skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Mechanical Recycling of 3D-Printed Thermosets for Reuse in Vat Photopolymerization
Additive manufacturing, otherwise known as three-dimensional (3D) printing, is a rapidly growing technique that is increasingly used for the production of polymer products, resulting in an associated increase in plastic waste generation. Waste from a particular class of 3D-printing, known as vat photopolymerization, is of particular concern, as these materials are typically thermosets that cannot be recycled or reused. Here, we report a mechanical recycling process that uses cryomilling to generate a thermoset powder from photocured parts that can be recycled back into the neat liquid monomer resin. Mechanical recycling with three different materials is demonstrated: two commercial resins with characteristic brittle and elastic mechanical properties and a third model material formulated in-house. Studies using photocured films showed that up to 30 wt% of the model material could be recycled producing a toughness of 2.01 ± 0.55 MJ/m3, within error of neat analogues (1.65 ± 0.27 MJ/m3). Using dynamic mechanical analysis and atomic force microscopy-based infrared spectroscopy, it was determined that monomers diffuse into the recycled powder particles, creating interpenetrating networks upon ultraviolet (UV) exposure. This process mechanically adheres the particles to the matrix, preventing them from acting as failure sites under a tensile load. Finally, 3D-printing of the commercial brittle material with 10 wt% recycle content produced high quality parts that were visually similar. The maximum stress (46.7 ± 6.2 MPa) and strain at break (11.6 ± 2.3%) of 3D-printed parts with recycle content were within error the same as neat analogues (52.0 ± 1.7 MPa; 13.4 ± 1.8%). Overall, this work demonstrates mechanical recycling of photopolymerized thermosets and shows promise for the reuse of photopolymerized 3D-printing waste.  more » « less
Award ID(s):
1901635 2011401
PAR ID:
10502093
Author(s) / Creator(s):
; ; ; ; ;
Publisher / Repository:
ACS Publications
Date Published:
Journal Name:
ACS Applied Polymer Materials
ISSN:
2637-6105
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Green Chemistry)
    null (Ed.)
    3D printing is an essential tool for rapid prototyping in a variety of sectors such as automotive and public health. The 3D printing market is booming, and it is projected that it will continue to thrive in the coming years. Unfortunately, this rapid growth has led to an alarming increase in the amount of 3D printed plastic waste. 3D printing processes such as stereolithography (SLA) and digital light projection (DLP) in particular generally produce petroleum-based thermosets that are further worsening the plastic pollution problem. To mitigate this 3D printed plastic waste, sustainable alternatives to current 3D printing materials must be developed. The present review provides a comprehensive overview of the sustainable advances in SLA/DLP 3D printing to date and offers a perspective on future directions to improve sustainability in this field. The entire life cycle of 3D printed parts has been assessed by considering the feedstock selection and the end-of-use of the material. The feedstock selection section details how renewable feedstocks (from lignocellulosic biomass, oils, and animal products) or waste feedstocks ( e.g. , waste cooking oil) have been used to develop SLA/DLP resins. The end-of-use section describes how materials can be reprocessed ( e.g. thermoplastic materials or covalent adaptable networks) or degraded (through enzymatic or acid/base hydrolysis of sensitive linkages) after end-of-use. In addition, studies that have employed green chemistry principles in their resin synthesis and/or have shown their sustainable 3D printed parts to have mechanical properties comparable to commercial materials have been highlighted. This review also investigates how aspects of sustainability such as recycling for feedstock/end-of-use or biodegradation of 3D printed parts in natural environments can be incorporated as future research directions in SLA/DLP. 
