The new material polypyrrole/MoS42−(MoS4‐Ppy), prepared by ion‐exchange of NO3‐ of NO3‐Ppy with MoS42−, displays high acid stability and excellent uptake for heavy metal ions such as Hg2+, Ag+, Cu2+, and Pb2+. The different maximum adsorption capacities (
The removal of heavy metal contaminants from water is important for public health, and recently many two-dimensional (2D) materials with high specific surface areas are being studied as promising new active components in water purification. In particular, 2D MoS2nanosheets have been used for the removal of various heavy metals, but usually in either in complex geometries and composites, or in the chemically exfoliated metallic 1T-MoS2phase. However, the interaction of heavy metals dissolved in water with unmodified semiconducting 2H-MoS2is not well studied. In this paper, we report a detailed fundamental investigation of how Pb2+ions interact with 2H-MoS2. We observe small solid clusters that form on the MoS2surfaces after exposing them to Pb(NO3)2aqueous solutions as shown by atomic force microscopy and transmission electron microscopy, and for liquid phase exfoliated MoS2we observe the nanosheets precipitating out of dispersion along with insoluble solid granules. We use a combination of x-ray photoelectron spectroscopy and x-ray diffraction to identify these solid clusters and granules as primarily PbSO4with some PbMoO4. We put forth an interaction mechanism that involves MoS2defects acting as initiation sites for the partial dissolution in aqueous oxygenated conditions which produces MoO42−and SO42−ions to form the solids with Pb2+. These results are an important contribution to our fundamental understanding of how MoS2interacts with metal ions and will influence further efforts to exploit MoS2for water remediation applications.
more » « less- Award ID(s):
- 1906030
- NSF-PAR ID:
- 10303208
- Publisher / Repository:
- IOP Publishing
- Date Published:
- Journal Name:
- Journal of Physics: Materials
- Volume:
- 3
- Issue:
- 2
- ISSN:
- 2515-7639
- Page Range / eLocation ID:
- Article No. 024007
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract q m) for Cu2+, Pb2+, Hg2+, and Ag+depend on the various binding modes arising from the different thiophilicity of these metal ions. The removals of Ag+and Pb2+reach >99.6% within 5 min, and for highly toxic Hg2+, >98% removal achieves at 1 min. At strong acid limit, the exceptionalq m(Ag+) of 725 mg g−1places the MoS4‐Ppy at the top of materials for such removal. Uptake kinetics of Ag+, Hg2+, and Pb2+is extremely fast: >99.9% removal rates at wide pH range (0.5–6) within 1–5 min. Also, at strongly acidic conditions (pH ≈ 1), for highly toxic Hg2+, <2 ppb concentration can be achieved, accepted as safe limit. The MoS4‐Ppy demonstrates an outstanding ability to separate low‐concentrated Ag+from high concentrated Cu2+especially under strong acidic conditions (pH ≈ 1), showing a large separation factor SFAg/Cu(K dAg/K dCu) of 105(>100). MoS4‐Ppy is a superior and novel sorbent material for water remediation applications as well as precious metals recovery. -
more » « less
Abstract Despite significant progress in solution‐processing of 2D materials, it remains challenging to reliably print high‐performance semiconducting channels that can be efficiently modulated in a field‐effect transistor (FET). Herein, electrochemically exfoliated MoS2nanosheets are inkjet‐printed into ultrathin semiconducting channels, resulting in high on/off current ratios up to 103. The reported printing strategy is reliable and general for thin film channel fabrication even in the presence of the ubiquitous coffee‐ring effect. Statistical modeling analysis on the printed pattern profiles suggests that a spaced parallel printing approach can overcome the coffee‐ring effect during inkjet printing, resulting in uniform 2D flake percolation networks. The uniformity of the printed features allows the MoS2channel to be hundreds of micrometers long, which easily accommodates the typical inkjet printing resolution of tens of micrometers, thereby enabling fully printed FETs. As a proof of concept, FET water sensors are demonstrated using printed MoS2as the FET channel, and printed graphene as the electrodes and the sensing area. After functionalization of the sensing area, the printed water sensor shows a selective response to Pb2+in water down to 2 ppb. This work paves the way for additive nanomanufacturing of FET‐based sensors and related devices using 2D nanomaterials.
