skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


  • NSF Public Access
  • Search Results
  • Surface Functionalization Utilizing Mesoporous Silica Nanoparticles for Enhanced Evanescent-Field Mid-Infrared Waveguide Gas Sensing
Title: Surface Functionalization Utilizing Mesoporous Silica Nanoparticles for Enhanced Evanescent-Field Mid-Infrared Waveguide Gas Sensing
This work focuses on the development of nanoparticle-based layer-by-layer (LbL) coatings for enhancing the detection sensitivity and selectivity of volatile organic compounds (VOCs) using on-chip mid-infrared (MIR) waveguides (WGs). First, we demonstrate construction of conformal coatings of polymer/mesoporous silica nanoparticles (MSNs) on the surface of Si-based WGs using the LbL technique and evaluate the coating deposition conditions, such as pH and substrate withdrawal speed, on the thickness and homogeneity of the assemblies. We then use the modified WGs to achieve enhanced sensitivity and selectivity of polar organic compounds, such as ethanol, versus non-polar ones, such as methane, in the MIR region. In addition, using density functional theory calculations, we show that such an improvement in sensing performance is achieved due to preferential adsorption of ethanol molecules within MSNs in the vicinity of the WG evanescent field.  more » « less
Award ID(s):
1835690
PAR ID:
10296236
Author(s) / Creator(s):
; ; ; ; ; ; ; ;
Date Published:
Journal Name:
Coatings
Volume:
11
Issue:
2
ISSN:
2079-6412
Page Range / eLocation ID:
118
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; ; ; ; et al (, Chemical Communications)
    null (Ed.)
    Functionalization of optical waveguides with submicron coatings of zinc peroxide (ZnO 2 ) and silica (SiO 2 ) nanoparticles (NPs) is reported that enabled selective concentration of acetone vapors in the vicinity of the waveguide, boosting the sensitivity of a mid infrared (MIR) on-chip detector. Controlled thickness was achieved by introducing precise control of the substrate withdrawal speed to the layer-by-layer (LbL) deposition technique. 
    more » « less
  2. ; ; (, Journal of Materials Research)
    Traditional dip-assisted layer-by-layer (LbL) assembly produces robust and conformal coatings, but it is time-consuming. Alternatively, spray-assisted layer-by-layer (SA-LbL) assembly has gained interest due to rapid processing resulting from the short adsorption time. However, it is challenging to assemble anisotropic nanomaterials using this spray-based approach. This is because the standard approach for fabricating “ all-polyelectrolyte ” LbL films does not necessarily give rise to satisfactory film growth when one of the adsorbing components is anisotropic. Here, polymers are combined with a model anisotropic nanomaterial via SA-LbL assembly. Specifically, graphene oxide (GO) is investigated, and the effect of anchor layer, colloidal stability, charge distribution along the carbon framework, and concentration of polymer on the growth and the film quality is examined to gain insight into how to achieve pinhole-free, smooth polymer/GO SA-LbL coatings. This approach might be applicable to other anisotropic nanomaterials such as clays or 2D nanomaterials for future development of uniform coatings by spraying. 
    more » « less
  3. ; ; (, Journal of Applied Polymer Science)
    Abstract Polyamide thin‐film composite (PA‐TFC) membranes make large‐scale desalination effective. Interfacial polymerization (IP) is used to make PA‐TFC membranes, but it may limit the range of monomers that can be used, which hinders progress toward advanced membranes. Layer‐by‐layer (LbL) sequential deposition could circumvent kinetic and thermodynamic limitations of the conventional IP process to facilitate incorporation of different co‐monomers into the membrane. The selective layer needs to be deposited onto a microporous support, but depositing LbL coatings on microporous supports often results in defective membranes. Using a poly(vinyl alcohol) (PVA) primer between the support and the LbL polyamide layer may prevent defect formation. The water permeance and salt rejection of a three layer, PVA‐primed, LbL‐based PA‐TFC membrane are discussed and compared to a membrane made without the PVA primer and a commercially available membrane. Mass transfer resistances are analyzed using a series resistance model and appear to be small or even negligible compared to that of the polyamide layer. Incorporation of a sulfonated co‐monomer into the polyamide via LbL is reported. The combination of a PVA primer layer and LbL sequential deposition may expand the range of co‐monomers that could be used relative to polyamide membranes prepared by the conventional IP process. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; (, Abstracts of papers - American Chemical Society)
    Direct layer-by-layer (LbL) assembly of cationic, small-molecule antibacterial bioactives with water-soluble, ionic polyphosphazenes (PPzs) containing trifluoroethoxy and carboxy substitients is reported. First, influence of PPzs hydrophobicity and antibiotic charge density on LbL assembly was studied via evolution of dry film thickness. We found that the use of fluorinated PPz polyelectrolytes enhanced ionic pairing within LbL coatings, and that increasing charge density of small molecules increased antibiotic uptake. This strategy was successful even in the case of gentamicin, a hydrophilic, small antibiotic with only 3 to 4 positive charges at pH 7.5. Confirmation of antibiotic presence in films was demonstrated via x-ray photoelectron spectroscopy. Importantly, LbL films of fluorinated PPz polyelectrolytes retained antibiotics in physiological conditions due to the enhanced hydrophobic interactions. In contrast, LbL films of non-fluorinated PPzs released antibiotics at low pH and in the presence of salt following the charge renormalization argument. The potential of these coatings with a biomedically relevant bacterial strain, Staphylococcus aureus, is discussed. 
    more » « less
  5. ; ; (, Advanced Materials Interfaces)
    Abstract Mechanisms of uptake in metal–organic materials are complex and are dependent on the chemistry of the pore space and material interface. In the current study, the importance of the material surface is evaluated on the water uptake of a metal–organic nanotube (UMONT) crystalline solid. This material has previously demonstrated selective water uptake and reported isotherms suggested a two‐step adsorption process that involved initial surface adsorption followed by pore filling. The proposed mechanism and importance of surface chemistry for water adsorption are tested by altering the surface of the UMONT with more hydrophobic surface coatings. Crystals of UMONT are coated with ammonium trifluoroacetate (ATFA), polyvinylidene fluoride (PVDF), and polyacrylonitrile (PAN), and the water adsorption behavior is analyzed through batch and flow‐through experiments. Uptake experiments reveal that ATFA significantly decreased the water uptake compared to observed in pristine UMONT while polymer coatings do not impact the adsorption behavior as significantly. In addition, ATFA disrupts the water selectivity of the UMONT material, allowing both ethanol and methanol to be detected in the system. These results indicate that changing the surface layer from a hydrophilic to hydrophobic with a chemisorbed monolayer will disturb the two‐step mechanism and the water uptake properties of the material. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email