skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Effects of Air Cavity in Dynamic Pressure Sensors: Experimental Validation
An air-backed diaphragm is the key structure of most dynamic pressure sensors and plays a critical role in determining the sensor performance. Our previous analytical model investigated the influence of air cavity length on the sensitivity and bandwidth. The model found that as the cavity length decreases, the static sensitivity monotonically decreases, and the fundamental natural frequency shows a three-stage trend: increasing in the long-cavity-length range, reaching a plateau value in the medium-cavity-length range, and decreasing in the short-cavity-length range, which cannot be captured by the widely used lumped model. In this study, we conducted the first experimental measurements to validate these findings. Pressure sensors with a circular polyimide diaphragm and a backing air cavity with an adjustable length were designed, fabricated, and characterized, from which the static sensitivities and fundamental natural frequencies were obtained as a function of the cavity length. A further parametric study was conducted by changing the in-plane tension in the diaphragm. A finite element model was developed in COMSOL to investigate the effects of thermoviscous damping and provide validation for the experimental study. Along with the analytical model, this study provides a new understanding and important design guidelines for dynamic pressure sensors with air-backed diaphragms.  more » « less
Award ID(s):
1663135
PAR ID:
10163556
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
Sensors
Volume:
20
Issue:
6
ISSN:
1424-8220
Page Range / eLocation ID:
1759
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, 15th International Manufacturing Science and Engineering Conference)
    The objective of this paper is to demonstrate the flexure properties of ABS plastic in a 3D printed object as a process to enable embedded pressure sensing capabilities. Developing the potential for non-static 3D parts broadens the scope of the fused deposition modeling (FDM) process to include printing ‘smart’ objects that utilize intrinsic material properties to act as microphones, load sensors, accelerometers, etc. In order to demonstrate a strain-based pressure transducer, strain gauges were embedded either directly on top or in the middle of a flexible ABS diaphragm. Securing a strain gage directly on top of the diaphragm traced a reference pressure more closely than diaphragms with the strain gage embedded halfway into the diaphragm. To prevent temperature-related drift, an additional strain gage was suspended above the secured gage, inside the 3D printed cavity. The additional gage allowed for a half-bridge circuit in lieu of a quarter-bridge circuit, which minimized drift due to temperature change. The ABS diaphragm showed no significant signs of elastic hysteresis or nonlinear buckling. When sealed with 100% acetone, the diaphragm leaked ∼50x slower than as-printed sensors. After pressurizing and depressurizing the devices multiple times, they output pressure readouts that were consistent and repeatable for any given pressure within the operational range of 0 to 7psi. The repeatability of each of the final generation sensors indicates that ‘smart’ objects printed using an FDM process could be individually calibrated to make repeatable recordings. This work demonstrates a concept overlooked previous to now — FDM printed objects are not limited to static models, which lack dynamic motion of the part as an element of design. Altering FDM’s bottom-up process can allow for easily embedding sensing elements that result in printed objects which are functional on the mesoscale. 
    more » « less
  2. ; ; ; (, Proceedings of the ASME 2020 International Mechanical Engineering Congress and Exposition (IMECE))
    null (Ed.)
    Membrane-based acoustic metamaterials have been reported to achieve 100% absorption, the acoustic analogue of photonic black-hole. However, the bandwidth is usually very narrow around some local resonance frequency, which limits its practical use. To address this limitation and achieve a broadband absorption, this paper first establishes a theoretical framework for unit cells of air-backed diaphragms, modeled as an equivalent mass-spring-dashpot system. Based on the impedance match principle, three different approaches are numerically investigated by tuning the cavity length, the static pressure in the cavity, and the effective damping of perforated plates. A prototype with polyimide diaphragm and 3D printed substrate is then fabricated and characterized using an acoustic impedance tube. Preliminary experiments show the feasibility to achieve an absorption bandwidth of ∼200 Hz at center frequency of 1.45 kHz. This work pays the way for developing a sub-wavelength light weight broadband acoustic absorber for a variety of applications in noise control. 
