skip to main content

Explore Research Products in the NSF-PAR

Title: Efficiency Optimization of Dual Active Bridge DC– DC Converter with Triple Phase-Shift Control
The primary purpose of this paper is to obtain accurate analytical expressions of the dual active bridge (DAB) converter under the three-degree of freedom control technique. This technique, known as triple phase-shift (TPS) modulation, is utilized for the efficiency optimization of different operating zones and modes of the DAB. Three operating zones and modes have been retained to analyze the converter. Depending on the operating regions and due to the high nonlinearity of the obtained expressions, two optimization techniques have been used. The offline particle swarm optimization (PSO) method is utilized in local optimization (LO) and results in a numerical value. The Lagrange Multiplier (LM) is utilized in global optimization (GO) and results in a closed form expression. In the case of LO, the optimal duty cycles that minimize the power loss are not the optimal values for the minimum root-mean-square (RMS) current or peak current stress. Conversely, in the case of GO, the optimal duty cycles minimize the RMS, peak current and power loss at the same time for the entire power range. Detailed analyses and simulation results from MATLAB/Simulink are given to prove the effectiveness of the proposed method.  more » « less
Award ID(s):
1939124
NSF-PAR ID:
10221386
Author(s) / Creator(s):
; ; ;
Date Published:
Journal Name:
2020 IEEE Energy Conversion Congress and Exposition (ECCE)
Page Range / eLocation ID:
1217 to 1222
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ( , 2020 IEEE Transportation Electrification Conference & Expo (ITEC))
    null (Ed.)
    High frequency modular power converters are increasingly becoming popular due to their small size and weight. Targeting the input-series and output-parallel (ISOP) dual active bridge (DAB) DC-DC converters, this paper proposes a control scheme based on optimal triple phase-shift (TPS) control for both power sharing control and RMS current minimization. This achieves balanced power transmission, even under mismatched leakage inductance of a DAB module of the ISOP. In order to obtain the optimal zones of operation for the converter, the RMS current was minimized using the Lagrange multiplier method to obtain the optimal duty cycles. The power balancing was added to compensate unbalanced power sharing for variations in model parameters or module shutdown. Analyses and simulation results through MATLAB/Simulink are presented to validate the proposed controller. 
    more » « less
  2. ; ; ; ( , 2021 IEEE 12th Annual International Symposium on Power Electronics for Distributed Generation Systems)
    In this study, a power converter topology and control schemes for the power converter stages are proposed for a DC extreme fast charger. The proposed system is composed of a cascaded H-bridge (CHB) converter as the active front end (AFE), and an input series output parallel (ISOP), which includes three parallel connected dual active bridge (DAB) cells. A modified Lyapunov Function (LF) based control strategy is applied to obtain high current control response for the AFE. An additional controller to remove the voltage unbalances among the H-bridges is also presented. Additionally, the triple phase-shift (TPS) control method is applied for the ISOP DAB converter. A Lagrange Multiplier (LM) based optimization study is performed to minimize the RMS current of the transformer. The performance of the proposed converter topology and control strategies is validated with MATLAB/Simulink simulations. 
    more » « less
  3. ; ; ; ; ( , IEEE Open Journal of Power Electronics)
    This paper demonstrates a high-efficiency modular multilevel resonant DC-DC converter (MMRC) with zero-voltage switching (ZVS) capability. In order to minimize the conduction loss in the converter, optimizing the root-mean-square (RMS) current flowing through switching devices is considered an effective approach. The analysis of circuit configuration and operating principle show that the RMS value of the current flowing through switching devices is closely related to the factors such as the resonant tank parameters, switching frequency, converter output voltage and current, etc. A quantitative analysis that considers all these factors has been performed to evaluate the RMS current of all the components in the circuit. When the circuit parameters are carefully designed, the switch current waveform can be close to the square waveform, which has a low RMS value and results in low conduction loss. And a design example based on the theoretical analysis is presented to show the design procedures of the presented converter. A 600 W 48 V-to-12 V prototype is built with the parameters obtained from the design example section. Simulation and experiments have been performed to verify the high-efficiency feature of the designed converter. The measured converter peak efficiency reaches 99.55% when it operates at 200 kHz. And its power density can be as high as 795 W/in 3 . 
    more » « less
  4. ; ; ; ; ( , 2017 IEEE Energy Conversion Congress and Exposition (ECCE))
    The focus of this study is on the design of a full-bridge unidirectional resonant LLC Solid State Transformer. The proposed topology uses a high-frequency transformer to optimize the size and weight of the converter. This converter has the capability of operating at fluctuating load conditions while it keeps the voltage regulated in different operation point. The converter is designed to maintain soft switching by using a resonant circuit in this design to minimize the switching loss of the high frequency converter. ZVS in the leading leg for turn on mode and ZCS commutation in the lagging leg for all of the modes are achieved in the H-bridge through the suggested circuitry which is analyzed mathematically in detail in this study. A combination of Pulse frequency modulation (PFM) and Phase Shifting Modulation (PSM) are utilized to control this resonant converter. The experimental setup for the suggested configuration was implemented and the results of the simulation and calculations have been verified with test results. The hardware set up was tested with two different power levels and the output results confirm that the control method works properly to feed the load and keeps the converter working in the expected frequency range and maintaining the soft switching to decrease switching loss. The results shows conversion efficiency of 97.18% is achieved. 
    more » « less
  5. ; ; ; ; ; ( , IEEE transactions on circuits and systems)
    With the increasing complexity of highly integrated system on chips (SoCs), the power management system (PMS) is required to provide several power supplies efficiently for individual blocks. This paper presents a single-inductor multiple outputs (SIMO) an inductor-first hybrid converter that generates three outputs between 0.4V and 1.6V from a 1.8V input. The proposed multiple-output hybrid power stage can improve the conversion efficiency by reducing inductor current while extending the output voltage range compared with the existing hybrid topologies. In addition, the proposed converter employs an on-chip switched-capacitor power stage (SCPS) with a dual switching frequency technique, resulting in a fast response time, low cross-regulation, and reduced number of on-chip pads. Measurement results show that the converter achieves a peak efficiency of 87.5% with a maximum output current of 450mA. The converter is integrated with a fast voltage regulation loop with a 500MHz system clock to achieve less than 0.01mA/mV cross-regulation and a maximum 20mV overshoot at full-load transient response. The design is fabricated in the standard 180nm CMOS technology 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email