An official website of the United States government
These transect organized radargrams were collected as part of the Center for Oldest Ice Exploration (COLDEX) Science and Technology Center (https://www.coldex.org) in the 2023/24 (CXA2) airborne reconnaissance field season. The raw 3 TB data is deposited at the USAP data center at https://doi.org/10.15784/601768. Flight organized data with additional processing by the University of Kansas to remove electromagnetic interference can be found at the Open Polar Radar server (https://www.openpolarradar.org). The science goal was to characterize the ice sheet between Antarctica's Dome A and Amundsen Scott South Pole Station, to locate sites of interest for the drilling of an ice core with ages spanning the mid-Pleistocene. The radar was deployed on Balser C-FMKB, and flown at ranges of up to 800 km from South Pole Station at velocities of 90 m/s and typical altitude above ground of 600 m. Other instruments included a UHF array system provided by the University of Kansas, a gravity meter, a magnetometer, a laser altimeter, and multiple global navigation satellite systems receivers. The radar data is used for finding ice thickness, bed character, englacial structure and surface assessment. Dataset organization Transects are provided a P/S/T nomenclature, organized by the Project they are flying in, the acquisition System (typically named after the aircraft) and the Transect within the Project. Transects were collected in preplanned systems with the following parameters: CLX radials (CLX/MKB##/R###), attempting to emulate flow lines from Dome A and radiating (in the EPSG:3031 polar stereographic projection) from easting 965 km northing 385 km, with a separation of 0.25 degrees. CLX corridor (CLX/MKB##/X###) rotated from the EPSG:3031 polar stereographic projection at -150 degrees and separated by 10 km in the Y direction and 3.75 km in the X direction CLX2 corridor (CLX2/MKB##/X###) rotated from the EPSG:3031 polar stereographic projection at -150 degrees and separated by 2.5 km in its Y direction and 2.5 km in its X direction NPXE radials (NPXE/MKB##/R####) primarily designed to survey the Upper Byrd Glacier Catchment, constitute spokes radiating from South Pole separated by 2 degrees, in the EPSG:3031 polar stereographic projection Untargeted transit lines used the name of the expedition (CXA2) as the project, and used the flight and the increment within the flight to name the Transect (eg (CXA2/MKB2n/F10T02a). Processing These data represent range compressed VHF radargrams as collected and analyzed in the field. The data are from the MARFA radar system, a 60 MHz ice penetrating radar system that has operated in several different guises over the years. MARFA operates with a 1 microsecond chirp with a design bandwidth of 15 MHz, allowing for ~8 meter range resolution. The record rate after onboard stacking is 200 Hz. High and low gain channels are collected from antennas on each side of the aircraft. In ground processing, the data were stacked 10x coherently to reduce range delayed incoherent surface scattering, and then stacked 5 times incoherently to improve image quality. In this preliminary processing, the effective resolution of deep scattering is several hundred meters due to range ambiguities at depth. Data format These data collection represents georeferenced, time registered instrument measurements (L1B data) converted to SI units. The data format are netCDF3 files, following the formats used for NASA/AAD/UTIG's ICECAP/OIB project at NASA's NSIDC DAAC (10.5067/0I7PFBVQOGO5). Metadata fields can be accessed using the open source ncdump tool, or c, python or matlab modules. A Keyhole Metadata Language (KML) file with geolocation for all transects is also provided. See https://www.loc.gov/preservation/digital/formats/fdd/fdd000330.shtml for resources on NetCDF-3, and https://nsidc.org/data/IR2HI1B/versions/1 for a description of the similar OIB dataset. Acknowledgements This work was supported by the Center for Oldest Ice Exploration, an NSF Science and Technology Center (NSF 2019719). We thank the NSF Office of Polar Programs, the NSF Office of Integrative Activities, and Oregon State University for financial and infrastructure support, and the NSF Antarctic Infrastructure and Logistics Program, and the Antarctic Support Contractor for logistical support. Additional support was provided by the G. Unger Vetlesen Foundation.
