An official website of the United States government
Abstract A non‐volatile conjugated polymer‐based electrochemical memristor (cPECM), derived from sodium 4‐[(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐2‐yl)methoxy]butane‐2‐sulfonate (S‐EDOT), is fabricated through roll‐to‐roll printing and exhibited neuromorphic properties. The 3‐terminal device employed a “read” channel where conductivity of the water‐soluble, self‐doped S‐PEDOT is equated to synaptic weight and was electrically decoupled from the programming electrode. For the model system, a +2500 mV programming pulse of 100 ms duration resulted in a 0.136 μS resolution in conductivity change, giving over 1000 distinct conductivity states for one cycle. The minimum programming power requirements of the cPECM was 0.31 pJ mm−2and with advanced printing techniques, a 0.1 fJ requirement for a 20 μm device is achievable. The mathematical operations of addition, subtraction, multiplication, and division are demonstrated with a single cPECM, as well as the logic gates AND, OR, NAND, and NOR. This demonstration of a printed cPECM is the first step toward the implementation of a mass produced electrochemical memristor that combines information storage and processing and may allow for the realization of printable artificial neural networks.
more »
« less
Roll-to-roll fabrication of three-dimensional self-folding microstructures
Roll-to-roll fabrication setup for self-folding films has been developed to enable high-throughput production of three-dimensional self-folding microstructures, a significant step towards successful commercialization.
more »
« less
- Award ID(s):
- 1848251
- PAR ID:
- 10587538
- Publisher / Repository:
- The Royal Society of Chemistry
- Date Published:
- Journal Name:
- Lab on a Chip
- ISSN:
- 1473-0197
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Roll-to-roll printing has significantly shortened the time from design to production of sensors and IoT devices, while being cost-effective for mass production. But due to less manufacturing tolerance controls available, properties such as sensor thickness, composition, roughness, etc., cannot be precisely controlled. Since these properties likely affect the sensor behavior, roll-to-roll printed sensors require validation testing before they can be deployed in the field. In this work, we improve the testing of Nitrate sensors that need to be calibrated in a solution of known Nitrate concentration for around 1–2 days. To accelerate this process, we observe the initial behavior of the sensors for a few hours, and use a physics-informed machine learning method to predict their measurements 24 hours in the future, thus saving valuable time and testing resources. Due to the variability in roll-to-roll printing, this prediction task requires models that are robust to changes in properties of the new test sensors. We show that existing methods fail at this task and describe a physics-informed machine learning method that improves the prediction robustness to different testing conditions (≈ 1.7× lower in real-world data and ≈ 5× lower in synthetic data when compared with the current state-of-the-art physics-informed machine learning method).more » « less
-
Paper-based analytical devices (PADs) offer a low-cost, user-friendly platform for rapid point-of-use testing. Without scalable fabrication methods, however, few PADs make it out of the academic laboratory and into the hands of end users. Previously, wax printing was considered an ideal PAD fabrication method, but given that wax printers are no longer commercially available, alternatives are needed. Here, we present one such alternative: the air-gap PAD. Air-gap PADs consist of hydrophilic paper test zones, separated by “air gaps” and affixed to a hydrophobic backing with double-sided adhesive. The primary appeal of this design is its compatibility with roll-to-roll equipment for large-scale manufacturing. In this study, we examine design considerations for air-gap PADs, compare the performance of wax-printed and air-gap PADs, and report on a pilot-scale roll-to-roll production run of air-gap PADs in partnership with a commercial test-strip manufacturer. Air-gap devices performed comparably to their wax-printed counterparts in Washburn flow experiments, a paper-based titration, and a 12-lane pharmaceutical screening device. Using roll-to-roll manufacturing, we produced 2700 feet of air-gap PADs for as little as $0.03 per PAD.more » « less
-
Abstract Roll-to-roll (R2R) manufacturing is a highly efficient industrial method for continuously processing flexible webs through a series of rollers. With advancements in technology, R2R manufacturing has emerged as one of the most economical production methods for advanced products, such as flexible electronics, renewable energy devices, and 2D materials. However, the development of cost-effective and efficient manufacturing processes for these products presents new challenges, including higher precision requirements, the need for improved in-line quality control, and the integration of material processing dynamics into the traditional web handling system. This paper reviews the state of the art in advanced R2R manufacturing, focusing on modeling and control, and highlights research areas that need further development.more » « less
-
Abstract For efficient roll-to-roll (R2R) production of flexible electronic components, a precise R2R transfer peeling process is essential, requiring accurate modeling and control. This paper introduces a novel approach to confining the dynamics of a nonlinear R2R mechanical peeling system within a convex set known as a norm-bounded linear differential inclusion (NLDI). This method utilizes constraints on uncertain system variables to create a tighter NLDI representation compared to other convexification techniques. Moreover, it offers drastically reduced computational cost compared to previous methods applied to convexify the R2R peeling system. The NLDI is employed to generate an H∞-optimal controller for the R2R peeling system, and both simulations and experiments demonstrate better dynamic performance compared to other controllers for R2R transfer.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/D5LC00120J
