An official website of the United States government
We experimentally investigate liquid infiltration into horizontally oriented fiber arrays imposed by sequential drop impacts. Our experimental system is inspired by mammalian fur coats, and our results provide insight to how we expect natural fibers to respond to falling drops and the structure innate to this multiscale covering. Two successive drop impacts are filmed striking three-dimensional-printed fiber arrays with varying densities, surface wettability, and fixed fiber diameter. The penetration depth and the lateral width of drop spreading within fiber layers are functions of drop displacement relative to the liquid already within the array as well as the drop Weber number. Hydrophobic fibers more effectively prevent an increase in penetration depth by the second impacting drop at low impact Weber numbers, whereas hydrophilic fibers ensure lower liquid penetration depth into the array as the Weber number increases. Impact outcomes, such as penetration depth and lateral spreading, are insensitive to impact eccentricity between the first and second drops at high experimental Weber numbers. As expected, denser, staggered fibers reduce infiltration, preventing the entire drop mass from entering the array. Fragmentation of the first drop, which is promoted by hydrophobicity, larger inter-fiber spacing, and higher drop impact velocity, limits increases in lateral spreading and penetration depth of the liquid mass from a subsequent drop.
more »
« less
This content will become publicly available on February 1, 2026
Dynamic drop penetration of vertically oriented fiber arrays
This experimental work investigates the impact dynamics of drops on vertically oriented, three-dimensional-printed (3D-printed) fiber arrays with variations in packing density, fiber arrangement, and wettability. These fiber arrays are inspired by mammalian fur, and while not wholly representative of the entire morphological range of fur, they do reside within its spectrum. We define an aspect ratio, a modified fiber porosity relative to the drop size, that characterizes various impact regimes. Using energy conservation, we derive a model relating drop penetration depth in vertical fibers to the Weber number. In sparse fibers where the Ohnesorge number is less than 4×10−3, penetration depth scales linearly with the impact Weber number. In hydrophobic fibers, density reduces penetration depth when the contact angle is sufficiently high. Hydrophilic arrays have greater penetration than their hydrophobic counterparts due to capillarity, a result that contrasts the drop impact-initiated infiltration of horizontal fibers. Vertical capillary infiltration of the penetrated liquid is observed whenever the Bond number is less than 0.11. For hydrophilic fibers, we predict that higher density will promote drop penetration when the contact angle is sufficiently low. Complete infiltration by the drop is achieved at sufficient times regardless of drop impact velocity.
more »
« less
- Award ID(s):
- 2153740
- PAR ID:
- 10570253
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Physics of Fluids
- Volume:
- 37
- Issue:
- 2
- ISSN:
- 1070-6631
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This experimental work builds on our previous studies on the post-impact characteristics of drops striking three-dimensional-printed fiber arrays by investigating the highly transient characteristics of impact. We measure temporal changes in drop penetration depth, lateral spreading, and drop dome height above the fiber array as the drop impacts. Liquid penetration of vertical fibers may be divided into three sequential periods with linearly approximated rates of penetration: (i) an inertial regime, where penetration dynamics are governed by inertia; (ii) a transitional regime exhibiting inertial and capillary action; and (iii) a capillary regime characterized purely by downward wicking. Horizontal fibers exhibit only the inertial and transitional stages, with wicking only observed horizontally along the direction of fibers. In horizontal hydrophilic fiber arrays, the time duration to reach the maximum lateral deformation of the drop is proportional to We1/4, as observed in drops impacting solid surfaces. There exists a critical Weber number below which the drop shows no radial deformation, and the critical value increases with decreasing fiber density. At large Weber numbers, drops splash. In contrast, vertical fibers restrict the lateral spreading of the drop, thereby suppressing a splash for all tested drop velocities, even those exceeding 5 m/s.more » « less
-
Droplet impacts on solid surfaces produce a wide variety of phenomena such as spreading, splashing, jetting, receding, and rebounding. In microholed surfaces, downward jets through the hole can be caused by the high impact inertia during the spreading phase of the droplet over the substrate as well as the cavity collapse during recoil phase of the droplet. We investigate the dynamics of the jet formed through the single hole during the impacting phase of the droplet on a micro-holed hydrophilic substrate. The sub-millimeter circular holes are created on the 0.2 mm-thickness hydrophilic plastic films using a 0.5 mm punch. Great care has been taken to ensure that the millimeter-sized droplets of water dispensed by a syringe pump through a micropipette tip can impact directly over the micro-holes. A high-speed video photography camera is employed to capture the full event of impacting and jetting. A MATLAB code has been developed to process the captured videos for data analysis. We study the effect of impact velocity on the jet formation including jet velocity, ejected droplet volume, and breakup process. We find that the Weber number significantly affects outcomes of the drop impact and jetting mechanism. We also examine the dynamic contact angle of the contact line during the spreading and the receding phase.more » « less
-
With the developments in nanotechnology, nanofibrous materials attract great attention as possible platforms for fluidic engineering. This requires an understanding of droplet interactions with fibers when gravity plays no significant role. This work aims to classify all possible axisymmetric configurations of droplets on fibers. The contact angle that the drop makes with the fiber surface is allowed to change from 0° to 180°. Nodoidal apple-like droplets with inverted menisci cusped toward the droplet center and unduloidal droplets with menisci cusped away from the droplet center were introduced and fully analyzed. The existing theory describing axisymmetric droplets on fibers is significantly enriched introducing new morphological configurations of droplets. It is experimentally shown that the barreled droplets could be formed on non-wettable fibers offering contact angles greater than 90°. The theory was quantitatively confirmed with hemispherical droplets formed at the end of a capillary tube and satisfying all the boundary conditions of the model. It is expected that the developed theory could be used for the design of nanofiber-based fluidic devices and for drop-on-demand technologies.more » « less
-
Thanks to its comparable specific mechanical properties to glass fibers, silk is a natural fiber that can be used as an eco-friendly alternative to synthetic reinforcing fibers in composite materials. Compared to natural fibers, especially plant fibers, silk enjoys higher mechanical performances, lower density, and higher elongation even at low temperatures, silk also exhibits other attractive qualities like flame resistance and being naturally continuous. However, silk is known to be prone to moisture absorption from surrounding humid environments. Moisture absorption may alter the silk/resin dynamics during composite manufacturing, and later lead to prem-ature degradation in the composite thermomechanical properties. This study investigates the effect of humidity on silk/resin wettability using two different resins (one epoxy and one vinyl ester) and three different silk architectures. Silk fibers are first exposed to different relative humidity environments. Subsequently, the affinity of the conditioned silk to a set of resins is assessed through measurements of silk/resin contact angle over time. Different silk/resin systems were observed to have contrasting responses to humidity exposure. While some silk/resin systems, such as Ahimsa/epoxy, did not show any change after humidity exposure. Other combinations showed tremendous susceptibility of silk/resin affinity to prior exposure of silk to humidity. For instance, although starting at virtually the same initial hydrophobic contact angle of ~123 degrees, Habotai silk/epoxy samples had contrasting wetting times. While the dried Habotai silk reached full wetting after around 5 minutes, the silk samples exposed to humidity took around 1 hour to reach full im-pregnation. These findings demonstrate the importance of humidity exposure control in silk reinforced composites. Keywords: Natural-Fiber Composites, Contact Angle, Silk, Wettability, Humidity.more » « less
