Ni-rich Li(NixCoyMnz)O2 (x ≥ 0.8)-layered oxide materials are highly promising as cathode materials for high-energy-density lithium-ion batteries in electric and hybrid vehicles. However, their tendency to undergo side reactions with electrolytes and their structural instability during cyclic lithiation/delithiation impairs their electrochemical cycling performance, posing challenges for large-scale applications. This paper explores the application of an Al2O3 coating using an atomic layer deposition (ALD) system on Ni-enriched Li(Ni0.8Co0.1Mn0.1)O2 (NCM811) cathode material. Characterization techniques, including X-ray diffraction, scanning electron microscopy, and transmission electron microscopy, were used to assess the impact of alumina coating on the morphology and crystal structure of NCM811. The results confirmed that an ultrathin Al2O3 coating was achieved without altering the microstructure and lattice structure of NCM811. The alumina-coated NCM811 exhibited improved cycling stability and capacity retention in the voltage range of 2.8–4.5 V at a 1 C rate. Specifically, the capacity retention of the modified NCM811 was 5%, 9.11%, and 11.28% higher than the pristine material at operating voltages of 4.3, 4.4, and 4.5 V, respectively. This enhanced performance is attributed to reduced electrode–electrolyte interaction, leading to fewer side reactions and improved structural stability. Thus, NCM811@Al2O3 with this coating process emerges as a highly attractive candidate for high-capacity lithium-ion battery cathode materials.
- PAR ID:
- 10219107
- Date Published:
- Journal Name:
- Nanomaterials
- Volume:
- 10
- Issue:
- 9
- ISSN:
- 2079-4991
- Page Range / eLocation ID:
- 1870
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li+). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb2O5on single-crystal LiNi0.5Mn0.3Co0.2O2cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li4Ti5O12anodes and Nb2O5-coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li+). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb2O5coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.
-
more » « less
Abstract The instability of Nickel (Ni)‐rich cathodes at high voltage is a critical bottleneck toward developing superior lithium‐ion batteries. This instability is driven by cathode‐electrolyte side reactions, causing rapid degradation, and compromising the overall cycle life. In this study, a protective coating using dispersed “magnetite (FeO.Fe2O3)” nanoparticles is used to uniformly decorate the surface of LiNi0.8Co0.1Mn0.1O2(NMC 811) microparticles. The modified cathode delivers significant improvement in electrochemical performance at high voltage (≈4.6 V) by suppressing deleterious electrode–electrolyte interactions. A notably higher cycle stability, rate performance, and overall energy density is realized for the coated cathode in a conventional liquid electrolyte battery. When deployed in pellet‐stacked solid‐state cells with Li6PS5Cl as the electrolyte, the magnetite‐coated NMC 811 showed strikingly superior cycling stability than its uncoated counterpart, proving the versatility of the chemistry. The facile surfactant‐assisted coating process developed in this work, in conjunction with the affordability, abundance, and nontoxic nature of magnetite makes this a promising approach to realize commercially viable high voltage Ni‐rich cathodes that exhibit stable performance in liquid as well as solid‐state lithium‐ion batteries.
-
more » « less
The paper describes a heterobimetallic mixed-ligand hexanuclear precursor [NaMn2(thd)4(OAc)]2 (1) (thd = 2,2,6,6-tetramethyl-3,5-heptadionate; OAc = acetate) that was designed based on its lithium homoleptic analogue, [LiMn2(thd)5], by replacing one of the thd ligands with an acetate group in order to accommodate 5-coordinated sodium instead of tetrahedral lithium ion. The complex, which is highly volatile and soluble in a variety of common solvents, has been synthesized by both the solid-state and solution methods. The unique “dimer-of-trimers” heterometallic structure consists of two trinuclear [NaMnII2(thd)4]+ units firmly bridged by two acetate ligands. X-ray diffraction techniques, DART mass spectrometry, ICP-OES analysis, and IR spectroscopy have been employed to confirm the structure and composition of the hexanuclear complex. Similar to the Li counterpart forming LiMn2O4 spinel material upon thermal decomposition, the title Na:Mn = 1:2 compound was utilized as the first single-source precursor for the low-temperature preparation of Na4Mn9O18 tunnel oxide. Importantly, four Mn sites in the hexanuclear molecule can be potentially partially substituted by other transition metals, leading to heterotri- and tetrametallic precursors for the advanced quaternary and quinary Na-ion oxide cathode materials.
-
more » « less
Abstract The deposition of protective coatings on the spinel LiMn2O4(LMO) lithium‐ion battery cathode is effective in reducing Mn dissolution from the electrode surface. Although protective coatings positively affect LMO cycle life, much remains to be understood regarding the interface formed between these coatings and LMO. Using operando powder X‐ray diffraction with Rietveld refinement, it is shown that, in comparison to bare LMO, the lattice parameter of a model Au‐coated LMO cathode is significantly reduced upon relithiation. Less charge passes through Au‐coated LMO in comparison to bare LMO, suggesting that the reduced lattice parameter is associated with decreased Li+solubility in the Au‐coated LMO. Density functional theory calculations show that a more Li+‐deficient near‐surface is thermodynamically favorable in the presence of the Au coating, which may further stabilize these cathodes through suppressing formation of the Jahn–Teller distorted Li2Mn2O4phase at the surface. Electronic structure and chemical bonding analyses show enhanced hybridization between Au and LMO for delithiated surfaces leading to partial oxidation of Au upon delithiation. This study suggests that, in addition to transition metal dissolution from electrode surfaces, protective coating design must also balance potential energy effects induced by charge transfer at the electrode‐coating interface.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/nano10091870
