An official website of the United States government
The ammonia (NH3) and dimethyl ether (DME) mixture is a promising alternative fuel that offers the potential for cleaner combustion. This study presents an investigation of the autoignition-assisted flame speeds of stochiometric NH3/DME mixtures under conditions relevant to practical combustion systems. Experiments were conducted at pressures of 5 and 10 bar, gas temperatures ranging from 625 to 708 K, and three DME concentrations (10, 20, and 30%, mole fraction basis) in NH3/DME fuel mixtures using a rapid compression machine-flame (RCM-Flame) apparatus. For the majority of the autoignition experiments, first-stage ignition delay time was observed. Thus, the flame experiments were performed by igniting the spark both before and after the first-stage ignition delay time. The results are presented in terms of the Beta-Damköhler Number, defined as the ratio of spark ignition time to the first-stage ignition delay. The flame speed changes depending on the Beta-Damköhler Number, pressure, gas temperature, and DME concentration. The flame speed increases by increasing the temperature, decreasing the pressure, and increasing DME concentrations. However, the effect of Beta-Damköhler Number on flame speed is complicated: with 10% DME in the mixture, the flame speed is independent to Beta-Damköhler Number, and slight observed slight decrease of flame speed is due to the temperature drop during the post-compression period; with 20% DME in the mixture, at both pressures, the flame speed jumps after the first ignition delay (or Beta-Damköhler Number of one) , and remains constant before and after; similar behavior was observed with 30% DME in the mixture at 5 bar, however, at some temperatures, the flame speed increases at Beta-Damköhler Number of greater than one, and at 10 bar, the first ignition delay was short and flame speed was not measured at Beta-Damköhler Number of less than one. For all studied conditions, a linear trend was observed between burning velocity and stretch rate. Positive Markstein lengths were observed at most conditions, except for two specific gas temperatures (664 K at 5 bar and 671 K at 10 bar) with 30% DME, where negative Markstein lengths are found. One-dimensional laminar flame speed simulations agreed with measured data for Beta-Damköhler Numbers. less than one, but underpredicted the measured data at other conditions.
more »
« less
Computational Analysis of Premixed Syngas/Air Combustion in Micro-channels: Impacts of Flow Rate and Fuel Composition
Due to increasing demand for clean and green energy, a need exists for fuels with low emissions, such as synthetic gas (syngas), which exhibits excellent combustion properties and has demonstrated promise in low-emission energy production, especially at microscales. However, due to complicated flame properties in microscale systems, it is of utmost importance to describe syngas combustion and comprehend its properties with respect to its boundary and inlet conditions, and its geometric characteristics. The present work studied premixed syngas combustion in a two-dimensional channel, with a length of 20 mm and a half-width of 1 mm, using computational approaches. Specifically, a fixed temperature gradient was imposed at the upper wall, from 300 K at the inlet to 1500 K at the outlet, to preheat the mixture, accounting for the conjugate heat transfer through the walls. The detailed chemistry of the ignition process was imitated using the San Diego mechanism involving 46 species and 235 reactions. For the given boundary conditions, stoichiometric premixed syngas containing various compositions of carbon monoxide, methane, and hydrogen, over a range of inlet velocities, was simulated, and various combustion phenomena, such as ignition, flame stabilization, and flames with repeated extinction and ignition (FREI), were analyzed using different metrics. The flame stability and the ignition time were found to correlate with the inlet velocity for a given syngas mixture composition. Similarly, for a given inlet velocity, the correlation of the flame properties with respect to the syngas composition was further scrutinized.
