An official website of the United States government
Abstract There is an urgent need for developing collaborative process-defect modeling in metal-based additive manufacturing (AM). This mainly stems from the high volume of training data needed to develop reliable machine learning models for in-situ anomaly detection. The requirements for large data are especially challenging for small-to-medium manufacturers (SMMs), for whom collecting copious amounts of data is usually cost prohibitive. The objective of this research is to develop a secured data sharing mechanism for directed energy deposition (DED) based AM without disclosing product design information, facilitating secured data aggregation for collaborative modeling. However, one major obstacle is the privacy concerns that arise from data sharing, since AM process data contain confidential design information, such as the printing path. The proposed adaptive design de-identification for additive manufacturing (ADDAM) methodology integrates AM process knowledge into an adaptive de-identification procedure to mask the printing trajectory information in metal-based AM thermal history, which otherwise discloses substantial printing path information. This adaptive approach applies a flexible data privacy level to each thermal image based on its similarity with the other images, facilitating better data utility preservation while protecting data privacy. A real-world case study was used to validate the proposed method based on the fabrication of two cylindrical parts using a DED process. These results are expressed as a Pareto optimal solution, demonstrating significant improvements in privacy gain and minimal utility loss. The proposed method can facilitate privacy improvements of up to 30% with as little as 0% losses in dataset utility after de-identification.
more »
« less
This content will become publicly available on October 1, 2025
Photopolymerization of Stainless Steel 420 Metal Suspension: Printing System and Process Development of Additive Manufacturing Technology toward High-Volume Production
As the metal additive manufacturing (AM) field evolves with an increasing demand for highly complex and customizable products, there is a critical need to close the gap in productivity between metal AM and traditional manufacturing (TM) processes such as continuous casting, machining, etc., designed for mass production. This paper presents the development of the scalable and expeditious additive manufacturing (SEAM) process, which hybridizes binder jet printing and stereolithography principles, and capitalizes on their advantages to improve productivity. The proposed SEAM process was applied to stainless steel 420 (SS420) and the processing conditions (green part printing, debinding, and sintering) were optimized. Finally, an SS420 turbine fabricated using these conditions successfully reached a relative density of 99.7%. The SEAM process is not only suitable for a high-volume production environment but is also capable of fabricating components with excellent accuracy and resolution. Once fully developed, the process is well-suited to bridge the productivity gap between metal AM and TM processes, making it an attractive candidate for further development and future commercialization as a feasible solution to high-volume production AM.
more »
« less
- Award ID(s):
- 2236894
- PAR ID:
- 10577212
- Publisher / Repository:
- Journal of Manufacturing and Materials Processing
- Date Published:
- Journal Name:
- Journal of Manufacturing and Materials Processing
- Volume:
- 8
- Issue:
- 5
- ISSN:
- 2504-4494
- Page Range / eLocation ID:
- 191
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Nature provides us with a large number of functional material systems consisting of hierarchical structures, where significant variations in dimensions are present. Such hierarchical structures are difficult to build by traditional manufacturing processes due to manufacturing limitations. Nowadays, three-dimensional (3D) objects with complex structures can be built by gradually accumulating in a layer-based additive manufacturing (AM); however, the hierarchical structure measured from macroscale to nanoscale sizes still raises significant challenges to the AM processes, whose manufacturing capability is intrinsically specified within a certain scope. It is desired to develop a multiscale AM process to narrow this gap between scales of feature in hierarchical structures. This research aims to investigate an integration approach to fabricating hierarchical objects that have macro-, micro-, and nano-scales features in an object. Firstly, the process setup and the integrated process of two-photon polymerization (TPP), immersed surface accumulation (ISA), and mask image projection-based stereolithography (MIP-SL) were introduced to address the multiscale fabrication challenge. Then, special hierarchical design and process planning toward integrating multiple printing processes are demonstrated. Lastly, we present two test cases built by our hierarchical printing method to validate the feasibility and efficiency of the proposed multiscale hierarchical printing approach. The results demonstrated the capability of the developed multiscale 3D printing process and showed its future potential in various novel applications, such as optics, microfluidics, cell culture, as well as interface technology.more » « less
-
Additive manufacturing (AM) of metals often results in parts with unfavorable mechanical properties. Laser peening (LP) is a high strain rate mechanical surface treatment that hammers a workpiece and induces favorable mechanical properties. Peening strain hardens a surface and imparts compressive residual stresses improving the mechanical properties of a material. This work investigates the role of LP on layer-by-layer processing of 3D printed metals using finite element analysis. The objective is to understand temporal and spatial residual stress development after thermal and mechanical cancellation caused by cyclically coupling printing and peening. Results indicate layer peening frequency is a critical process parameter affecting residual stress redistribution and highly interdependent on the heat generated by the printing process. Optimum hybrid process conditions were found to exists that favorably enhance mechanical properties. With this study, hybrid-AM has ushered in the next evolutionary step in AM and has the potential to profoundly change the way high value metal goods are manufactured.more » « less
-
Manoj Gupta (Ed.)Three-dimensional (3D) printing with continuous carbon-fiber-reinforced polymer (C-CFRP) composites is under increasing development, as it offers more versatility than traditional molding processes, such as the out-of-autoclave-vacuum bag only (OOA-VBO) process. However, due to the layer-by-layer deposition of materials, voids can form between the layers and weaken some of the parts’ properties, such as the interlaminar shear strength (ILSS). In this paper, a novel mold-less magnetic compaction force-assisted additive manufacturing (MCFA-AM) method was used to print carbon nanofiber (CNF) z-threaded CFRP (ZT-CFRP) laminates with significantly improved ILSS and reduced void content compared to traditional C-CFRP laminates, which are printed using a no-pressure 3D-printing process (similar to the fused-deposition-modeling process). The radial flow alignment (RFA) and resin-blending techniques were utilized to manufacture a printing-compatible fast-curing ZT-CFRP prepreg tape to act as the feedstock for a MCFA-AM printhead, which was mounted on a robotic arm. In terms of the ILSS, the MCFA-AM method coupled with ZT-CFRP nanomaterial technology significantly outperformed the C-CFRP made with both the traditional no-pressure 3D-printing process and the OOA-VBO molding process. Furthermore, the mold-less MCFA-AM process more than doubled the production speed of the OOA-VBO molding process. This demonstrates that through the integration of new nanomaterials and 3D-printing techniques, a paradigm shift in C-CFRP manufacturing with significantly better performance, versatility, agility, efficiency, and lower cost is achievable.more » « less
-
null (Ed.)Abstract 3D printing has been extensively used for rapid prototyping as well as low-volume production in aerospace, automotive, and medical industries. However, conventional manufacturing processes (i.e., injection molding and CNC machining) are more economical than 3D printing for high-volume mass production. In addition, current 3D printing techniques are not capable of fabricating large components due to the limited build size of commercially available 3D printers. To increase 3D printing throughput and build volume, a novel cooperative 3D printing technique has been recently introduced. Cooperative 3D printing is an additive manufacturing process where individual mobile 3D printers collaborate on printing a part simultaneously, thereby increasing printing speed and build volume. While cooperative 3D printing has the potential to fabricate larger components more efficiently, the mechanical properties of the components fabricated by cooperative 3D printing have not been systematically characterized. This paper aims to develop a data-driven predictive model that predicts the tensile strength of the components fabricated by cooperative 3D printing. Experimental results have shown that the predictive model is capable of predicting tensile strength as well as identifying the significant factors that affect the tensile strength.more » « less
