An official website of the United States government
Abstract Based on observations from nature, tails are believed to help animals achieve highly agile motions. Traditional single-link robotic tails serve as a good simplification for both modeling and implementation purposes. However, this approach cannot explain the complicated tail behaviors exhibited in nature where multi-link structures are more commonly observed. Unlike its single-link counterpart, articulated multi-link tails essentially belong to the serial manipulator family which possesses special motion transmission design challenges. To address this challenge, a cable-driven hyper-redundant design becomes the most used approach. Limited by cable strength and elastic components, this approach suffers from low-frequency response, inadequate generated inertial loading, and fragile hardware, which are all critical drawbacks for robotic tails design. To solve these structure-related shortcomings, a multi-link robotic tail made up of rigid links is proposed in this paper. The new structure takes advantage of the traditional hybrid mechanism architecture, but utilizes rigid mechanisms to couple the motions between the ith link and the (i + 1)th link rather than using cable actuation. By doing so, the overall tail becomes a rigid mechanism that achieves quasi-uniform spatial bending for each segment and allows performing highly dynamic motions. The mechanism and detailed design of this new robotic tail are presented. The kinematic model was developed and an optimization process was conducted to reduce the bending non-uniformity for the rigid tail. Based on this special optimization design, the dynamic model of the new mechanism is significantly simplified. A small-scale three-segment prototype was integrated to verify the proposed mechanism's unique mobility.
more »
« less
Design, Analysis, and Optimization of a New Two-DOF Articulated Multi-Link Robotic Tail
Based on observations from nature, tails are believed to help animals achieve highly agile motions. Traditional single-link robotic tails serve as a good simplification for both modeling and implementation purposes. However, this approach cannot explain the complicated tail behaviors exhibited in nature where multi-link structures are more commonly observed. Unlike its single-link counterpart, articulated multi-link tails essentially belong to the serial manipulator family which possesses special transmission design challenges. To address this challenge, a cable driven hyper-redundant design becomes the most used approach. Limited by cable strength and elastic components, this approach suffers from low frequency responses, inadequate generated inertial loading, and fragile hardware, which are all critical drawbacks for robotic tails design. To solve these structure related shortcomings, a multi-link robotic tail made up of rigid links is proposed in this paper. The new structure takes advantage of the traditional hybrid mechanism architecture, but utilizes rigid mechanisms to couple the motions between ith link and i + 1th link rather than using cable actuation. By doing so, the overall tail becomes a rigid mechanism which achieves quasi-uniform spatial bending for each segment and allows performing highly dynamic motions. The mechanism and detailed design for this new tail are synthesized. The kinematic model was developed and an optimization process was conducted to minimize the bending non-uniformity for the rigid tail.
more »
« less
- Award ID(s):
- 1906727
- PAR ID:
- 10155508
- Date Published:
- Journal Name:
- Proceedings of the ASME 2019 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC/CIE), 43rd Mechanisms & Robotics Conference
- Volume:
- 5B
- Page Range / eLocation ID:
- V05BT07A008
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This paper presents the development of a new robotic tail based on a novel cable-driven universal joint mechanism. The novel joint mechanism is synthesized by geometric reasoning to achieve the desired cable length invariance property, wherein the mechanism maintains a constant length for the driving cables under universal rotation. This feature is preferable because it allows for the bidirectional pulling of the cables which reduces the requisite number of actuators. After obtaining this new joint mechanism, a serpentine robotic tail with fewer actuators, simpler controls, and a more robust structure is designed and integrated. The new tail includes two independent macro segments (2 degrees of freedom each) to generate more complex shapes (4 degrees of freedom total), which helps with improving the dexterity and versatility of the robot. In addition, the pitch bending and yaw bending of the tail are decoupled due to the perpendicular joint axes. The kinematic modeling, dynamic modeling, and workspace analysis are then explained for the new robotic tail. Three experiments focusing on statics, dynamics, and dexterity are conducted to validate the mechanism and evaluate the new robotic tail's performance.more » « less
-
ABSTRACT IntroductionThe intervertebral disc (IVD) of the bovine tail is a commonly used research analogue for the human disc at the organ, tissue, and cellular levels. While these tails are subjected to thousands of dynamic motion events daily, little is known about how these motions might induce tissue remodeling, particularly in the outer annulus fibrosus (AF) of IVDs connecting adjacent vertebrae. This study hypothesized that despite the similarities in geometry and biochemical composition of IVDs in the bovine tail, level‐wise variations in repetitive in‐vivo motion would be associated with tissue level adaptations. MethodsIn‐vivo active range of motion (RoM) was measured by placing inertial measurement unit sensors on the tails of adult cows and using a multi‐segment rigid body model to calculate level‐wise flexion‐extension and lateral bending angles. Level‐wise passive RoM was measured from cadaveric adult bovine tails in flexion, extension, and lateral bending with skin and muscles removed. IVDs were extracted for measurement of height, diameters, AF radial thicknesses, and AF fiber crimp periods. ResultsIn‐vivo joint RoM was found to vary drastically by level, largely due to a prominent second order mode with inflection point at the fourth joint. Joint levels near this inflection point were found to have the highest passive RoMs. In the proximal tail, decreased RoM was associated with an increased fiber crimp period in the outer AF, while in the distal tail it was associated with increased AF thickness. DiscussionTaken together, these findings suggest that IVDs in the bovine tail respond to repeated complex dynamic motions through a process of adaptation at the mesoscale (AF thickening during growth) and microscale (residual strain accumulation in the mature state). The bovine tail thus provides a powerful tool for modeling how the human lumbar intervertebral disc may remodel in response to changes in exposure to repetitive motions.more » « less
-
Inspired by the embodied intelligence observed in octopus arms, we introduce magnetically controlled origami robotic arms based on Kresling patterns for multimodal deformations, including stretching, folding, omnidirectional bending, and twisting. The highly integrated motion of the robotic arms is attributed to inherent features of the reconfigurable Kresling unit, whose controllable bistable deploying/folding and omnidirectional bending are achieved through precise magnetic actuation. We investigate single- and multiple-unit robotic systems, the latter exhibiting higher biomimetic resemblance to octopus’ arms. We start from the single Kresling unit to delineate the working mechanism of the magnetic actuation for deploying/folding and bending. The two-unit Kresling assembly demonstrates the basic integrated motion that combines omnidirectional bending with deploying. The four-unit Kresling assembly constitutes a robotic arm with a larger omnidirectional bending angle and stretchability. With the foundation of the basic integrated motion, scalability of Kresling assemblies is demonstrated through distributed magnetic actuation of double-digit number of units, which enables robotic arms with sophisticated motions, such as continuous stretching and contracting, reconfigurable bending, and multiaxis twisting. Such complex motions allow for functions mimicking octopus arms that grasp and manipulate objects. The Kresling robotic arm with noncontact actuation provides a distinctive mechanism for applications that require synergistic robotic motions for navigation, sensing, and interaction with objects in environments with limited or constrained access. Based on small-scale Kresling robotic arms, miniaturized medical devices, such as tubes and catheters, can be developed in conjunction with endoscopy, intubation, and catheterization procedures using functionalities of object manipulation and motion under remote control.more » « less
-
Abstract Until recently, most four-legged robots have lacked a feature that is found again and again in nature—a tail. Studies of animal locomotion and robots in the laboratory indicate that leaving out tails has been a design drawback. In fact, research conducted by our lab at Virginia Tech has shown that an articulated robotic tail can effectively maneuver and stabilize a quadruped both for static and dynamic locomotion.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1115/DETC2019-97537