more »
« less
Geophysical Investigations of Marie Byrd Land Lithospheric Evolution (GIMBLE) Airborne VHF Radar Transects: 2012/2013 and 2014/2015
Geophysical Investigations of Marie Byrd Land Lithospheric Evolution (GIMBLE) The PIs propose to use airborne geophysics to provide detailed geophysical mapping over the Marie Byrd Land dome of West Antarctica. They will use a Basler equipped with advanced ice penetrating radar, a magnetometer, an airborne gravimeter and laser altimeter. They will test models of Marie Byrd Land lithospheric evolution in three ways: 1) constrain bedrock topography and crustal structure of central Marie Byrd Land for the first time; 2) map subglacial geomorphology of Marie Byrd Land to constrain landscape evolution; and 3) map the distribution of subglacial volcanic centers and identify active sources. Marie Byrd Land is one of the few parts of West Antarctica whose bedrock lies above sea level; as such, it has a key role to play in the formation and decay of the West Antarctic Ice Sheet (WAIS), and thus on eustatic sea level change during the Neogene. Several lines of evidence suggest that the topography of Marie Byrd Land has changed over the course of the Cenozoic, with significant implications for the origin and evolution of the ice sheet. Two seasons were flown. ICP5 operated from Byrd Camp using Basler C-GJKB and the HiCARS2 radar in January 2013, and ICP6 operated from WAIS Divide Camp using Basler C-FMKB and the MARFA radar in late 2014, both supported by the US Antarctic Program and Kenn Borek Air. ICP6 experienced issues with data overflow on the MARFA system, with resulted in missing radar records and timing ambiguities. GIMBLE data can be found at https://www.usap-dc.org/view/project/p0000435. Dataset organization Transects are provided a P/S/T nomenclature, organized by the Project they are flying in, the acquisition System (typically named after the aircraft) and the Transect within the Project. Transects were collected in preplanned systems with the following parameters: MBL corridor (MBL/MKB##/X|Y###) rotated from the EPSG:3031 polar stereographic projection at 61.75 degrees and separated by 7.5 km in the Y direction and 5 km in the X direction, with an origin of X -579.6 km and Y -803.3 km Untargeted transit lines used the name of the expedition (ICP5|ICP6) as the project, and used the flight and the increment within the flight to name the Transect (eg (ICP6/MKB2l/F19T01a). Processing These data represent focused VHF radargrams. The data are from the HiCARS2/MARFA radar system, a 60 MHz ice penetrating radar system that has operated in several different guises over the years. HiCARS2/MARFA operates with a 1 microsecond chirp with a design bandwidth of 15 MHz, allowing for ~8 range resolution. The record rate after onboard stacking is 200 Hz. High and low gain channels are collected from antennas on each side of the aircraft, for MARFA the antennas are recorded separately. In ground processing, the data was processed using focusing SAR over a range delay of 100 nsec following Peters et al, 2007 (doi:10.1109/TGRS.2007.897416). Where data loss in ICP6 prevented the generating of focused data, simpler unfocused 'pik1' data was substituted, with 10 coherent stakes and 5 incoherent stacks. Data format These data collection represents georeferenced, time registered instrument measurements (L1B data) converted to SI units. The data format are netCDF3 files, following the formats used for NASA/AAD/UTIG's ICECAP/OIB project at NASA's NSIDC DAAC (10.5067/0I7PFBVQOGO5). Metadata fields can be accessed using the open source ncdump tool, or c, python or matlab modules. A Keyhole Metadata Language (KML) file with geolocation for all transects is also provided. See https://www.loc.gov/preservation/digital/formats/fdd/fdd000330.shtml for resources on NetCDF-3, and https://nsidc.org/data/IR2HI1B/versions/1 for a description of the similar OIB dataset. Acknowledgements This field work was supported by NSF grant 1043761 to Young; ICP5 aircraft lease costs were supported by NASA Operation Ice Bridge grant NNX11AD33G. Data processing costs were supported by a gift from the G. Unger Vetlesen Foundation and the Open Polar Radar project (NSF grant 2127606)
