skip to main content


Title: Self-Aware MIMO Beamforming Systems : Dynamic Adaptation to Channel Conditions and Manufacturing Variability
Emerging wireless technologies employ MIMO beamforming antenna arrays to improve channel Signal-to-Noise Ratio (SNR). The increased dynamic range of channel SNR values that can be accommodated, creates power stress on Radio Frequency (RF) electronic circuitry. To alleviate this, we propose an approach in which the circuitry along with other transmission coding parameters can be dynamically tuned in response to channel SNR and beam-steering angle to either minimize power consumption or maximize throughput in the presence of manufacturing process variations while meeting a specified Bit Error Rate (BER) limit. The adaptation control policy is learned online and is facilitated by information obtained from testing of the RF circuitry before deployment.  more » « less
Award ID(s):
1815653
NSF-PAR ID:
10342735
Author(s) / Creator(s):
Date Published:
Journal Name:
Design Automation and Test in Europe
Page Range / eLocation ID:
572-575
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. null (Ed.)
    Adaptive communication for Internet of Things (IoT) and Wireless Body Area Network (WBAN) technologies is becoming increasingly popular due to the large power-performance trade-offs and highly dynamic channel conditions. Path loss, low signal to noise ratio (SNR) in the channel and network congestion adversely affect the data communication, each of which can be taken care of using different strategies such as reducing the data rate (for reducing congestion), increasing the output power (for increased path loss) and application of error correction coding (ECC, for low SNR). In this paper, we present a digital-friendly Transceiver SoC consisting of an RF-DAC based transmitter with orthogonally tunable output power, data rate and ECC that enables optimum system level bit error rate (BER) and energy for over 3-orders of energy-performance scalability, along with an ultra-low-power OOK receiver that receives the transmitter's control bits from a nearby base station for closed-loop control. The data rate and ECC control is achieved through a digital baseband, while a tapped capacitor matching network controls the output power. The energy efficiency of the transmitter is 27.6pJ/b at 10MSps and at 0.8V supply (~9X improvement over state-of-the-art), while the entire SoC (Transmitter+OOK receiver for controller feedback) consumes only 41.5pJ/b. 
    more » « less
  2. Full-duplex (FD) wireless and phased arrays are both promising techniques that can significantly improve data rates in future wireless networks. However, integrating FD with transmit (Tx) and receive (Rx) phased arrays is extremely challenging, due to the large number of self-interference (SI) channels. Previous work relies on either RF canceller hardware or on analog/digital Tx beamforming (TxBF) to achieve SI cancellation (SIC). However, Rx beamforming (RxBF) and the data rate gain introduced by FD nodes employing beamforming have not been considered yet. We study FD phased arrays with joint TxBF and RxBF with the objective of achieving improved FD data rates. The key idea is to carefully select the TxBF and RxBF weights to achieve wideband RF SIC in the spatial domain with minimal TxBF and RxBF gain losses. Essentially, TxBF and RxBF are repurposed, thereby not requiring specialized RF canceller circuitry. We formulate the corresponding optimization problem and develop an iterative algorithm to obtain an approximate solution with provable performance guarantees. Using SI channel measurements and datasets, we extensively evaluate the performance of the proposed approach in different use cases under various network settings. The results show that an FD phased array with 9/36/72 elements can cancel the total SI power to below the noise floor with sum TxBF and RxBF gain losses of 10.6/7.2/6.9 dB, even at Tx power level of 30 dBm. Moreover, the corresponding FD rate gains are at least 1.33/1.66/1.68×. 
    more » « less
  3. Full-duplex (FD) wireless and phased arrays are both promising techniques that can significantly improve data rates in future wireless networks. However, integrating FD with transmit (Tx) and receive (Rx) phased arrays is extremely challenging, due to the large number of self-interference (SI) channels. Previous work relies on either RF canceller hardware or on analog/digital Tx beamforming (TxBF) to achieve SI cancellation (SIC). However, Rx beamforming (RxBF) and the data rate gain introduced by FD nodes employing beamforming have not been considered yet. We study FD phased arrays with joint TxBF and RxBF with the objective of achieving improved FD data rates. The key idea is to carefully select the TxBF and RxBF weights to achieve wideband RF SIC in the spatial domain with minimal TxBF and RxBF gain losses. Essentially, TxBF and RxBF are repurposed, thereby not requiring specialized RF canceller circuitry. We formulate the corresponding optimization problem and develop an iterative algorithm to obtain an approximate solution with provable performance guarantees. Using SI channel measurements and datasets, we extensively evaluate the performance of the proposed approach in different use cases under various network settings. The results show that an FD phased array with 9/36/72 elements can cancel the total SI power to below the noise floor with sum TxBF and RxBF gain losses of 10.6/7.2/6.9 dB, even at Tx power level of 30 dBm. Moreover, the corresponding FD rate gains are at least 1.33/1.66/1.68× 
    more » « less
  4. Purpose

    In this work, we investigated how the position of the radiofrequency (RF) shield can affect the signal‐to‐noise ratio (SNR) of a receive RF coil. Our aim was to obtain physical insight for the design of a 10.5T 32‐channel head coil, subject to the constraints on the diameter of the RF shield imposed by the head gradient coil geometry.

    Method

    We used full‐wave numerical simulations to investigate how the SNR of an RF receive coil depends on the diameter of the RF shield at ultra‐high magnetic field (UHF) strengths (≥7T).

    Results

    Our simulations showed that there is an SNR‐optimal RF shield size at UHF strength, whereas at low field the SNR monotonically increases with the shield diameter. For a 32‐channel head coil at 10.5T, an optimally sized RF shield could act as a cylindrical waveguide and increase the SNR in the brain by 27% compared to moving the shield as far as possible from the coil. Our results also showed that a separate transmit array between the RF shield and the receive array could considerably reduce SNR even if they are decoupled.

    Conclusion

    At sufficiently high magnetic field strength, the design of local RF coils should be optimized together with the design of the RF shield to benefit from both near field and resonant modes.

     
    more » « less
  5. Physical unclonable functions (PUF) in silicon exploit die-to-die manufacturing variations during fabrication for uniquely identifying each die. Since it is practically a hard problem to recreate exact silicon features across dies, a PUF-based authentication system is robust, secure and cost-effective, as long as bias removal and error correction are taken into account. In this work, we utilize the effects of inherent process variation on analog and radio-frequency (RF) properties of multiple wireless transmitters (Tx) in a sensor network, and detect the features at the receiver (Rx) using a deep neural network based framework. The proposed mechanism/ framework, called RF-PUF, harnesses already-existing RF communication hardware and does not require any additional PUF-generation circuitry in the Tx for practical implementation. Simulation results indicate that the RF-PUF framework can distinguish up to 10000 transmitters (with standard foundry defined variations for a 65 nm process, leading to non-idealities such as LO offset and I-Q imbalance) under varying channel conditions, with a probability of false detection <10^-3 
    more » « less