skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Coexistence of Hardening and Softening Phenomena in Elastomeric Polymers under Nano‐Impact Loading
Abstract This article reports the coexistence of hardening and softening phenomena when polyurea is submitted to repeated nano‐impacts with various impact forces while controlling the strain rate. The manifestation of these phenomena is further elucidated by interrogating ultraviolet irradiated samples under ambient and nitrogen atmospheres, wherein artificial weathering accelerates hardening by reducing the nano‐impact depths as a function of exposure duration while increasing the impact load, nano‐impact repetitions and strain rate sensitivity favored softening. A 21% and 48% increase in indentation depth are recorded after 100 repetitions at a relatively higher force (10 mN) at a low strain rate and low force (2.5 mN) at a relatively higher rate for pristine and weathered polyurea, respectively. Electron microscopy evidences the induced, progressive damage at the nanoscale based on the agglomeration of hard segments, reduced free volume, and weathering‐induced surface embrittlement.  more » « less
Award ID(s):
1925539
PAR ID:
10557297
Author(s) / Creator(s):
;
Publisher / Repository:
Wiley
Date Published:
Journal Name:
Macromolecular Materials and Engineering
Volume:
309
Issue:
10
ISSN:
1438-7492
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Advanced Engineering Materials)
    This research investigates the dynamic response of a novel polyurea foam with different densities by separately submitting samples to single and multiple impacts at different energies ranging from 1.77 to 7.09 J. The impact and transmitted force‐time histories are acquired during the impact events. Deformation of the samples is also recorded using high‐speed photography and analyzed using digital image correlation (DIC) to characterize density‐dependent strain rate and Poisson's ratio. The analyses of the force‐time histories highlight the interrelationship between the incoming impact energy and force characteristics, including amplitude and durations. The experimental results reveal that polyurea foams can absorb nearly 50% of the incoming impact energy irrespective of their density. The dynamic impact efficacy of the foam persists even after sequential impact events are imparted on the same samples, with only a 20% drop in the load‐bearing capacity after seven consecutive impacts. Furthermore, as verified via electron microscopy observations, the higher‐density foam does not exhibit any permanent damage. This high‐density polyurea foam shows reversible auxetic transition at all impact energies considered herein. The outcomes of this research indicate the suitability of polyurea foams for cushioning and impact mitigation applications, especially in repeated biomechanical impact scenarios. 
    more » « less
  2. ; ; (, Macromolecular Materials and Engineering)
    Abstract The core of this research is separated into three domains, the ultrahigh strain rate response of elastomeric polymers, laser‐induced shock waves , and terahertz time‐domain spectroscopy (THz‐TDS). Elastomers, e.g., polyurea, constitute an advance class of materials suitable for many applications, specifically in high impact loading scenarios, thus, a laser‐induced shock wave (LSW) experimental technique is used to investigate the mechanical response of shock‐loaded polyurea. LSW can submit samples to a strain rate exceeding 106s−1at low strains, enabling determination of material intrinsic failure modes. The large deformation induced during shock loading may alter the macromolecule structure, which can only be detected spectroscopically. Therefore, this research incorporated terahertz bulk spectroscopy to detect and report molecular conformational changes. Microscopy techniques were also used to elucidate changes in the microscale properties, morphology, and topography. The interpretation of the results explicated brittle failure in terms of partial and total spallation and, remarkably, ductile failure leading to plastic deformation, including plastic bulging and adiabatic shearing, not previously associated with LSW technique. Furthermore, spectral changes found in the terahertz regime substantiated the validity of terahertz spectroscopy in elucidating the underlying mechanism associated with the impact mitigating properties of dynamically loaded polyurea. 
    more » « less
  3. ; ; ; ; (, Materials characterization)
    null (Ed.)
    Stress-strain responses and twinning characteristics are studied for a rolled AZ31B magnesium alloy under three different stress states: tension along the normal direction (NDT), compression along the rolled direction (RDC), and torsion about the normal direction (NDTOR) using companion specimens interrupted at incremental strain levels. Tension twinning is extensively induced in twinning-favorable NDT and RDC. All the six variants of tension twin are activated under NDT, whereas a maximum of four variants is activated under RDC. Under NDTOR, both tension twins and compression twins are activated at relatively large strains and twinning occurs in a small fraction of favored grains rather than in the majority of grains. Secondary and tertiary twins are observed in the favorably-orientated grains at high strain levels. Deformation under each stress state shows three stages of strain hardening rate: fast decrease (Stage I), sequential increase (Stage II), and progressive decrease (Stage III). The increase in the hardening rate, which is more significant under NDT and RDC as compared to NDTOR, is attributed to the hardening effect of twin boundaries and twinning texture-induced slip activities. The hardening effect of twin boundaries include the dynamic Hall-Petch hardening induced by the multiplication of twin boundaries (TBs) and twin-twin boundaries (TTBs) as well as the hardening effect associated with the energetically unfavorable TTB formation. When the applied plastic strain is larger than 0.05 under NDT and RDC, the tension twin volume fraction is higher than 50%. The twinning-induced texture leads to the activation of non-basal slips mainly in the twinned volume, i.e. prismatic slips under NDT and pyramidal slips under RDC. The low work hardening under NDTOR is due to the prevailing basal slips with reduced twinning activities under NDTOR. 
    more » « less
  4. ; ; ; ; ; (, JOM)
    Abstract The individual effects of strain rate and temperature on the strain hardening rate of a quenched and partitioned steel have been examined. During quasistatic tests, resistive heating was used to simulate the deformation-induced heating that occurs during high-strain-rate deformation, while the deformation-induced martensitic transformation was tracked by a combination of x-ray and electron backscatter diffraction. Unique work hardening rates under various thermal–mechanical conditions are discussed, based on the balance between the concurrent dislocation slip and transformation-induced plasticity deformation mechanisms. The diffraction and strain hardening data suggest that the imposed strain rate and temperature exhibited dissonant influences on the martensitic phase transformation. Increasing the strain rate appeared to enhance the martensitic transformation, while increasing the temperature suppressed the martensitic transformation. 
    more » « less
  5. ; ; ; (, npj Computational Materials)
    Abstract Nanotwinned materials have been widely studied as a promising class of nanostructured materials that exhibit an exceptional combination of high strength, good ductility, large fracture toughness, remarkable fatigue resistance, and creep stability. Recently, an apparent controversy has emerged with respect to how the strength of nanotwinned materials varies as the twin thickness is reduced. While a transition from hardening to softening was observed in nanotwinned Cu when the twin thickness is reduced below a critical value, continuous hardening was reported in nanotwinned ceramics and nanotwinned diamond. Here, by conducting atomistic simulations and developing a theoretical modeling of nanotwinned Pd and Cu systems, we discovered that there exists a softening temperature, below which the material hardens continuously as the twin thickness is reduced (as in nanotwinned ceramics and diamond), while above which the strength first increases and then decreases, exhibiting a maximum strength and a hardening to softening transition at a critical twin thickness (as in nanotwinned Cu). This important phenomenon has been attributed to a transition from source- to stress-controlled plasticity below the softening temperature, and suggests that different hardening behaviors may exist even in the same nanotwinned material depending on the temperature and that at a given temperature, different materials could exhibit different hardening behaviors depending on their softening temperature. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email