more »
« less
- PAR ID:
- 10555274
- Publisher / Repository:
- Texas Data Repository
- Date Published:
- Format(s):
- Medium: X
- Location:
- Austin, Texas
- Institution:
- University of Texas Institute for Geophysics
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
These transect organized radargrams were collected as part of the Center for Oldest Ice Exploration (COLDEX) Science and Technology Center (https://www.coldex.org) in the 2022/23 (CXA1) airborne reconnaissance field season. The raw 3 TB data is deposited at the USAP data center at https://doi.org/10.15784/601768. Flight organized data with additional processing by the University of Kansas to remove electromagnetic interference can be found at the Open Polar Radar server (https://www.openpolarradar.org). The science goal was to characterize the ice sheet between Antarctica's Dome A and Amundsen Scott South Pole Station, to locate sites of interest for the drilling of an ice core with ages spanning the mid-Pleistocene. The radar was deployed on Balser C-FMKB, and flown at ranges of up to 800 km from South Pole Station at velocities of 90 m/s and typical altitude above ground of 600 m. Other instruments included a UHF array system provided by the University of Kansas, a gravity meter, a magnetometer, a laser altimeter, and multiple global navigation satellite systems receivers. The radar data is used for finding ice thickness, bed character, englacial structure and surface assessment. Dataset organization Transects are provided a P/S/T nomenclature, organized by the Project they are flying in, the acquisition System (typically named after the aircraft) and the Transect within the Project. Transects were collected in preplanned systems with the following parameters: CLX radials (CLX/MKB##/R###), attempting to emulate flow lines from Dome A and radiating (in the EPSG:3031 polar stereographic projection) from easting 965 km northing 385 km, with a separation of 0.25 degrees. CLX corridor (CLX/MKB##/X###) rotated from the EPSG:3031 polar stereographic projection at -150 degrees and separated by 10 km in the Y direction and 3.75 km in the X direction CLX2 corridor (CLX2/MKB##/X###) rotated from the EPSG:3031 polar stereographic projection at -150 degrees and separated by 2.5 km in its Y direction and 2.5 km in its X direction SAD corridor (SAD/MKB##/X###|Y####) designed to characterize the Saddle region near South Pole approximately perpendicular to the flow lines, rooted from the EPSG:3031 polar stereographic projection at -73.8 degrees and separated by 2.5 km in its Y direction and 2.5 km in the its X direction Untargeted transit lines used the name of the expedition (CXA1) as the project, and used the flight and the increment within the flight to name the Transect (eg (CXA1/MKB2n/F10T02a). Processing These data represent range compressed VHF radargrams as collected and analyzed in the field. The data are from the MARFA radar system, a 60 MHz ice penetrating radar system that has operated in several different guises over the years. MARFA operates with a 1 microsecond chirp with a design bandwidth of 15 MHz, allowing for ~8 range resolution. The record rate after onboard stacking is 200 Hz. High and low gain channels are collected from antennas on each side of the aircraft. In ground processing, the data were stacked 10x coherently to reduce range delayed incoherent surface scattering, and then stacked 5 times incoherently to improve image quality. In this preliminary processing, the effective resolution of deep scattering is several hundred meters due to range ambiguities at depth. Data format These data collection represents georeferenced, time registered instrument measurements (L1B data) converted to SI units. The data format are netCDF3 files, following the formats used for NASA/AAD/UTIG's ICECAP/OIB project at NASA's NSIDC DAAC (10.5067/0I7PFBVQOGO5). Metadata fields can be accessed using the open source ncdump tool, or c, python or matlab modules. A Keyhole Metadata Language (KML) file with geolocation for all transects is also provided. See https://www.loc.gov/preservation/digital/formats/fdd/fdd000330.shtml for resources on NetCDF-3, and https://nsidc.org/data/IR2HI1B/versions/1 for a description of the similar OIB dataset. Acknowledgements This work was supported by the Center for Oldest Ice Exploration, an NSF Science and Technology Center (NSF 2019719). We thank the NSF Office of Polar Programs, the NSF Office of Integrative Activities, and Oregon State University for financial and infrastructure support, and the NSF Antarctic Infrastructure and Logistics Program, and the Antarctic Support Contractor for logistical support. Additional support was provided by the G. Unger Vetlesen Foundation.more » « less