more »
« less
- Award ID(s):
- 1726534
- PAR ID:
- 10314875
- Date Published:
- Journal Name:
- Energies
- Volume:
- 14
- Issue:
- 14
- ISSN:
- 1996-1073
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Laminar flame speeds at high pressure are difficult to experimentally observe. Typically, high-pressure flame diagnostic is accomplished through observation of a spherically expanding flame in a constant volume chamber. However, flame instabilities at large radius and ignition effects at small radius limit measurable pressure range for Laminar flame speeds. Advanced combustion devices which operate at high pressures to improve capabilities and efficiencies require high quality laminar flame speed to aid in simulations and development. To expand the measurable range of flame data for high pressure flame measurement, this study proposes the further investigation of the ignition source and the incorporation of ignition diagnostics into the traditional flame speed analysis. To achieve this goal in future research, experimental spark propagation is observed and described in detail with the goal of improved experimental control and understanding. Parameters such as pressure, composition, electrode geometry and surface quality are discussed and the implication it has on the observed schlieren kernel propagation. Careful preparation of the ignition source can lead to improved surface and shape for future flame measurements. It is also shown that the thermal energy dissipated into the gas during discharge can be captured experimentally through measurement of the spark voltage, current and plasma sheath voltage drop. With the experimentally captured thermal energy, a simple energy balance can be used to describe the size of the observed ignition kernel for radius larger than 0.3 mm (following breakdown). The measurement of the thermal energy is described utilizing two experimental methods to find the discharge voltage of the nonequilibrium region at the boundary of the electrodes.more » « less
-
Many positive laboratory results that have been reported in which non-thermal plasmas, particularly repetitive nano second pulses, showed a reduction of ignition time delay and extension of flammability limits. However, there is a need for predictive models for designing practical systems. We present the results of a self-consistent model and simulation results of plasma assisted combustion of hydrogen air fuel mixture. The electrical discharge phase is modeled as a streamer discharge which is followed by the combustion kinetics phase. Nonequilibrium population of excited states leads to an increase in the reactivity and facilitates ignition and flame propagation. We have quantified some macroscopic properties of streamers such as radical production efficiency which will lead to the development of predictive tools. The concentration of radicals depends on the electrical energy density which is critical in determining ignition. We find that short duration streamers do not deposit enough energy to ignite hydrogen air mixtures. Also, the spatial and temporal electric energy density will influence the ignition delay and flame propagation velocity etc.more » « less
-
Measurements of a propagating flame are crucial to the understanding and verification of important flame phenomena. Specifically, laminar, unstretched flame speed is employed to describe complex flame behavior such as turbulence or stability. This data is necessary because advanced and more efficient combustion devices operate at these high pressures where this data is less reliable from the onset of flame instabilities. This research aims to develop a new flame speed measurement technique as an improvement over the traditional method. The analysis utilizes a constant pressure technique where the velocity of a spherical flame is visually measured. Flame propagation of stoichiometric flame from 1-6 atm are examined at radius up to 20mm at 300K. The novel analysis method incorporates flame data which is ignition affected to improve the traditional constant pressure methods. This allows for with the inclusion of ultra-small, highly stretched flame radii (0-10 mm). Electrical measurements of the ignition are utilized with a thermodynamic model to predict the velocity and temperature which result from plasma formation. This predicted temperature is used describe the influence ignition has on the flame velocity and is compared to the traditional adiabatic flame propagation over the radius observed. The extrapolated laminar burning speed measurement is found for both traditional and novel methods where the novel method has the benefit of additional, previously unused, flame propagation at the high stretch regime. Additionally, practical information about the plasma morphology, crucial to the experimental application of this method is also discussed.more » « less
-
Abstract Combustion instability, which is the result of a coupling between combustor acoustic modes and unsteady flame heat release rate, is a severely limiting factor in the operability and performance of modern gas turbine engines. This coupling can occur through different pathways, such as flow-field fluctuations or equivalence ratio fluctuations. In realistic combustor systems, there are complex hydrodynamic and thermo-chemical processes involved, which can lead to multiple coupling pathways. In order to understand and predict the mechanisms that govern the onset of combustion instability in real gas turbine engines, we consider the influences that each of these coupling pathways can have on the stability and dynamics of a partially premixed, swirl-stabilized flame. In this study, we use a model gas turbine combustor with two concentric swirling nozzles of air, separated by a ring of fuel injectors, operating at an elevated pressure of 5 bar. The flow split between the two streams is systematically varied to observe the impact on the flow and flame dynamics. High-speed stereoscopic particle image velocimetry, OH planar laser-induced fluorescence, and acetone planar laser-induced fluorescence are used to obtain information about the velocity field, flame, and fuel-flow behavior, respectively. Depending on the flow conditions, a thermoacoustic oscillation mode or a hydrodynamic mode, identified as the precessing vortex core, is present. The focus of this study is to characterize the mixture coupling processes in this partially premixed flame as well as the impact that the velocity oscillations have on mixture coupling. Our results show that, for this combustor system, changing the flow split between the two concentric nozzles can alter the dominant harmonic oscillation modes in the system, which can significantly impact the dispersion of fuel into air, thereby modulating the local equivalence ratio of the flame. This insight can be used to design instability control mechanisms in real gas turbine engines.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/en14144190
