An official website of the United States government
Multirotor configurations introduce complicated aerodynamic and aeroacoustic interactions that must be considered during aircraft design. In this paper we explore two numerical methods to model the acoustic noise caused by aerodynamic rotor-on-rotor interactions of rotors in hover. The first method uses a conventional mesh-based unsteady Reynolds-average Navier-Stokes (URANS) solver, while the second consists of a meshless Lagrangian solver based on the viscous vortex particle method (VPM). Both methods are coupled with an aeroacoustics solver for tonal and broadband noise predictions. Noise predictions are validated for single and multi-rotor configurations, obtaining with the VPM a similar accuracy than URANS while being two orders of magnitude faster. We characterize the interactions of two side-by-side rotors in hover as the tip-to-tip distance and downstream spacing are varied. At an observer located six diameters away, multirotor noise is the strongest above and below the rotors, increasing by about 10 dBA directly underneath as the rotors are brought closer together. The interactions show no sensitivity to blade loading distribution, indicating that multirotor interactions are not alleviated with a lighter tip loading. We found that noise can be mitigated by spacing the rotors in the downstream direction—with the optimal spacing being about half a diameter—achieving a noise decrease of about 4 dBA without any aerodynamic penalties.
more »
« less
Multirotor Trim using Loose Aerodynamic Coupling
A multirotor trim module is developed for the HPCMP CREATETM-AV Helios rotorcraft simulation code. Trimmed free-flight simulation results are presented for two multirotor configurations, using rotor frequencies and aircraft attitudes as the control variables. The loose-coupling procedure is used to achieve trim, where aerodynamic loading on the rotor blades and fuselage are computed using a simplified aerodynamic model, and modified at each coupling iteration using the airloads computed by the higher fidelity CFD based aerodynamics. Two different optimization methods are tested: a least-square regression algorithm, with the norm of the loads at the center of gravity as the objective function, and a nonlinear constrained optimization code, with the total power as the objective function, and with constraints applied to satisfy trim. First, a commercial small-scale UAV is simulated in forward flight. A reference model for midscale UAM applications is then trimmed in hover to demonstrate the module’s ability to model and trim a complex configuration.
more »
« less
- Award ID(s):
- 1728277
- PAR ID:
- 10179923
- Date Published:
- Journal Name:
- VFS Aeromechanics for Advanced Vertical Flight Technical Meeting
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Multirotor configurations introduce complicated aerodynamic and aeroacoustic interactions that must be considered during aircraft design. In this paper we explore two numerical methods to model the acoustic noise caused by aerodynamic rotor-on-rotor interactions of rotors in hover. The first method uses a conventional mesh-based unsteady Reynolds-average Navier-Stokes (URANS) solver, while the second consists of a meshless Lagrangian solver based on the viscous vortex particle method (VPM). Both methods are coupled with an aeroacoustics solver for tonal and broadband noise predictions. Noise predictions are validated for single and multi-rotor configurations, obtaining with the VPM a similar accuracy than URANS while being two orders of magnitude faster. We characterize the interactions of two side-by-side rotors in hover as the tip-to-tip distance and downstream spacing are varied. At an observer located six diameters away, multirotor noise is the strongest above and below the rotors, increasing by about 10 dBA directly underneath as the rotors are brought closer together. The interactions show no sensitivity to blade loading distribution, indicating that multirotor interactions are not alleviated with a lighter tip loading. We found that noise can be mitigated by spacing the rotors in the downstream direction—with the optimal spacing being about half a diameter—achieving a noise decrease of about 4 dBA without any aerodynamic penalties.more » « less
-
Aeromechanics of highly flexible flapping wings is a complex nonlinear fluid–structure interaction problem and, therefore, cannot be analyzed using conventional linear aeroelasticity methods. This paper presents a standalone coupled aeroelastic framework for highly flexible flapping wings in hover for micro air vehicle (MAV) applications. The MAV-scale flapping wing structure is modeled using fully nonlinear beam and shell finite elements. A potential-flow-based unsteady aerodynamic model is then coupled with the structural model to generate the coupled aeroelastic framework. Both the structural and aerodynamic models are validated independently before coupling. Instantaneous lift force and wing deflection predictions from the coupled aeroelastic simulations are compared with the force and deflection measurements (using digital image correlation) obtained from in-house flapping wing experiments at both moderate (13 Hz) and high (20 Hz) flapping frequencies. Coupled trim analysis is then performed by simultaneously solving wing response equations and vehicle trim equations until trim controls, wing elastic response, inflow and circulation converge all together. The dependence of control inputs on weight and center of gravity (cg) location of the vehicle is studied for the hovering flight case.more » « less
-
Abstract Recent interest in urban and regional air mobility and the need to improve the aviation industry’s emissions has motivated research and development of novel propeller-driven vehicles. These vehicles range in configuration from conventional takeoff and landing designs to complex rotorcraft that transition between vertical and horizontal flight. These designs must be optimized to ensure optimal efficiency throughout their missions, leveraging the tightly coupled nature of propeller-wing interaction. In this work, we study the NASA tiltwing concept vehicle wing with varying numbers of propellers, ranging from no propellers to five propellers evenly spaced along the wing. Using aerodynamic shape optimization, we optimize the wing shapes for each propeller-wing configuration, minimizing the wing drag. These optimizations are carried out with DAFoam, a discrete adjoint implementation of OpenFOAM, embedded within OpenMDAO and the MPhys optimization framework. The optimizations show that the lowest drag configuration is a single propeller mounted at the wing tip. Increasing the number of propellers slightly increases drag compared to the single propeller configuration. However, aerodynamic shape optimization considering propeller-wing interaction yields a negligible benefit compared to aerodynamic optimization of an isolated wing that is subsequently trimmed to a desired flight condition in the presence of a propeller.more » « less
-
Birds perform astounding aerial maneuvers by actuating their shoulder, elbow, and wrist joints to morph their wing shape. This maneuverability is desirable for similar-sized uncrewed aerial vehicles (UAVs) and can be analyzed through the lens of dynamic flight stability. Quantifying avian dynamic stability is challenging as it is dictated by aerodynamics and inertia, which must both account for birds’ complex and variable morphology. To date, avian dynamic stability across flight conditions remains largely unknown. Here, we fill this gap by quantifying how a gull can use wing morphing to adjust its longitudinal dynamic response. We found that it was necessary to adjust the shoulder angle to achieve trimmed flight and that most trimmed configurations were longitudinally stable except for configurations with high wrist angles. Our results showed that as flight speed increases, the gull could fold or sweep its wings backward to trim. Further, a trimmed gull can use its wing joints to control the frequencies and damping ratios of the longitudinal oscillatory modes. We found a more damped phugoid mode than similar-sized UAVs, possibly reducing speed sensitivity to perturbations, such as gusts. Although most configurations had controllable short-period flying qualities, the heavily damped phugoid mode indicates a sluggish response to control inputs, which may be overcome while maneuvering by morphing into an unstable flight configuration. Our study shows that gulls use their shoulder, wrist, and elbow joints to negotiate trade-offs in stability and control and points the way forward for designing UAVs with avian-like maneuverability.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- The DOI is not currently available.
