skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Assessing the Physiological Relevance of Cough Simulators for Respiratory Droplet Dispersion
Various breathing and cough simulators have been used to model respiratory droplet dispersion and viral droplets, in particular for SARS-CoV-2 modeling. However, limited data are available comparing these cough simulations to physiological breathing and coughing. In this study, three different cough simulators (Teleflex Mucosal Atomization Device Nasal (MAD Nasal), a spray gun, and GloGermTM MIST) that have been used in the literature were studied to assess their physiologic relevance. Droplet size, velocity, dispersion, and force generated by the simulators were measured. Droplet size was measured with scanning electron microscopy (SEM). Slow-motion videography was used to 3D reconstruct and measure the velocity of each simulated cough. A force-sensitive resistor was used to measure the force of each simulated cough. The average size of droplets from each cough simulator was 176 to 220 µm. MAD Nasal, the spray gun, and GloGermTM MIST traveled 0.38 m, 0.89 m, and 1.62 m respectively. The average velocities for the MAD Nasal, spray gun, and GloGermTM MIST were 1.57 m/s, 2.60 m/s, and 9.27 m/s respectively, and all yielded a force of <0.5 Newtons. GloGermTM MIST and the spray gun most closely resemble physiological coughs and breathing respectively. In conclusion, none of the simulators tested accurately modeled all physiologic characteristics (droplet size, 3-D dispersion velocity, and force) of a cough, while there were various strengths and weaknesses of each method. One should take this into account when performing simulations with these devices.  more » « less
Award ID(s):
1845683
PAR ID:
10220437
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
Journal of Clinical Medicine
Volume:
9
Issue:
9
ISSN:
2077-0383
Page Range / eLocation ID:
3002
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Environmental Health Insights)
    The global pandemic of COVID-19 has highlighted the importance of understanding the role that exhaled droplets play in virus transmission in community settings. Computational Fluid Dynamics (CFD) enables systematic examination of roles the exhaled droplets play in the spread of SARS-CoV-2 in indoor environments. This analysis uses published exhaled droplet size distributions combined with terminal aerosol droplet size based on measured peak concentrations for SARS-CoV-2 RNA in aerosols to simulate exhaled droplet dispersion, evaporation, and deposition in a supermarket checkout area and rideshare car where close proximity with other individuals is common. Using air inlet velocity of 2 m/s in the passenger car and ASHRAE recommendations for ventilation and comfort in the supermarket, simulations demonstrate that exhaled droplets <20 μm that contain the majority of viral RNA evaporated leaving residual droplet nuclei that remain aerosolized in the air. Subsequently ~ 70% of these droplet nuclei deposited in the supermarket and the car with the reminder vented from the space. The maximum surface deposition of droplet nuclei/m2for speaking and coughing were 2 and 819, 18 and 1387 for supermarket and car respectively. Approximately 15% of the total exhaled droplets (aerodynamic diameters 20-700 µm) were deposited on surfaces in close proximity to the individual. Due to the non-linear distribution of viral RNA across droplet sizes, however, these larger exhaled droplets that deposit on surfaces have low viral content. Maximum surface deposition of viral RNA was 70 and 1.7 × 103virions/m2for speaking and 2.3 × 104and 9.3 × 104virions/m2for coughing in the supermarket and car respectively while the initial airborne concentration of viral RNA was 7 × 106copies per ml. Integrating the droplet size distributions with viral load distributions, this study helps explain the apparent importance of inhalation exposures compared to surface contact observed in the pandemic. 
    more » « less
  2. ; ; ; (, Frontiers in Mechanical Engineering)
    Introduction:Agriculture is the largest user of water globally (i.e., 70% of freshwater use) and within the United States (i.e., 42% of freshwater use); irrigation ensures crops receive adequate water, thereby increasing crop yields. Surfactants have been used in various agricultural spray products to increase spray stability and alter droplet sizes. Methods:The effects of the addition of surfactant (0.1 wt% Surfactin; surface tension of 29.2 mN/m) to distilled water (72.79 mN/m) on spray dynamics and droplet formation were investigated in four flat fan (206.8–413.7 kPa), one full cone (137.9–413.7 kPa), and three LEPA bubbler (41.4–103.4 kPa) nozzles via imaging. Results and discussion:The flat fan and cone nozzles experienced second wind-induced breakup (i.e., unstable wavelengths drive breakup) of the liquid sheets exiting the nozzle; the addition of surfactant resulted in an increased breakup length and a decreased droplet size. The fan nozzles volumetric median droplet diameter decreased with the addition of surfactant (e.g., decreased by 26.3–65.6 μm in one nozzle). The full cone nozzle volumetric median droplet diameter decreased initially with the addition of surfactant (27.8, 14.3, and 13.4 μm at 137.9, 206.8, and 310.3 kPa respectively), but increased at 413.7 kPa (24.3 μm). Sprays from the bubbler nozzles were measured and observed to experience Rayleigh (i.e., the droplets form via capillary pinching at the end of the jet) and first wind-induced breakup (i.e., air impacts breakup along with capillary pinching). The effect of Surfactin on droplet size was minimal for the 41.4 kPa bubbler nozzle. The addition of surfactant increased the diameter of the jet or ligament formed from the bubbler plate, thereby increasing the breakup length and the droplet size at 68.9 and 103.4 kPa (droplet size increased by 750.6 and 4,462.7 μm, respectively). 