    more » « less
  2. ; ; ; ; (, Additive manufacturing)
    The decentralized production associated with material extrusion additive manufacture (MEX) has been proposed as an ideal path to increase the circularity of plastics through direct recycling. Although multiple studies have reported on the 3D printing of various recycled plastics, variability in recycled materials, in particular post-consumer waste, challenges the direct extension of these results into production through MEX. Here, we demonstrate filament fabrication and printing of post-consumer polypropylene (PP), where the PP is sourced from clear, cold drink cups from three large international food service and beverage retail chains to provide well defined plastic waste that is perfectly sorted for recycling. These sources for the recycled PP were selected due to their ready availability to enable the results to be directly applied for hobbyist printing, blow molded products to provide good mechanical performance, and the clarity of the PP that suggests formulation design to minimize the PP crystal size. Despite the similarities in the end use product and their physical appearance, the source for the PP impacted the mechanical properties and the visual appearance of the printed objects. These differences can be directly traced to the rheological properties and oxidative stability of the PP at conditions relevant with the print process. These results clearly illustrate differences in initial formulation design and branding details, even when the product is for the same application, impacts the performance of recycled plastics in AM. The high viscosity associated with the PP from blow molding leads to requirements for higher extrusion temperatures for printing. The combination of high temperature and shear during extrusion process of 3D printing degrades the recycled PP. For circularity with MEX with recycled PP, one needs to consider the evolution in the properties of the polymer. Rheological details of recycled plastics are critical to selection of processing conditions and performance of MEX parts. Reporting of rheological data of recycled plastics and these properties after printing is critical to enable translation towards circular 3D printing of recycled plastics. 
    more » « less
  3. ; ; (, ACM)
    Multi-material 3D printing combines the functional properties of different materials (e.g., mechanical, electrical, color) within a single object that is fabricated without manual assembly. However, this presents sustainability challenges as multi-material objects cannot be easily recycled. Because each material has a different processing temperature, considerable effort must be used to separate them for recycling. This paper presents a computational fabrication technique to generate dissolvable interfaces between different materials in a 3D printed object without affecting the object’s intended use. When the interfaces are dissolved, the object is disassembled to enable recycling of the individual materials. We describe the computational design of these interfaces alongside experimental evaluations of their strength and water solubility. Finally, we demonstrate our technique across 9 multi-material 3D printed objects of varying structural and functional complexity. Our technique enables us to recycle 89.97% of the total mass of these objects, promoting greater sustainability in 3D printing. 
    more » « less
  4. ; ; (, Journal of Polymer Science)
    Abstract Environmental contamination by plastic waste is a growing threat to the environment and human health. Unfortunately, most post‐consumer plastics are still disposed of in landfills, even plastics that could be easily recycled via simple chemical processes. This disconnect between technology and implementation is partly due to the economic barrier posed by multi‐step processes that convert plastic waste into commodity goods. There is an urgent need for green methods to convert plastic waste directly into marketable commodities via simple processes. Herein we report a simple, single‐stage process to chemically recycle poly(ethylene terephthalate) (PET) to yield composites having thermal and mechanical properties that are competitive with commercial structural materials like Portland cement. In this protocol, a mixture of PET and geraniol are heated with elemental sulfur. In this process, transesterification between geraniol and PET with concomitant thiocracking of the PET backbone leads to the formation of a highly‐crosslinked sulfur–PET–geraniol (SPG) network composite. The composite exhibited compressive strength (23.1 MPa) greater than that required for Portland cement to be used in building foundations. This new, single‐stage chemical recycling strategy thus employs a bio‐olefin and waste sulfur to convert PET waste into a durable composite that could serve as a sustainable alternative to traditional cements. 
    more » « less
  5. ; ; ; ; ; ; ; (, Journal of Applied Polymer Science)
    Abstract The chemically crosslinked network structures make epoxies, the most common thermosets, unable or hard to be recycled, causing environmental problems and economic losses. Epoxy‐based vitrimers, polymer networks deriving from epoxy resins, can be thermally malleable according to bond exchange reactions (BERs), opening the door to recycle epoxy thermosets. Here a series of experiments were carried out to study the effects of processing conditions (such as particle size distributions, temperature, time, and pressure) on recycling of an epoxy‐anhydride vitrimer. Polymer powders from the epoxy‐anhydride vitrimer with different size distributions were prepared and characterized, and the influence of particle size on the mechanical performance of recycled epoxy‐anhydride vitrimers was investigated by dynamic mechanical analysis and uniaxial tensile test. Experimental results demonstrated that finer polymer powders can increase the contacting surfaces of recycled materials and thus result in high quality of recycled materials. In addition, the influences of other treating parameters, such as temperature, time, and pressure, were also discussed in this study. Adjusting these treating parameters can help the design of an optimized reprocessing procedure to meet practical engineering applications. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email