-
Marie Byrd Land (MBL), West Antarctica, is poorly studied geologically due to its ice cover and remoteness. As a result, the timing and magnitude of tectonic and erosional events, such as the tectonic uplift of the Marie Byrd Land dome and the incision of the DeVicq Glacial Trough, are debated. When faced with problems difficult to study and solve through in-person field work, it becomes necessary to turn to modeling. Pecube is a thermo-kinematic modeling program that uses topographic and crustal thermal data to calculate thermochronologic ages across a landscape. Thermochronology uses radiometric dating of mineral systems that are sensitive to specific temperatures and can be used to track cooling related to the tectonic and exhumation history of a region. Model predictions can be compared to observed ages to test the viability of tectonic or geomorphic scenarios. Observed ages used here include dates derived from apatite fission track analysis (AFT; closure temperature ~ 110 °C) and apatite (U-Th)/He dating (AHe; closure temperature ~ 60 °C) of detrital material recovered from offshore MBL that presumably originated from the DeVicq Trough region of MBL. Ongoing modeling efforts will determine how closely calculated bedrock ages compare to new detrital AHe ages, ranging from 23.5-82.8 Ma, and AFT ages, ranging from 49.7-83.6 Ma. These ages broadly correspond to late breakup of Gondwana (~100-85Ma), erosion during and after the uplift of the Marie Byrd Land dome (~30Ma), and glacial incision (beginning at 34 or 20Ma). In light of these new data, alterations were made to existing Pecube models for the DeVicq Trough region to rule out and narrow down the timings and rates possible for both glacial incision at the DeVicq Glacial Trough and exhumation of the Marie Byrd Land dome. Preliminary results suggest that varying glacial incision start time between 34 and 20 Ma, dates proposed for the initiation of the West Antarctic Ice Sheet, does not change resulting bedrock ages significantly. However, varying background exhumation rates results in ages that are broadly consistent with observed ages. Ongoing modeling efforts seek to refine this range further to give insight on the exhumation history and tectonic processes of this region. doi: 10.1130/abs/2024AM-402995more » « less
-
Bedrock topography is a key boundary condition for ice sheet modeling, and determining changes in subglacial topography through time can provide insight into the timing of ice sheet development, the magnitude of glacial erosion, and the co-development of glaciers and glacial topography. West Antarctica hosts an unusually high geothermal gradient supported by hot, low-viscosity mantle which likely enhanced the lithospheric response to West Antarctic Ice Sheet (WAIS) cycles of growth and increased the sensitivity of thermochronometers to landscape evolution on million-year timescales. Thus, a valuable record of glacial landscape change might be recovered from apatite fission track [AFT 80-130°C range] and (U-Th)/He [AHe; 50-90°C] dating, provided that landscape evolution can be distinguished from tectonic signals, including the effects of faults. This study utilizes AFT-AHe thermochronology and thermo-kinematic Pecube modeling to investigate interactions between the hot geotherm, glacial erosion, and inferred crustal structures in the Ford Ranges and the DeVicq Glacier trough in western and central Marie Byrd Land (MBL), respectively. The Ford Ranges host glacial troughs (up to 3km relief) dissecting a low-relief erosional surface. Previous work suggests a majority of bedrock exhumation and