-
null (Ed.)Heavy metal ions are highly toxic and widely spread as environmental pollutants. This work reports the development of two novel chelating adsorbents, based on the chemical modifications of graphene oxide and zirconium phosphate by functionalization with melamine-based chelating ligands for the effective and selective extraction of Hg( ii ) and Pb( ii ) from contaminated water sources. The first adsorbent melamine, thiourea-partially reduced graphene oxide (MT-PRGO) combines the heavier donor atom sulfur with the amine and triazine nitrogen's functional groups attached to the partially reduced GO nanosheets to effectively capture Hg( ii ) ions from water. The MT-PRGO adsorbent shows high efficiency for the extraction of Hg( ii ) with a capacity of 651 mg g −1 and very fast kinetics resulting in a 100% removal of Hg( ii ) from 500 ppb and 50 ppm concentrations in 15 second and 30 min, respectively. The second adsorbent, melamine zirconium phosphate (M-ZrP), is designed to combine the amine and triazine nitrogen's functional groups of melamine with the hydroxyl active sites of zirconium phosphate to effectively capture Pb( ii ) ions from water. The M-ZrP adsorbent shows exceptionally high adsorption affinity for Pb( ii ) with a capacity of 681 mg g −1 and 1000 mg g −1 using an adsorbent dose of 1 g L −1 and 2 g L −1 , respectively. The high adsorption capacity is also coupled with fast kinetics where the equilibrium time required for the 100% removal of Pb( ii ) from 1 ppm, 100 ppm and 1000 ppm concentrations is 40 seconds, 5 min and 30 min, respectively using an adsorbent dose of 1 g L −1 . In a mixture of six heavy metal ions at a concentration of 10 ppm, the removal efficiency is 100% for Pb( ii ), 99% for Hg( ii ), Cd( ii ) and Zn( ii ), 94% for Cu( ii ), and 90% for Ni( ii ) while at a higher concentration of 250 ppm the removal efficiency for Pb( ii ) is 95% compared to 23% for Hg( ii ) and less than 10% for the other ions. Because of the fast adsorption kinetics, high removal capacity, excellent regeneration, stability and reusability, the MT-PRGO and M-ZrP are proposed as top performing remediation adsorbents for the solid phase extraction of Hg( ii ) and Pb( ii ), respectively from contaminated water.more » « less
-
null (Ed.)A highly porous adsorbent based on a metal–organic framework was successfully designed and applied as an innovative adsorbent in the solid phase for the heavy metal removal. MIL-125 was densely decorated by 2-imino-4-thiobiuret functional groups, which generated a green, rapid, and efficacious adsorbent for the uptake of Hg( ii ) and Pb( ii ) from aqueous solutions. ITB-MIL-125 showed a high adsorption affinity toward mercury( ii ) ions of 946.0 mg g −1 due to covalent bond formation with accessible sulfur-based functionality. Different factors were studied, such as the initial concentration, pH, contact time, and competitive ions, under same circumstances at the room temperature. Moreover, the experimental adsorption data were in excellent agreement with the Langmuir adsorption isotherm and pseudo-second order kinetics. At a high concentration of 100 ppm mixture of six metals, ITB-MIL-125 exhibited a high adsorption capacity, reaching more than 82% of Hg( ii ) compared to 62%, 30%, 2%, 1.9%, and 1.6% for Pb( ii ), Cu( ii ), Cd( ii ), Ni( ii ), and Zn( ii ), respectively.more » « less
-
more » « less
Abstract A novel transition metal chalcohalide [Cr7S8(en)8Cl2]Cl3 ⋅ 2H2O, with [Cr7S8]5+dicubane cationic clusters, has been synthesized by a low temperature solvothermal method, using dimethyl sulfoxide (DMSO) and ethylenediamine (
en ) solvents. Ethylenediamine ligand exhibits bi‐ and monodentate coordination modes; in the latter case ethylenediamine coordinates to Cr atoms of adjacent clusters, giving rise to a 2D polymeric structure. Although magnetic susceptibility shows no magnetic ordering down to 1.8 K, a highly negative Weiss constant,θ =−224(2) K, obtained from Curie‐Weiss fit of inverse susceptibility, suggests strong antiferromagnetic (AFM) interactions betweenS =3/2 Cr(III) centers. Due to the complexity of the system with (2S +1)7=16384 microstates from seven Cr3+centers, a simplified model with only two exchange constants was used for simulations. Density‐functional theory (DFT) calculations yielded the two exchange constants to beJ 1=−21.4 cm−1andJ 2=−30.2 cm−1, confirming competing AFM coupling between the shared Cr3+center and the peripheral Cr3+ions of the dicubane cluster. The best simulation of the experimental data was obtained withJ 1=−20.0 cm−1andJ 2=−21.0 cm−1, in agreement with the slightly stronger AFM exchange within the triangles of the peripheral Cr3+ions as compared to the AFM exchange between the central and peripheral Cr3+ions. This compound is proposed as a synthon towards magnetically frustrated systems assembled by linking dicubane transition metal‐chalcogenide clusters into polymeric networks.
