An official website of the United States government
Accurate characterization of the response of coastal structures when subjected to tsunami-like waves is important for structural engineering assessment and design. The weakly-compressive Smoothed Particle Hydrodynamic (SPH) model can theoretically investigate such phenomena in both horizontal and vertical directions. Yet, the convergence of the solutions is sensitive to physical and numerical parameters used in the modeling. In this paper, multiple three- and two-dimensional SPH models are used to study the numerical convergence of free-surface elevation solutions for various initial inter-particle distances, domain locations along the flume and vicinity of the structure, and unbroken and broken wave flow conditions. The results are used to infer on the trade-offs between the accuracy of the SPH solutions and computational costs of the simulations, including computing time and data storage requirements. Two-dimensional models and an approximate ratio of ten particles per wave height can reasonably predict the nonturbulent unbroken wave case. The broken wave case requires three-dimensional models and four times the ratio of particles per wave height. A correlation between experimental and numerical results is then performed, showing adequacy of the free-surface elevation converged SPH models to capture global force responses. The distribution of horizontal and vertical pressures exerted on the elevated structure are characterized and compared with an analytical equation derived from the experimental dataset, highlighting the symbiotic relationship between experimental data, for calibration of the models, and numerical insights, for physical setup design. For example, additional instruments should be placed at strategic locations in future experimental programs to further validate numerical local responses, such as pressures near the edges and corners of structures. Such insights are important to support future work and development of updated US and European guidelines for the design of overland built infrastructures.
more »
« less
Numerical modeling of hydrodynamics on an elevated residential structure from varied wave and surge conditions using OpenFOAM
A Computational Fluid Dynamic (CFD) model study of wave and structure interactions on an elevated residential building under various air gap and surge/wave conditions was performed using the olaFlow, an open-source program using the OpenFOAM (Open-source Fields Operation And Manipulation) platform. The numerical model results, including free surface elevation, wave velocity, and vertical pressures on the underside of the elevated structure, showed a good agreement with the measured time-series data from the 1:6 scale hydraulic experiment (Duncan et al., 2021). The numerical simulations were used to extend the physical model tests by computing the vertical distribution of the pressure and resulting wave-induced horizontal forces/pressures, which were not measured in the physical model studies. The simulated results indicate that the pattern of pressure distributions at the frontal face of the elevated structure was controlled by water depth and wavebreaking types (nonbreaking, breaking, and broken waves). The wave induced-vertical force on the elevated structure strongly depends on wave height and the air gap, which is a net elevation from the still water level to the bottom of the structure, but the horizontal force shows complicated patterns due to the varied surge levels (flow depth), wave heights and air gaps. The new dimensionless parameter, α′/h, comprised of the air gap, incident wave height, and flow depth, is introduced and utilized to predict the horizontal forces on the elevated structure.
more »
« less
- Award ID(s):
- 2103713
- PAR ID:
- 10579283
- Publisher / Repository:
- Elsevier
- Date Published:
- Journal Name:
- Coastal Engineering
- Volume:
- 178
- Issue:
- C
- ISSN:
- 0378-3839
- Page Range / eLocation ID:
- 104204
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
A 1:16 scaled physical model was constructed to investigate the effectiveness of a seawall, a submerged breakwater, and mangrove forests to mitigate overland flooding and forces on structures in an idealized urban coastal environment. The experiment was performed using tsunami-like waves at different water levels, wave amplitudes, and time scales to simulate long-wave dynamics. The baseline condition (no mitigation), seawall, submerged breakwater, and mangrove forest were tested individually, and the seawall and submerged breakwater were also tested in combination. Wave gauges, acoustic Doppler velocimeters, loadcells, and pressure gauges were used to measure wave elevations, velocities, forces, and pressures on coastal structures, respectively. The performance of these hard structures and mangroves was compared through their effects on wave elevation, particle velocity, and force reduction. Experimental results showed that each protecting structure reduced the horizontal wave forces and inland flow hydrodynamics in the low-water-level case, with a similar performance by the individual seawall, submerged breakwater, and four rows of mangroves. The combined configuration, when the seawall and submerged breakwater were installed simultaneously, caused the most significant maximum force percent reduction by approximately 50%, while mangrove forests arranged in eight rows resulted in a force reduction of 46% in the first building array. However, in the high-water-level cases, the impulsive force measured with the presence of the submerged breakwater was larger than in the baseline case; thus, the submerged breakwater may amplify the impulsive force on the vertical building rows for certain incident wave conditions. Generally, the combined hard structures induced the lowest force reduction factor measured in almost every building row compared to the seawall, submerged breakwater, and mangroves considered separately for all wave conditions and water levels. That means this multi-tiered configuration showed better performance than individual alternatives in reducing horizontal forces inland than the individual alternatives considered separately.more » « less
-
A prototype-scale physical model was used to study wave height attenuation through an idealized mangrove forest and the resulting reduction of wave forces and pressures on a vertical wall. An 18 m transect of a Rhizophora forest was constructed using artificial trees, considering a baseline and two mangrove stem density configurations. Wave heights seaward, throughout, and shoreward of the forest and pressures on a vertical wall landward of the forest were measured. Mangroves reduced wave-induced forces by 4%–43% for random waves and 2%–38% for regular waves. For nonbreaking wave cases, the shape of the pressure distribution was consistent, implying that the presence of the forest did not change wave-structure interaction processes. Analytical methods for determining nonbreaking wave-induced loads provided good estimations of measured values when attenuated wave heights were used in equations. The ratio of negative to positive force ranged between 0.14 and 1.04 for regular waves and 0.31 to 1.19 for random waves, indicating that seaward forces can be significant and may contribute to destabilization of seawalls during large storms. These results improve the understanding of wave-vegetation-structure interaction and inform future engineering guidelines for calculating expected design load reductions on structures sheltered by emergent vegetation.more » « less
-
Coastal regions host significantly higher population densities compared to inland areas, and coastal communities are at risk for damage due to wave forces during hurricane or storm events. To better understand wave-structure interaction for the robust design of coastal structures, a physical model was constructed and tested to measure wave-induced pressures on three vertical walls with varying widths. Forces determined by integrating measured pressures over the face of each wall were compared with existing analytical formulations for determining wave forces on walls. Results indicate that blockage, the term used to account for the ratio of the wall area to the cross-sectional flow area, influences the wave forces experienced by a wall and that this factor is not accounted for in certain contemporary models.more » « less
-
An on-grade and an elevated specimen were tested and exposed to regular waves, in the Directional Wave Basin (DWB) at Oregon State University, with varying water depths and wave heights to simulate typical wave/surge conditions resulting from landfall hurricanes on low-lying barrier islands such as Hurricane Sandy that impacted the US East Coast in 2012 and Hurricane Ike that impacted the US Gulf Coast in 2008. Several instruments were used in the experiment, including nine wire resistance wave gauges located offshore, eight ultrasonic wave gauges located onshore near the specimens, four acoustic-doppler velocimeters, twelve pressure sensors, four load cells, and four triaxial accelerometers located on the specimens. The data (water depth, wave height, velocity, pressure, force, acceleration) gathered can help engineers and numerical modelers better understand the wave-structure interaction and help in improving design criteria of coastal light wood frame residential structures subjected to hurricane overland surge and wave loading.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.coastaleng.2022.104204
