skip to main content

Title: Enabling Conducting Polymer Applications: Methods for Achieving High Molecular Weight in Chemical Oxidative Polymerization in Alkyl- and Ether-Substituted Thiophenes
Polythiophenes (PTs) constitute a diverse array of promising materials for conducting polymer applications. However, many of the synthetic methods to produce PTs have been optimized only for the prototypical alkyl-substituted example poly(3-hexylthiophene) (P3HT). Improvement of these methods beyond P3HT is key to enabling the widespread application of PTs. In this work, P3HT and two ether-substituted PTs poly(2-dodecyl-2H,3H-thieno[3,4-b][1,4]dioxine) (PEDOT-C12) and poly(3,4-bis(hexyloxy)thiophene) (PBHOT) are synthesized by the FeCl3-initiated oxidative method under different conditions. Polymerization was carried out according to a common literature procedure (“reverse addition”) and a modified method (“standard addition”), which differ by the solvent system and the order of addition of reagents to the reaction mixture. Gel-permeation chromatography (GPC) was performed to determine the impact of the different methods on the molecular weights (Mw) and degree of polymerization (Xw) of the polymers relative to polystyrene standards. The standard addition method produced ether-substituted PTs with higher Mw and Xw than those produced using the reverse addition method for sterically unhindered monomers. For P3HT, the highest Mw and Xw were obtained using the reverse addition method. The results show the oxidation potential of the monomer and solution has the greatest impact on the yield and Xw obtained and should be carefully considered more » when optimizing the reaction conditions for different monomers. « less
Authors:
; ; ; ; ; ;
Award ID(s):
2122041
Publication Date:
NSF-PAR ID:
10325998
Journal Name:
Materials
Volume:
14
Issue:
20
Page Range or eLocation-ID:
6146
ISSN:
1996-1944
Sponsoring Org:
National Science Foundation
More Like this
  1. The tacticity of vinyl polymers has a profound effect on their physical properties. Despite the well-developed stereoselective methods for the polymerization of propylene and other nonpolar α-olefins, stereoselective polymerization of polar vinyl monomers has proven more challenging. We have designed chiral counterions that systematically bias the reactivity and chain-end stereochemical environment during cationic polymerization. This approach overrides conventional chain-end stereochemical bias to achieve catalyst-controlled stereoselective polymerization. We demonstrate that this method is general to vinyl ether substrates, providing access to a range of isotactic poly(vinyl ether)s with high degrees of isotacticity. The obtained materials display the tensile properties of commercial polyolefins but adhere more strongly to polar substrates by an order of magnitude, indicating their promise for next-generation engineering applications.
  2. Plastic production continually increases its share of global oil consumption. Thermoplastic elastomers (TPEs) are a necessary component of many industries, from automotive and construction to healthcare and medical devices. To reduce the environmental burden of TPE production on the world, we developed two new ABA triblock copolymers synthesized through cationic reversable addition–fragmentation chain transfer (RAFT) polymerization from renewable monomers. Using poly(isobutyl vinyl ether) (PIBVE) as the soft block and either poly( p -methoxystyrene) (PMOS) or poly(2,3-dihydrofuran) (PDHF) as the hard blocks, we produced triblock copolymers with varying volume fractions and characterized their material properties. PDHF-PIBVE-PDHF is sourced almost entirely from simple alcohols and exhibits mechanical properties comparable to those of commercial TPEs. This effort demonstrates the utility of cationic RAFT for the production of sustainable TPEs.
  3. Recent work has identified surface energy as a key figure of merit in predicting the morphology of bulk heterojunction organic solar cells and organic alloy formation in ternary blend organic solar cells. An efficient way of tuning surface energy in conjugated polymers is by introducing functionalised side chains. Here, we present a systematic study on a family of poly(3-hexylthiophene) (P3HT)-based random copolymers bearing five different functionalised side chains (ester, ether, diether, carbamate, nitrile) prepared by direct arylation polymerization (DArP) in terms of their effectiveness in tuning surface energy. This study also exemplifies the superior functional group tolerance in DArP compared to more traditional polymerization procedures. Water droplet contact angle measurements revealed that especially carbamates are highly effective in tuning surface energy, increasing the surface energy from 21.2 mN m −1 with P3HT to 25.5 mN m −1 and 28.6 mN m −1 in 25% and 50% carbamate functionalized copolymers, respectively. Importantly, by introducing a two-carbon-spacer between the conjugated backbone and the functional group, optical and electronic properties of P3HT could be largely maintained in the copolymers as determined by UV/Vis, cyclic voltammetry and space charge limited current hole mobility.
  4. Identifying plastics capable of chemical recycling to monomer (CRM) is the foremost challenge in creating a sustainable circular plastic economy. Polyacetals are promising candidates for CRM but lack useful tensile strengths owing to the low molecular weights produced using current uncontrolled cationic ring-opening polymerization (CROP) methods. Here, we present reversible-deactivation CROP of cyclic acetals using a commercial halomethyl ether initiator and an indium(III) bromide catalyst. Using this method, we synthesize poly(1,3-dioxolane) (PDXL), which demonstrates tensile strength comparable to some commodity polyolefins. Depolymerization of PDXL using strong acid catalysts returns monomer in near-quantitative yield and even proceeds from a commodity plastic waste mixture. Our efficient polymerization method affords a tough thermoplastic that can undergo selective depolymerization to monomer.
  5. The commercially available polyelectrolyte complex poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is ubiquitous in organic and hybrid electronics. As such, it has often been used as a benchmark material for fundamental studies and the development of new electronic devices. Yet, most studies on PEDOT:PSS have focused on its electronic conductivity in dry environments, with less consideration given to its ion transport, coupled ionic-electronic transport, and charge storage properties in aqueous environments. These properties are essential for applications in bioelectronics (sensors, actuators), charge storage devices, and electrochromic displays. Importantly, past studies on mixed ionic-electronic transport in PEDOT:PSS neglected to consider how the molecular structure of PSS affects mixed ionic-electronic transport. Herein, we therefore investigated the effect of the molecular weight and size distribution of PSS on the electronic properties and morphology of PEDOT:PSS both in dry and aqueous environments, and overall performance in organic electrochemical transistors (OECTs). Using reversible addition–fragmentation chain transfer (RAFT) polymerization with two different chain transfer agents, six PSS samples with monomodal, narrow ( Đ = 1.1) and broad ( Đ = 1.7) size distributions and varying molecular weights were synthesized and used as matrices for PEDOT. We found that using higher molecular weight of PSS ( M n = 145more »kg mol −1 ) and broad dispersity led to OECTs with the highest transconductance (up to 16 mS) and [ μC *] values (∼140 F cm −1 V −1 s −1 ) in PEDOT:PSS, despite having a lower volumetric capacitance ( C * = 35 ± 4 F cm −3 ). The differences were best explained by studying the microstructure of the films by atomic force microscopy (AFM). We found that heterogeneities in the PEDOT:PSS films (interconnected and large PEDOT- and PSS-rich domains) obtained from high molecular weight and high dispersity PSS led to higher charge mobility ( μ OECT ∼ 4 cm 2 V −1 s −1 ) and hence transconductance. These studies highlight the importance of considering molecular weight and size distribution in organic mixed ionic-electronic conductor, and could pave the way to designing high performance organic electronics for biological interfaces.« less