Search for: All records

Reversible lithium metal anodes (LMAs) are the holy grail for future rechargeable lithium metal batteries. Threedimensional (3-D) conductive hosts have been extensively explored as an effective approach to suppressing dendrite formation and enabling reversible Li plating/stripping. However, the microscopic morphologies of Li plating and their correlation with the cell performance are not clear. Herein we unravel these issues using the vertically aligned carbon nanofiber (VACNF) array as a model 3-D conductive carbon host which has a welldefined vertical low-tortuosity structure allowing observation of the intrinsic Li morphologies infiltrated into the 3-D host. The VACNF array indeed provides much higher stability and reversibility for Li plating/stripping due to its high surface area and lithiophilic properties. We found that Li plating on both VACNF array and planar Cu electrodes follows the classical nucleation and growth model. Though the low plating current density (≤0.10 mA/cm2) provides better cycling stability consistent with the Sand’s equation, it forms sparse irregular grains stacked with dendrite-like long Li fibers. In contrast, the moderate to high plating current densities (1.0 - 5.0 mA/cm2) produce more uniform Li morphologies consisting of smaller micro-columns or micro-spheres. By decoupling the plating and stripping current densities, we unravel that the more uniform micro-columnar Li infiltrated in the VACNF array obtained at the moderate plating current density (~1.0 mA/cm2) indeed exhibits the highest cycling performance. This provides new insights into the relationship between macroscopic electrochemical tests and microscopic Li morphologies, aiding in optimizing the performance of LMAs based on 3-D conductive hosts. 

Amorphous molybdenum sulfide (a-MoS3) is a promising non-precious electrocatalyst for hydrogen evolution reaction owing to the abundant defective active sites. Here in, we show a rapid microwave-assisted synthesis method to produce a-MoS3 catalysts on reduced graphene oxide (rGO) substrates. The a-MoS3 reported in this study comprise of two possible 1D chain-like structures, i.e., with molybdenum (IV) in Weber’s model and molybdenum (V) in Hibble’s model, unlike the polymeric cluster type a-MoS3 structures reported in literature. Thermal annealing of the microwave-prepared a-MoS3 produced a family of defect-engineered MoSx/rGO hybrids, from a-MoS3 to crystalline MoS2, which showed tunable HER activities. XPS analysis provided in-depth understanding of the compositional changes in MoSx/rGO with thermal annealing. The a-MoS3/rGO 250 (annealed at 250 ◦C) exhibited the highest HER catalytic activity among all the MoSx/rGO hybrids, with an overpotential of 208 mV at 10 mA/cm2, a low Tafel slope of 52 mV/decade, a high double layer capacitance of 3.7 mF/cm2 and a high TOF value of 0.43 H2/s per site at the HER overpotential of 208 mV. The excellent HER activity is attributed to both MoV and sulfur active sites. This study provides a controllable, scalable and rapid synthesis method to produce 1D chain-like a-MoS3 structures for HER electrocatalysis. 

Nitrogen doping in carbon materials can modify the employed carbon material’s electronic and structural properties, which helps in creating a stronger metal-support interaction. In this study, the role of nitrogen doping in improving the durability of Pt catalysts supported on a three-dimensional vertically aligned carbon nanofiber (VACNF) array towards oxygen reduction reaction (ORR) was explored. The nitrogen moieties present in the N-VACNF enhanced the metal-support interaction and contributed to a reduction in the Pt particle size from 3.1 nm to 2.3 nm. The Pt/N-VACNF catalyst showed better durability when compared to Pt/VACNF and Pt/C catalysts with similar Pt loading. DFT calculations validated the increase in the durability of the Pt NPs with an increase in pyridinic N and corroborated the molecular ORR pathway for Pt/N-VACNF. Moreover, the Pt/N-VACNF catalyst was found to have excellent tolerance towards methanol crossover. 

This study reports the preparation of a set of hybrid materials consisting of molybdenum disulfide (MoS 2 ) nanopatches on reduced graphene oxide (rGO) nanosheets by microwave specific heating of graphene oxide and molecular molybdenum precursors followed by thermal annealing in 3% H 2 and 97% Ar. The microwave process converts graphene oxide to ordered rGO nanosheets that are sandwiched between uniform thin layers of amorphous molybdenum trisulfide (MoS 3 ). The subsequent thermal annealing converts the intermediate layers into MoS 2 nanopatches with two-dimensional layered structures whose defect density is tunable by controlling the annealing temperature at 250, 325 and 600 °C, respectively. All three MoS 2 /rGO samples and the MoS 3 /rGO intermediate after the microwave step show a high Li-ion intercalation capacity in the initial 10 cycles (over 519 mA h g MoSx −1 , ∼3.1 Li + ions per MoS 2 ) which is attributed to the small MoS 2 nanopatches in the MoS 2 /rGO hybrids while the effect of further S-rich defects is insignificant. In contrast, the Zn-ion storage properties strongly depend on the defects in the MoS 2 nanopatches. The highly defective MoS 2 /rGO hybrid prepared by annealing at 250 °C shows the highest initial Zn-ion storage capacity (∼300 mA h g MoSx −1 ) and close to 100% coulombic efficiency, which is dominated by pseudocapacitive surface reactions at the edges or defects in the MoS 2 nanopatches. The fast fading in the initial cycles can be mitigated by applying higher charge/discharge currents or extended cycles. This study validates that defect engineering is critical for improving Zn-ion storage. 

Abstract Nitrogen‐doped graphitic carbon materials have been widely used as a catalyst support in the methanol oxidation reaction (MOR). In this study, we report the role of three‐dimensionally architectured in‐situ N‐doped vertically aligned carbon nanofibers (VACNF) as a catalyst support for MOR in acidic and alkaline media. The abundant graphitic edge sites at the sidewall of N‐doped VACNF strongly anchor the deposited platinum group metal (PGM) catalysts and induce a partial electron transfer between the PGM catalysts and support. Density Functional Theory (DFT) calculations reveal that the strong metal‐support interaction substantially increases the adsorption energy of OH, particularly near the N‐doping sites, which helps to compete and remove the adsorbed intermediate species generated during MOR. The PGM catalysts on N‐doped VACNF support exhibits CO stripping at lower potentials comparing to the commercial Vulcan carbon support and presents an enhanced electrocatalytic performance and better durability for MOR.