An official website of the United States government
Photocatalysis, mainly using TiO2 as a catalyst, has emerged as a promising method to address the issue of wastewater treatment. This study explores the enhanced photocatalytic activity of TiO2 through the introduction of reduced graphene oxide (rGO) and cadmium sulfide (CdS) as selective metal dopants. The incorporation of rGO and CdS into the TiO2 lattice aims to optimize its photocatalytic properties, including bandgap engineering, charge carrier separation, and surface reactivity. The unique combination of CdS and rGO with TiO2 is expected to boost degradation efficiency and reduce the reliance on expensive and potentially harmful sensitizers. This experimental investigation involves the synthesis and characterization of TiO2-based photocatalysts. The photocatalytic degradation of methyl orange (MO) and methylene blue (MB) was assessed under controlled laboratory conditions, studying the influence of metal dopants on degradation kinetics and degradation efficiency. Furthermore, the synthesized photocatalyst is characterized by advanced techniques, including BET, SEM, TEM, XRD, and XPS analyses. The degraded samples were analyzed by UV-Vis spectroscopy. Insights into the photoexcitation and charge transfer processes shed light on the role of metal dopants in enhancing photocatalytic performance. The results demonstrate the potential of a TiO2-rGO-CdS-based photocatalyst in which 100% degradation was achieved within four hours for MO and six hours for MB, confirming efficient azo dye degradation. The findings contribute to understanding the fundamental principles underlying the photocatalytic process and provide valuable guidance for designing and optimizing advanced photocatalytic systems. Ultimately, this research contributes to the development of sustainable and effective technologies for removing azo dyes from various wastewaters, promoting environmental preservation and human well-being.
more »
« less
Facile Synthesis of “Boron-Doped” Carbon Dots and Their Application in Visible-Light-Driven Photocatalytic Degradation of Organic Dyes
Carbon dots (C-dots) were facilely fabricated via a hydrothermal method and fully characterized. Our study shows that the as-synthesized C-dots are nontoxic, negatively charged spherical particles (average diameter 4.7 nm) with excellent water dispersion ability. Furthermore, the C-dots have a rich presence of surface functionalities such as hydroxyls and carboxyls as well as amines. The significance of the C-dots as highly efficient photocatalysts for rhodamine B (RhB) and methylene blue (MB) degradation was explored. The C-dots demonstrate excellent photocatalytic activity, achieving 100% of RhB and MB degradation within 170 min. The degradation rate constants for RhB and MB were 1.8 × 10−2 and 2.4 × 10−2 min−1, respectively. The photocatalytic degradation performances of the C-dots are comparable to those metal-based photocatalysts and generally better than previously reported C-dots photocatalysts. Collectively considering the excellent photocatalytic activity toward organic dye degradation, as well as the fact that they are facilely synthesized with no need of further doping, compositing, and tedious purification and separation, the C-dots fabricated in this work are demonstrated to be a promising alternative for pollutant degradation and environment protection.
more »
« less
- Award ID(s):
- 2041413
- PAR ID:
- 10223032
- Date Published:
- Journal Name:
- Nanomaterials
- Volume:
- 10
- Issue:
- 8
- ISSN:
- 2079-4991
- Page Range / eLocation ID:
- 1560
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Photocatalytic self-cleaning coatings with a high surface area are important for a wide range of applications, including optical coatings, solar panels, mirrors, etc. Here, we designed a highly porous TiO2 coating with photoinduced self-cleaning characteristics and very high hydrophilicity. This was achieved using the swelling-assisted sequential infiltration synthesis (SIS) of a block copolymer (BCP) template, which was followed by polymer removal via oxidative thermal annealing. The quartz crystal microbalance (QCM) was employed to optimize the infiltration process by estimating the mass of material infiltrated into the polymer template as a function of the number of SIS cycles. This adopted swelling-assisted SIS approach resulted in a smooth uniform TiO2 film with an interconnected network of pores. The synthesized film exhibited good crystallinity in the anatase phase. The resulting nanoporous TiO2 coatings were tested for their functional characteristics. Exposure to UV irradiation for 1 h induced an improvement in the hydrophilicity of coatings with wetting angle reducing to unmeasurable values upon contact with water droplets. Furthermore, their self-cleaning characteristics were tested by measuring the photocatalytic degradation of methylene blue (MB). The synthesized porous TiO2 nanostructures displayed promising photocatalytic activity, demonstrating the degradation of approximately 92% of MB after 180 min under ultraviolet (UV) light irradiation. Thus, the level of performance was comparable to the photoactivity of commercial anatase TiO2 nanoparticles of the same quantity. Our results highlight a new robust approach for designing hydrophilic self-cleaning coatings with controlled porosity and composition.more » « less
