum and thermal) in incompressible flows. The unsteady boundary layer equations can be solved via similarity analysis by normalizing the stream-wise (x), wall-normal (y) and time (t) coordinates by a variable η and τ, respectively. The resulting ODEs are solved by a finite difference explicit algorithm. This can be done for two cases: flat plate flow where the change in pressure are zero (Blasius solution) and wedge or Falkner-Skan flow where the changes in pressure can be favorable (FPG) or adverse (APG). In addition, transient passive scalar transport is examined by setting several Prandtl numbers in the governing equation at two different wall thermal conditions: isothermal and isoflux. Numerical solutions for the transient evolution of the momentum and thermal boundary layer profiles are compared with analytical approximations for both small times (unsteady flow) and large (steady-state flow) times. 

   more » « less