skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


  • NSF Public Access
  • Search Results
  • Subtle differences in recycled polypropylene from rheology to additives impacts ease of circularity in materials extrusion additive manufacture
Title: Subtle differences in recycled polypropylene from rheology to additives impacts ease of circularity in materials extrusion additive manufacture
The decentralized production associated with material extrusion additive manufacture (MEX) has been proposed as an ideal path to increase the circularity of plastics through direct recycling. Although multiple studies have reported on the 3D printing of various recycled plastics, variability in recycled materials, in particular post-consumer waste, challenges the direct extension of these results into production through MEX. Here, we demonstrate filament fabrication and printing of post-consumer polypropylene (PP), where the PP is sourced from clear, cold drink cups from three large international food service and beverage retail chains to provide well defined plastic waste that is perfectly sorted for recycling. These sources for the recycled PP were selected due to their ready availability to enable the results to be directly applied for hobbyist printing, blow molded products to provide good mechanical performance, and the clarity of the PP that suggests formulation design to minimize the PP crystal size. Despite the similarities in the end use product and their physical appearance, the source for the PP impacted the mechanical properties and the visual appearance of the printed objects. These differences can be directly traced to the rheological properties and oxidative stability of the PP at conditions relevant with the print process. These results clearly illustrate differences in initial formulation design and branding details, even when the product is for the same application, impacts the performance of recycled plastics in AM. The high viscosity associated with the PP from blow molding leads to requirements for higher extrusion temperatures for printing. The combination of high temperature and shear during extrusion process of 3D printing degrades the recycled PP. For circularity with MEX with recycled PP, one needs to consider the evolution in the properties of the polymer. Rheological details of recycled plastics are critical to selection of processing conditions and performance of MEX parts. Reporting of rheological data of recycled plastics and these properties after printing is critical to enable translation towards circular 3D printing of recycled plastics.  more » « less
Award ID(s):
2011289
PAR ID:
10641475
Author(s) / Creator(s):
; ; ; ;
Publisher / Repository:
Elseiver
Date Published:
Journal Name:
Additive manufacturing
Volume:
86
ISSN:
2214-8604
Page Range / eLocation ID:
104209
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; (, Journal of Polymer Science)
    Abstract The global production and consumption of plastics has increased at an alarming rate over the last few decades. The accumulation of pervasive and persistent waste plastic has concomitantly increased in landfills and the environment. The societal, ecological, and economic problems of plastic waste/pollution demand immediate and decisive action. In 2015, only 9% of plastic waste was successfully recycled in the United States. The major current recycling processes focus on the mechanical recycling of plastic waste; however, even this process is limited by the sorting/pretreatment of plastic waste and degradation of plastics during the process. An alternative to mechanical processes is chemical recycling of plastic waste. Efficient chemical recycling would allow for the production of feedstocks for various uses including fuels and chemical feedstocks to replace petrochemicals. This review focuses on the most recent advances for the chemical recycling of three major polymers found in plastic waste: PET, PE, and PP. Commercial processes for recycling hydrolysable polymers like polyesters or polyamides, polyolefins, or mixed waste streams are also discussed. 
    more » « less
  2. ; ; ; ; ; (, ACS Applied Polymer Materials)
    Additive manufacturing, otherwise known as three-dimensional (3D) printing, is a rapidly growing technique that is increasingly used for the production of polymer products, resulting in an associated increase in plastic waste generation. Waste from a particular class of 3D-printing, known as vat photopolymerization, is of particular concern, as these materials are typically thermosets that cannot be recycled or reused. Here, we report a mechanical recycling process that uses cryomilling to generate a thermoset powder from photocured parts that can be recycled back into the neat liquid monomer resin. Mechanical recycling with three different materials is demonstrated: two commercial resins with characteristic brittle and elastic mechanical properties and a third model material formulated in-house. Studies using photocured films showed that up to 30 wt% of the model material could be recycled producing a toughness of 2.01 ± 0.55 MJ/m3, within error of neat analogues (1.65 ± 0.27 MJ/m3). Using dynamic mechanical analysis and atomic force microscopy-based infrared spectroscopy, it was determined that monomers diffuse into the recycled powder particles, creating interpenetrating networks upon ultraviolet (UV) exposure. This process mechanically adheres the particles to the matrix, preventing them from acting as failure sites under a tensile load. Finally, 3D-printing of the commercial brittle material with 10 wt% recycle content produced high quality parts that were visually similar. The maximum stress (46.7 ± 6.2 MPa) and strain at break (11.6 ± 2.3%) of 3D-printed parts with recycle content were within error the same as neat analogues (52.0 ± 1.7 MPa; 13.4 ± 1.8%). Overall, this work demonstrates mechanical recycling of photopolymerized thermosets and shows promise for the reuse of photopolymerized 3D-printing waste. 
    more » « less
  3. ; ; ; (, Science)
    null (Ed.)
    Plastics have revolutionized modern life, but have created a global waste crisis driven by our reliance and demand for low-cost, disposable materials. New approaches are vital to address challenges related to plastics waste heterogeneity, along with the property reductions induced by mechanical recycling. Chemical recycling and upcycling of polymers may enable circularity through separation strategies, chemistries that promote closed-loop recycling inherent to macromolecular design, and transformative processes that shift the life-cycle landscape. Polymer upcycling schemes may enable lower-energy pathways and minimal environmental impacts compared with traditional mechanical and chemical recycling. The emergence of industrial adoption of recycling and upcycling approaches is encouraging, solidifying the critical role for these strategies in addressing the fate of plastics and driving advances in next-generation materials design. 
    more » « less
  4. ; ; ; ; (, Advanced Materials)
    Abstract Creating a sustainable economy for plastics demands the exploration of new strategies for efficient management of mixed plastic waste. The inherent incompatibility of different plastics poses a major challenge in plastic mechanical recycling, resulting in phase‐separated materials with inferior mechanical properties. Here, this study presents a robust and efficient dynamic crosslinking chemistry that effectively compatibilizes mixed plastics. Composed of aromatic sulfonyl azides, the dynamic crosslinker shows high thermal stability and generates singlet nitrene species in situ during solvent‐free melt‐extrusion, effectively promoting C─H insertion across diverse plastics. This new method demonstrates successful compatibilization of binary polymer blends and model mixed plastics, enhancing mechanical performance and improving phase morphology. It holds promise for managing mixed plastic waste, supporting a more sustainable lifecycle for plastics. 
    more » « less
  5. ; ; ; ; ; ; ; (, Sustainability)
    The negative environmental impacts of the current linear system of textile and apparel production are well-documented and require urgent action. The sector lacks an effective recycling system, resulting in massive waste and environmental pollution. This paper presents the results of qualitative research involving textile and apparel industry stakeholders, including representatives from brands and retailers, waste collectors, recyclers, non-profit organizations, academic institutions, and government agencies. Our research focused on stakeholder perceptions of the significance and importance of textile circularity, the challenges that exist for transitioning the textile and apparel industry from a linear system to a circular economy (CE), and resources that exist to support this transition. The results of this study call attention to the following urgent requirements: a consistent definition of CE to promote transparency and accountability and prevent greenwashing; improved systems for materials identification, sorting, and pre-processing of post-consumer textile waste to enable recycling; innovations in mechanical recycling technologies to maintain the value of recycled materials; and new, materials-driven approaches to design and manufacturing that are responsive to feedstock variability and diverse consumer needs. The research findings also suggest the need for flexible, regional CEs that are rooted in community partnerships. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email