-
The interfacial contact between TiO 2 and graphitic carbon in a hybrid composite plays a critical role in electron transfer behavior, and in turn, its photocatalytic efficiency. Herein, we report a new approach for improving the interfacial contact and delaying charge carrier recombination in the hybrid by wrapping short single-wall carbon nanotubes (SWCNTs) on TiO 2 particles (100 nm) via a hydration-condensation technique. Short SWCNTs with an average length of 125 ± 90 nm were obtained from an ultrasonication-assisted cutting process of pristine SWCNTs (1–3 μm in length). In comparison to conventional TiO 2 –SWCNT composites synthesized from long SWCNTs (1.2 ± 0.7 μm), TiO 2 wrapped with short SWCNTs showed longer lifetimes of photogenerated electrons and holes, as well as a superior photocatalytic activity in the gas-phase degradation of acetaldehyde. In addition, upon comparison with a TiO 2 –nanographene “quasi-core–shell” structure, TiO 2 -short SWCNT structures offer better electron-capturing efficiency and slightly higher photocatalytic performance, revealing the impact of the dimensions of graphitic structures on the interfacial transfer of electrons and light penetration to TiO 2 . The engineering of the TiO 2 –SWCNT structure is expected to benefit photocatalytic degradation of other volatile organic compounds, and provide alternative pathways to further improve the efficiency of other carbon-based photocatalysts.more » « less
-
The present work reports the synthesis of cobalt ferrite and its nanohybrids with polythiophene (PTh) in the weight ratios of 10% and 20%. The ferrite and its nanohybrids were characterized using thermogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy coupled with elemental mapping (Fe-SEM) to confirm the morphology as well as the structure of the synthesized nanohybrids. The nanohybrids were tested for their photocatalytic activity upon modification of PTh against Alizarin Yellow (AY), Congo Red (CR) and Brilliant Blue (BB). Almost 100% degradation was achieved in 30 min using 50 mg of the photocatalyst. The effect of catalyst concentration and dye concentration was also investigated to explore optimum concentration of the photocatalyst required for rapid degradation of the dye. The generation of radicals responsible for degradation was analyzed by radical scavenging experiments and a probable mechanism of degradation was proposed.more » « less
-
“Concentrate-and-degrade” is an effective strategy to promote mass transfer and degradation of pollutants in photocatalytic systems, yet suitable and cost-effective photocatalysts are required to practice the new concept. In this study, we doped a post-transition metal of Indium (In) on a novel composite adsorptive photocatalyst, activated carbon-supported titanate nanotubes (TNTs@AC), to effectively degrade perfluorooctanoic acid (PFOA). In/TNTs@AC exhibited both excellent PFOA adsorption (>99% in 30 min) and photodegradation (>99% in 4 h) under optimal conditions (25 °C, pH 7, 1 atm, 1 g/L catalyst, 0.1 mg/L PFOA, 254 nm). The heterojunction structure of the composite facilitated a cooperative adsorption mode of PFOA, i.e., binding of the carboxylic head group of PFOA to the metal oxide and attachment of the hydrophobic tail to AC. The resulting side-on adsorption mode facilitates the electron (e‒) transfer from the carboxylic head to the photogenerated hole (h+), which was the major oxidant verified by scavenger tests. Furthermore, the presence of In enables direct electron transfer and facilitates the subsequent stepwise defluorination. Finally, In/TNTs@AC was amenable to repeated uses in four consecutive adsorption-photodegradation runs. The findings showed that adsorptive photocatalysts can be prepared by hybridization of carbon and photoactive semiconductors and the enabled “concentrate-and-degrade” strategy is promising for the removal and degradation of trace levels of PFOA from polluted waters.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/nano10081560
