This content will become publicly available on September 1, 2025
- Award ID(s):
- 2108623
- PAR ID:
- 10561000
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- HardwareX
- Volume:
- 19
- Issue:
- C
- ISSN:
- 2468-0672
- Page Range / eLocation ID:
- e00548
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
We have developed a low-cost mechanical shutter driver with integrated arbitrary waveform generation for optical switching and control using a programmable system-on-chip device. This microcontroller-based device with configurable digital and analog blocks is readily programmed using free software, allowing for easy customization for a variety of applications. Additional digital and analog outputs with arbitrary timings can be used to control a variety of devices, such as additional shutters, acousto-optical modulators, or camera trigger pulses, for complete control and imaging of laser light. Utilizing logic-level control signals, this device can be readily integrated into existing computer control and data acquisition systems for expanded hardware capabilities.more » « less
-
(Sc 2 O 3 ) x (Ga 2 O 3 ) 1−x was grown by molecular beam epitaxy at low temperatures (100 °C) using a variety of growth sequences to avoid surface segregation of Ga. Continuous and digital growth techniques always produced Ga segregation. This surface segregation was attributed to the stronger bond between the Sc and O compared to the Ga and O. A digital growth technique (alternate opening of Sc and Ga shutters with the O shutter open continuously during the growth) was unsuccessful in eliminating this effect. The segregation was eliminated using a growth technique in which the Ga shutter was closed for a set amount of time toward the end of the growth while the O and Sc shutters remained open. Characterization with reflection high energy electron diffraction, x-ray diffraction, and transmission electron microscopy revealed the growth of a fine-grained polycrystalline film under these conditions. A third growth technique was used that involved closing the Ga shutter for a set amount of time toward the end of the growth while the O and Sc shutters were open continuously. This technique was successful in depositing a uniform film. However, the breakdown field was only 1.40 MV/cm (at 1 mA/cm 2 ). The addition of Ga to Sc 2 O 3 diminished the insulating properties of the film. These initial experiments indicate that phase segregation is likely to be a major issue with most growth techniques and that alloying Ga 2 O 3 with elements other than Sc, such as Gd or Al, might be a more successful approach.more » « less
-
Abstract Marine organisms and ecosystems face multiple, temporally variable stressors in a rapidly changing world. Realistic experiments that incorporate these aspects of physiological stress are important for advancing our ability to understand, predict, and manage their ecological impacts. However, the experimental systems needed to conduct such experiments can be costly. Here, we describe a low‐cost, modular control system that can be used with seawater sensors and actuators to dynamically manipulate multiple seawater variables. It enables researchers to run a variety of realistic multiple‐stressor, variable exposure experiments with a range of marine organisms. This tank controller system is based on the open‐source Arduino prototyping platform and features a custom‐made circuit board with a 16‐bit analog‐to‐digital converter, a real‐time clock, a MicroSD memory card reader, a high‐voltage transistor array, and solderless screw terminal connectors for easy connection of sensors, actuators, and power supplies. The assembly and use of this controller system does not require extensive electronics engineering or programming experience, and each module can be assembled for under 80 USD in parts. To demonstrate the system's capabilities, we present seawater manipulations from experiments involving (1) simultaneous manipulations of dissolved oxygen and pH; (2) fluctuating dissolved oxygen levels; and (3) a controlled stepwise decrease in dissolved oxygen at different temperatures. The low cost and high customizability of this Arduino‐based control system can contribute to expanding capacities for running global change experiments for researchers and students worldwide.
-
When learning to code a student must learn both to create a program and then how to debug said program. Novices often start with print statements to help trace code execution and isolate logical errors. Eventually, they adopt advance debugger practices such as breakpoints, "stepping" through code execution, and "watching" variables as their values are updated. Unfortunately for students working with Arduino devices, there are no debugger tools built into the Arduino IDE. Instead, a student would have to move onto a professional IDE like Atmel Studio and/or acquire a hardware debugger. Except, these options have a steep learning curve and are not intended for a student who has just started to learn how to write code. I am developing an Arduino software library, called Pin Status, to assist novice programmers with debugging common logic errors and provide features specific to the e-textile microcontroller, Adafruit Circuit Playground Classic.more » « less
-
Zmuidzinas, Jonas ; Gao, Jian-Rong (Ed.)An often unglamorous, yet critical, part of most millimeter/submillimeter astronomical instruments is cryogenic temperature monitoring and control. Depending on the operating wavelength of the instrument and detector technology, this could be stable temperatures in the Kelvin range for millimeter heterodyne systems to 100 mK temperatures at sub-micro-Kelvin stability as for many submillimeter bolometer systems. Here we describe a project of the HARDWARE.astronomy initiative to build a low-cost open-source temperature monitoring and control system. The HARDWARE.astronomy Housekeeping Box, or H.aHk Box (pronounced “hack box”) is developed primarily by undergraduates and employs existing open-source devices (e.g Arduino, Raspberry Pi) to reduce costs while also limiting the complexity of the development. The H.aHk Box features a chassis with a control computer and ten expansion slots that can be filled with a variety of expansion cards. These cards include initially an AC 4-wire temperature monitor and PID control cards. Future work will develop 2-wire temperature monitors, stepper motor controller, and high-power supply. The base-system will also be able to interface with other house-keeping systems over USB, serial port and ethernet. The first deployment of the H.aHk Box will be for the ZEUS-2 submillimeter grating spectrometer. All designs, firmware, software and parts list will be published online allowing for other projects to adopt the system and create custom expansion cards as needed. Here we describe the design (including mechanical, electrical, firmware, and software components) and initial performance of the H.aHk Box system with initial AC/DC 4-wire and PID cards.more » « less