    more » « less
  3. ; ; (, GSA Annual Meeting in Indianapolis, Indiana, USA - 2018, Paper No. 262-3)
    Core formation in small planetary bodies likely involves percolation of immiscible liquids (e.g. S- and C- rich iron alloys) through pore spaces in a silicate medium. The manner in which this phenomenon occurs is not fully understood. Furthermore, it is unknown whether the metallic melts can physically segregate during percolation. To improve our understanding of core formation in small planetesimals, we performed analog experiments. We used an emulsion of oil and water to simulate an emulsion of S-rich and C-rich iron alloys, respectively. The experiments were performed in a Hele-Shaw cell, a thin “channel” made of two acrylic plates (51 cm x 15 cmx 1.3 cm) kept apart with a thin aluminum plate (0.27 mm). A U-shaped cut out of the aluminum plate formed the channel. We used a syringe pump to inject the emulsion into the channel through a hole in the top plate. We investigated the effect of injection rate and droplet size on the percolation behavior of the emulsion. We observed that droplet velocity was size dependent. The smallest droplet size detected was 0.0133 mm2 with a velocity of 0.67 mm/s. Medium size droplets ranged from 0.03mm2 – ~10 mm2 with average velocity of ~0.43 mm/s. Larger droplets moved faster: the largest droplet, with an area of 91.4 mm2, had a velocity of 7.95 mm/s. We suggest that (1) suspended droplets slow down when they begin to touch the Hele-Shaw plates (medium size droplets), and (2) droplets flow faster when they become large enough to deform with the flow. We also tested percolation through a channel filled with polydisperse acrylic particles of diameter < 50 µm. When injected into the granular matrix, the oil formed a wetting front while the water advanced in “pulses”. These pulses may represent the faster flow of larger water droplets. In conclusion, the size of the droplets affects their velocity and possibly their ability to migrate through pore networks. The results suggest that immiscible liquids could potentially segregate due to different percolation efficiencies of the non-wetting/wetting phases. Consequently, this would affect the distribution of the metallic components within differentiated planetesimals. 
    more » « less
  4. ; ; ; (, Proceedings of the ASME 2024 Fluids Engineering Division Summer Meeting)
    Liquid droplet impact is a subject that has been investigated in both engineering and non-engineering applications to understand and to control this phenomenon. Spray cooling, ink-jet printing, spray coating and painting, soil erosion prevention, pesticide application, and impact erosion are merely a few examples in which droplet impact is involved. Erosion caused by droplet impact on a solid surface is important in numerous elements of industrial equipment, such as pipelines, steam turbines, and wind turbine blades. Though experimental and modeling studies have been performed on this topic, most failed to perform quantitative investigation especially when it came to the erosion of wind turbine blades. Moreover, most approaches assume that the impacting droplets are completely spherical and unaffected by any local turbulence or vortex shedding. As the droplet erosion process could be affected by several parameters, such as the impact velocity, shape and size of the droplets, this study focuses on investigating droplet properties and movement in a controlled lab environment. High speed imaging and Particle Image Velocimetry (PIV) methods are used for this purpose. PIV is used to measure the velocity, circularity, and size of the falling droplets in both disturbed and un-disturbed flow conditions. High-speed camera imaging provides additional insight to the path of the droplets’ movement in the presence of any turbulence. Experiments are performed at a variety of flow rates utilizing a range of blunt needle gauge sizes to create different droplet sizes. It is observed that the blunt needles produce a train of droplets that are different in size following each leading droplet. This is a crucial observation as it will have a direct impact on the magnitude of erosion and should be considered in the future modeling efforts. 
    more » « less
  5. ; ; ; ; ; ; (, The American Society of Mechanical Engineers Fluids Engineering Division Summer Meeting)
    Abstract The significance of respiratory droplet transmission in spreading respiratory diseases such as COVID-19 has been identified by researchers. Although one cough or sneeze generates a large number of respiratory droplets, they are usually infrequent. In comparison, speaking and singing generate fewer droplets, but occur much more often, highlighting their potential as a vector for airborne transmission. However, the flow dynamics of speech and the transmission of speech droplets have not been fully investigated. To shed light on this topic, two-dimensional geometries of a vocal tract for a labiodental fricative [f] were generated based on real-time MRI of a subject during pronouncing [f]. In these models, two different curvatures were considered for the tip tongue shape and the lower lip to highlight the effects of the articulator geometries on transmission dynamics. The commercial ANSYS-Fluent CFD software was used to solve the complex expiratory speech airflow trajectories. Simultaneously, the discrete phase model of the software was used to track submicron and large size respiratory droplets exhaled during [f] utterance. The simulations were performed for high, normal, and low lung pressures to explore the influence of loud, normal, and soft utterances, respectively, on the airflow dynamics. The presented results demonstrate the variability of the airflow and droplet propagation as a function of the vocal tract geometrical characteristics and loudness. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email