Microwave heating methods offer unique advantages in preparations of inorganic solids due to the high heating rates, potentially selective heating, and time/energy reductions. Understanding of these enhancements as well as involved mechanisms is poor due to the lack of available and easily applicable in situ monitoring methods, particularly for samples in the solid state. Existing in situ studies typically rely on access to beamline facilities as well as custom‐built microwave systems, which is in the best case inconvenient and in the worst case not achievable. In situ Raman spectroscopy is an ideal technique as it provides rapid and unambiguous phase identification by a noncontact method. Further, the instrument components are simple and compact, facilitating use in the typical synthetic laboratory. Only a few reports on using Raman spectroscopy for in situ measurements during microwave heating exist, and they all utilize specialized custom reactor setups. In this work, a new Raman measurement system designed to observe inorganic transformations in situ that is readily deployable in a standard, commercially available laboratory scale microwave reactor is described. As a simple demonstration, the anatase‐to‐rutile phase transition in TiO2is monitored under both microwave and conventional furnace heating. The excellent time resolution achieved demonstrates the utility of the system in understanding microwave‐assisted methods for the preparation of inorganic compounds. The simplicity will encourage integration by the non‐specialist to understand microwave heating for synthetic preparations and promote wider application of the technique.
The coordinated, cooperative use of microwave heating with conventional heating can provide advantages in chemical synthesis. Here, heterogeneous mixtures comprising ionic, highly microwave‐absorbing organic reagents and nearly microwave‐transparent arene solvents are heated conventionally and/or with microwaves, resulting in faster and, in some cases, higher yielding reactions when the two heating methods are applied cooperatively as compared to either method independently. Control experiments in more polar arene solvents show no advantage of cooperative heating, consistent with selective microwave heating phenomena. The experiments are facilitated by reactor technology that regulates internal reaction temperature and coordinates the application of conventional and microwave heating. The positive outcomes in this initial exploratory system suggest that cooperative heating can offer benefits in other systems designed for selective microwave heating.
more » « less- Award ID(s):
- 1665029
- NSF-PAR ID:
- 10154710
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Asian Journal of Organic Chemistry
- Volume:
- 9
- Issue:
- 6
- ISSN:
- 2193-5807
- Page Range / eLocation ID:
- p. 961-966
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Microwave (MW) heating is more effective than conventional (CONV) heating for promoting a high‐temperature oxidative cycloisomerization reaction that was previously reported as a key step in a total synthesis of the natural product illudinine. The thermal reaction pathway as envisioned is an inverse electron‐demand dehydro‐Diels–Alder reaction with in situ oxidation to generate a substituted isoquinoline, which itself is unstable to the reaction conditions. Observed reaction yields were higher at a measured bulk temperature of 200 °C than at 180 °C or 220 °C; at 24 hours than at earlier or later time points; and when the reaction solution was heated using MW energy as opposed to CONV heating with a metal heat block. Selective MW heating of polar solute aggregates is postulated to explain these observations.
-
more » « less
Abstract Cationic polymers are an interesting class of macromolecules due to their versatility and emerging properties that can be used for various industrial and biomedical purposes. This report is focused on investigating the use of microwave heating in the reversible addition–fragmentation chain transfer polymerization of functional cationic monomers,
N ‐(3‐aminopropyl)methacrylamide hydrochloride (APMA) andN ‐[3‐(dimethylamino)propyl]methacrylamide (DMAPMA). Under comparable polymerization reaction conditions, the microwave‐assisted reaction achieves up to 270% (APMA) and 375% (DMAPMA) rate enhancement over conventional oil‐bath mediated set‐up. Linear relationships are observed between number average molecular weight and monomer conversion for different target degrees of polymerization to give low‐ to high‐molecular‐weight cationic polymers. Chain extension experiments show increase in molecular weight of the cationic polymers with narrow dispersities (Ð < 1.2) indicating retention of the chain transfer agent with no observable aminolysis or hydrolysis during polymerization. -
more » « less
Abstract Using microwave irradiation, PtCo alloy nanoparticles were deposited within a few minutes on COOH‐functionalized MWCNT supports. The obtained catalysts were used for selective hydrogenation of cinnamaldehyde, a reaction whose products are widely used in various fields. In the selective cinnamaldehyde hydrogenation to cinnamyl alcohol, microwave‐prepared catalysts (generically, PtxCoy‐MW) outperformed a catalyst prepared by the conventional method (Pt1Co2‐con). The highest selective hydrogenation to cinnamyl alcohol, 89%, was obtained using Pt1Co2‐MW, while Pt1Co2‐con showed a selectivity of 76%. Characterization results confirmed that the microwave prepared samples had a stronger interaction between Pt and Co than that in the Pt1Co2‐con sample. The alloyed Co altered the electronic structure of Pt, leading to favorable adsorption of the C=O bond by the lone‐pair electrons of its oxygen atom. Moreover, the Pt1Co2‐MW sample showed neglectable change in catalytic performance (e. g., cinnamaldehyde conversion and selective hydrogenation to cinnamyl alcohol) during recycling experiments.
-
more » « less
Abstract Lyophilization is a common unit operation in pharmaceutical manufacturing but is a prolonged vacuum drying process with poor energy utilization. Microwave-assisted vacuum drying has been investigated to accelerate the lyophilization process. However, the literature lacks methodical approaches that consider the lyophilizer, the lyophilizate, the microwave power uniformity, the resulting heat uniformity, and the scalability. We present a microwave–vacuum drying method based on the statistical electromagnetics theory. The method offers an optimum frequency selection procedure that accounts for the lyophilizer and the lyophilizate. The 2.45 GHz frequency conventionally utilized is proven to be far from optimum. The method is applied in a microwave-assisted heating configuration to pharmaceutical excipients (sucrose and mannitol) and different myoglobin formulations in a lab-scale lyophilizer. At 18 GHz frequency and 60 W microwave power, the method shows nearly three times speed-up in the primary drying stage of sucrose relative to the conventional lyophilization cycle for typical laboratory batches. The uniformity of the microwave power inside the chamber is controlled within ± 1 dB. The resulting heating uniformity measured through residual moisture analysis shows 12.7% of normalized SD of moisture level across the batch in a microwave-assisted cycle as opposed to 15.3% in the conventional cycle. Conventional and microwave lyophilized formulations are characterized using solid-state hydrogen-deuterium exchange-mass spectrometry (ssHDX-MS), solid-state Fourier transform infrared spectroscopy (ssFTIR), circular dichroism (CD), and accelerated stability testing (AST). Characterization shows comparable protein structure and stability. Heat and mass transfer simulations quantify further effects of optimal volumetric heating via the high-frequency statistical microwave heating.
