An official website of the United States government
The effects of C60 incorporated in polymannose‐based resistive switching memory have been systematically investigated for the first time in bioorganic‐based resistive switching memory. C60 with different concentrations (0–7 wt%) is dispersed in polymannose precursor, drop‐casted on ITO/PET substrate, and dried to form a thin film. Electrochemically inert Au–Pd is used as top electrode. The devices with embedded C60 show better endurance and stability. Read memory window decreases and ON/OFF ratio increases as the concentration of C60 increases. Stable retention time up to 10 years is achieved for all of the devices except the one with 7 wt% C60. Based on zeta potential measurement, polymannose is more negatively charged than C60. Hence, C60 functions as an effective interlock that bridges between long molecular chains of polymannose and enhances the resistive switching properties of the polymannose thin film.
more »
« less
This content will become publicly available on November 22, 2025
Natural Organic Pectin Polysaccharide Based Resistive Random Access Memory
Nowadays, non-volatile memory technologies have been widely applied in different areas. Of these memory technologies, non-volatile resistive random access memory (ReRAM) is attractive because of its simple device architecture and fabrication process, high scalability and data density, good performances in terms of switching speed, high power efficiency and reasonably wide memory window. In order to address the issues of disposable and degradation of electronic waste by typical ReRAM with the active layer made of inorganic oxide materials and fossil-fuel based polymeric materials, a green and sustainable strategy has been adopted in producing ReRAM by using natural organic-based materials based on protein and carbohydrate, such as honey, fructose, aloe vera, etc. Among these materials, pectin-polysaccharide thin film has demonstrated promising resistive switching characteristics. The two ranges of pectin concentrations that have been investigated are ³5 mg/ml and £1.5 mg/ml, and it showed that pectin with concentration <1.5 mg/ml reveals a higher ON/OFF ratio. However, the resistive switching characteristics with pectin concentration between 1.5 mg/ml and 5 mg/ml have yet been explored and reported. In this work, pectin with concentrations of 1.5~5 mg/ml were prepared from pectin-polysaccharide solution into the active switching layer, and ReRAM devices with such pectin resistive switching layer were fabricated. The pectin-polysaccharide solution, pectin resistive film, and ReRAM devices were systematically investigated. Surface tension and contact angle of pectin-polysaccharide precursor solutions as a function of pectin concentration on the substrate were measured by a goniometer. Surface topography of solidified thin films was characterized by an atomic force microscope (AFM) and a field-emission scanning electron microscope (FE-SEM). Chemical functional groups of the pectin-polysaccharide precursor solutions and solidified thin films were examined by a Fourier transform infrared (FTIR) spectroscopy. The resistive switching behaviors were characterized and compared by electrical measurement. The results show that 4 mg/ml recorded the highest ON/OFF ratio compared to ever reported values, as well as desirable memory window, non-volatility in retention, and stability over 100 cycles. This study proves that pectin-polysaccharide is a promising green and sustainable bio-organic material for non-volatile ReRAM for electronic applications such as in emerging neuromorphic computing systems.
more »
« less
- PAR ID:
- 10618439
- Publisher / Repository:
- IOP Science
- Date Published:
- Journal Name:
- ECS Meeting Abstracts
- Volume:
- MA2024-02
- Issue:
- 20
- ISSN:
- 2151-2043
- Page Range / eLocation ID:
- 1779 to 1779
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract 2D materials have been of considerable interest as new materials for device applications. Non‐volatile resistive switching applications of MoS2and WS2have been previously demonstrated; however, these applications are dramatically limited by high temperatures and extended times needed for the large‐area synthesis of 2D materials on crystalline substrates. The experimental results demonstrate a one‐step sulfurization method to synthesize MoS2and WS2at 550 °C in 15 min on sapphire wafers. Furthermore, a large area transfer of the synthesized thin films to SiO2/Si substrates is achieved. Following this, MoS2and WS2memristors are fabricated that exhibit stable non‐volatile switching and a satisfactory large on/off current ratio (103–105) with good uniformity. Tuning the sulfurization parameters (temperature and metal precursor thickness) is found to be a straightforward and effective strategy to improve the performance of the memristors. The demonstration of large‐scale MoS2and WS2memristors with a one‐step low‐temperature sulfurization method with simple strategy to tuning can lead to potential applications such as flexible memory and neuromorphic computing.more » « less
-
Abstract Emerging non-volatile memristor-based devices with resistive switching (RS) materials are being widely researched as promising contenders for the next generation of data storage and neuromorphic technologies. Titanium nitride (TiNx) is a common industry-friendly electrode system for RS; however, the precise TiNxproperties required for optimum RS performance is still lacking. Herein, using ion-assisted DC magnetron sputtering, we demonstrate the key importance not only of engineering the TiNxbottom electrodes to be dense, smooth, and conductive, but also understoichiometric in N. With these properties, RS in HfO2-based memristive devices is shown to be optimised for TiN0.96. These devices have switching voltages ≤ ±1 V with promising device-to-device uniformity, endurance, memory window of ~40, and multiple non-volatile intermediate conductance levels. This study highlights the importance of precise tuning of TiNxbottom electrodes to achieve robust performance of oxide resistive switching materials.more » « less
-
Abstract Monolayer molybdenum disulfide has been previously discovered to exhibit non-volatile resistive switching behavior in a vertical metal-insulator-metal structure, featuring ultra-thin sub-nanometer active layer thickness. However, the reliability of these nascent 2D-based memory devices was not previously investigated for practical applications. Here, we employ an electron irradiation treatment on monolayer MoS2film to modify the defect properties. Raman, photoluminescence, and X-ray photoelectron spectroscopy measurements have been performed to confirm the increasing amount of sulfur vacancies introduced by the e-beam irradiation process. The statistical electrical studies reveal the reliability can be improved by up to 1.5× for yield and 11× for average DC cycling endurance in the devices with a moderate radiation dose compared to unirradiated devices. Based on our previously proposed virtual conductive-point model with the metal ion substitution into sulfur vacancy, Monte Carlo simulations have been performed to illustrate the irradiation effect on device reliability, elucidating a clustering failure mechanism. This work provides an approach by electron irradiation to enhance the reliability of 2D memory devices and inspires further research in defect engineering to precisely control the switching properties for a wide range of applications from memory computing to radio-frequency switches.more » « less
-
Abstract The recent upsurge in environmental awareness provokes the widespread usage of green materials in sustainable electronic applications. Herein, the effects of spent coffee grounds (SCGs) on natural rubber (NR)‐based resistive switching (RS) memory are systematically investigated. This study presents the fabrication of a metal‐insulator‐metal (MIM) structure using NR incorporated with SCGs (0 to 8 wt.%) as a memristive layer and sandwiched between electrodes. A significant improvement in the ON/OFF ratio from 104for pure NR to 107, read memory window increased from 2.03 to 2.45 V with improved stability even after 130 cycles of switching is achieved with the optimal concentration of SCGs (6 wt.%). The improved performance after the incorporation of SCGs is attributed to the introduction of key chemical functional groups (C═O, C═C) in the memristive film. By varying the viscosity of NR, bending of test structure, and voltage sweep rate, the effects of trap density and location on the RS performance are established. The RS mechanisms in high and low resistance states are dominated by space‐charge‐limited conduction and Ohm's law, respectively. This research manifests the potential of SCGs in improving the RS performance of bioorganic‐based memory devices.more » « less