cooling occurred at/by 80 Ma. However, new data hint at renewed exhumation linked to glacial incision since WAIS formation at 34 or 20 Ma. Prior (U-Th)/He zircon dates from exposures of crystalline bedrock span 90 – 67 Ma. New AHe bedrock dates are 41 to 26 Ma, while two glacial erratics (presumed to be eroded from walls or floor of glacial troughs) yielded AHe dates of 37 Ma and 16 Ma. Initial modeling results suggest a tectonic boundary between the Ford Ranges and Edward VII Peninsula separating regions with distinct exhumation histories. The boundary may cause differential WAIS incision at 34 or 20 Ma, a possibility being investigated with new models. The DeVicq Glacier trough (>3.5km relief) coincides with a prominent crustal lineament but lacks temperature-time information compared to other regions. The crustal structure may have accommodated motion between elevated central MBL and the subdued crust of the Ford Ranges. Here, owing to the lack of onshore non-volcanic bedrock exposure, we have employed AHe and AFT dating of glacial sediment marine core samples offshore of the DeVicq Glacier to investigate the timing and rates of exhumation of the bedrock carved by the DeVicq trough, with initial results revealing detrital AHe ages as young as 24 Ma. Our new Pecube models test a series of thermal, tectonic, and landscape evolution scenarios against a suite of thermochronologic data, allowing us to assess the timing of glacial incision and WAIS initiation in the Ford Ranges, and to seek evidence of an inferred tectonic boundary at DeVicq Trough. Modeling efforts will be aided by new AHe and AFT analyses from ongoing work. These models combine topographic, tectonic, thermal, and key thermochronologic datasets to produce new insight into the unique cryosphere-lithosphere interactions affecting landscape change in West Antarctica.more » « less
-
West Antarctica hosts an unusually high geothermal gradient supported by hot, low-viscosity mantle which likely enhanced the lithospheric response to West Antarctic Ice Sheet [WAIS] cycles of growth and increased the sensitivity of thermochronometers to landscape evolution. Thus a valuable record of glacial landscape change might be recovered from apatite fission track [AFT 80-130°C range] and (U-Th)/He [AHe; 50-90°C]dating, provided that landscape evolution can be distinguished from tectonic signals, including the effects of faults. This study utilizes AFT-AHe thermochronology and thermo-kinematic Pecube modeling to investigate interactions between the hot geotherm, glacial erosion, and inferred crustal structures in the Ford Ranges and the DeVicq Glacier trough in Marie Byrd Land (MBL). The Ford Ranges host glacial troughs (up to 3km relief) dissecting a low-relief erosional surface. Previous work suggests a majority of bedrock exhumation and cooling occurred at/by 80 Ma. However, new data hint at renewed exhumation linked to glacial incision since WAIS formation at 34 or 20 Ma. Prior (U-Th)/He zircon dates from exposures of crystalline bedrock span 90 – 67 Ma. New AHe bedrock dates are 41 to 26 Ma, while two glacial erratics (presumed to be eroded from walls or floor of glacial troughs) yielded AHe dates of 37 Ma and 16 Ma. The DeVicq Glacier trough (>3.5km relief) likely coincides with a regional fault but lacks temperature-time information compared to other regions. The structure may have accommodated motion between elevated central MBL and the subdued crust of the Ford Ranges. We are acquiring AHe and AFT for onshore and offshore samples to compare uplift and exhumation rates for bedrock flanking DeVicq trough. Our new Pecube models test a series of thermal, tectonic, and landscape evolution scenarios against a suite of thermochronologic data, allowing us to assess the timing of glacial incision and WAIS initiation in the FordRanges, and to seek evidence of an inferred tectonic boundary at DeVicq Trough. Modeling efforts will be aided by new AHe analyses from ongoing work. These models combine topographic, tectonic, thermal, and key thermochronologic datasets to produce new insight into the unique cryosphere-lithosphere interactions affecting landscape change in West Antarctica.more » « less