    more » « less
  3. ; ; (, ASME Fluids Engineering Division Summer Meeting FEDSM2021)
    Hydrodynamic performance of ships can be greatly improved by the formation of air cavities under ship bottom with the purpose to decrease water friction on the hull surface. The air-cavity ships using this type of drag reduction are usually designed for and typically effective only in a relatively narrow range of speeds and hull attitudes and sufficient rates of air supply to the cavity. To investigate the behavior of a small-scale air-cavity boat operating under both favorable and detrimental loading and speed conditions, a remotely controlled model hull was equipped with a data acquisition system, video camera and onboard sensors to measure air-cavity characteristics, air supply rate and the boat speed, thrust and trim in operations on open-water reservoirs. These measurements were captured by a data logger and also wirelessly transmitted to a ground station and video monitor. The experimental air-cavity boat was tested in a range of speeds corresponding to length Froude numbers between 0.17 and 0.5 under three loading conditions, resulting in near zero trim and significant bow-up and bow-down trim angles at rest. Reduced cavity size and significantly increased drag occurred when operating at higher speeds, especially in the bow-up trim condition. The other objective of this study was to determine whether computational fluid dynamics simulations can adequately capture the recorded behavior of the boat and air cavity. A computational software Star-CCM+ was utilized with the VOF method employed for multi-phase flow, RANS approach for turbulence modeling, and economical mesh settings with refinements in the cavity region and near free surface. Upon conducting the mesh verification study, several experimental conditions were simulated, and approximate agreement with measured test data was found. Adaptive mesh refinement and time step controls were also applied to compare results with those obtained on the user-generated mesh. Adaptive controls improved resolution of complex shedding patterns from the air cavity but had little impact on overall results. The presented here experimental approach and obtained results indicate that both outdoor experimentation and computationally inexpensive modeling can be used in the process of developing air-cavity systems for ship hulls. 
    more » « less
  4. ; ; ; ; ; ; ; (, APL Bioengineering)
    In this work, we describe a benchtop model that recreates the motion and function of the diaphragm using a combination of advanced robotic and organic tissue. First, we build a high-fidelity anthropomorphic model of the diaphragm using thermoplastic and elastomeric material based on clinical imaging data. We then attach pneumatic artificial muscles to this elastomeric diaphragm, pre-programmed to move in a clinically relevant manner when pressurized. By inserting this diaphragm as the divider between two chambers in a benchtop model—one representing the thorax and the other the abdomen—and subsequently activating the diaphragm, we can recreate the pressure changes that cause lungs to inflate and deflate during regular breathing. Insertion of organic lungs in the thoracic cavity demonstrates this inflation and deflation in response to the pressures generated by our robotic diaphragm. By tailoring the input pressures and timing, we can represent different breathing motions and disease states. We instrument the model with multiple sensors to measure pressures, volumes, and flows and display these data in real-time, allowing the user to vary inputs such as the breathing rate and compliance of various components, and so they can observe and measure the downstream effect of changing these parameters. In this way, the model elucidates fundamental physiological concepts and can demonstrate pathology and the interplay of components of the respiratory system. This model will serve as an innovative and effective pedagogical tool for educating students on respiratory physiology and pathology in a user-controlled, interactive manner. It will also serve as an anatomically and physiologically accurate testbed for devices or pleural sealants that reside in the thoracic cavity, representing a vast improvement over existing models and ultimately reducing the requirement for testing these technologies in animal models. Finally, it will act as an impactful visualization tool for educating and engaging the broader community. 
    more » « less
  5. ; ; ; (, Smart Materials and Structures)
    Engineered Ionic Polymer Metal Composites (eIPMCs) represent the next generation of IPMCs, soft electro-chemo-mechanically coupled smart materials used as actuators and sensors. Recent studies indicate that eIPMC sensors, featuring unique microstructures at the interface between the ionic polymer membrane and the electrode, exhibit enhanced electrochemical behavior and sensitivity under compression, as compared to traditional IPMCs. However, a complete and experimentally-validated model of how eIPMCs behave under dynamic compression loads is currently missing. In this paper, we develop an analytical model for eIPMC sensors, elucidating the role of the engineered interface, modeled as a separate material layer with unique mechanical and electrochemical properties. Theoretical predictions focus on the mechanical-to-electrochemical transduction response under dynamic compressive loads. Experimental verification is conducted on conventional IPMC and novel eIPMC samples fabricated using the polymer abrading technique. Electrochemical impedance spectroscopy is performed to study the effect of the engineered interface on the electrochemical properties. Open-circuit (OC) voltage and short-circuit (SC) current are measured under external compressive loads in different loading scenarios to demonstrate sensing performance. Results show good qualitative agreement between experimental trends and model predictions. Experiments over the frequency range 1-18 Hz demonstrate an increase of 220%-290% in open-circuit voltage and 17%-166% in SC current sensitivity for eIPMCs over IPMCs. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email