An official website of the United States government
The ability to observe astronomical events through the detection of gravitational waves relies on the quality of multilayer coatings used on the optical mirrors of interferometers. Amorphous Ta2O5 (including TiO2:Ta2O5) currently limits detector sensitivity due to high mechanical loss. In this paper, mechanical loss measured at both cryogenic and room temperatures of amorphous Ta2O5 films grown by magnetron sputtering and annealed in air at 500 ◦C is shown to decrease for elevated growth temperature. Films grown at 310 ◦C and annealed yield a mechanical loss of 3.1×10−4 at room temperature, the lowest value reported for pure amorphous Ta2O5 grown by magnetron sputtering to date, and comparable to the lowest values obtained for films grown by ion beam sputtering. Additionally, the refractive index n increases 6% for elevated growth temperature, which could lead to improved sensitivity of gravitational-wave detectors by allowing a thickness reduction in the mirrors’ coatings. Structural characterization suggests that the observed mechanical loss reduction in amorphous Ta2O5 films with increasing growth temperature correlates with a reduction in the coordination number between oxygen and tantalum atoms, consistent with TaOx polyhedra with increased corner-sharing and reduced edge- and facesharing structures.
more »
« less
Exploration of co-sputtered Ta 2 O 5 –ZrO 2 thin films for gravitational-wave detectors
Abstract We report on the development and extensive characterization of co-sputtered tantala–zirconia (Ta 2 O 5 -ZrO 2 ) thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio η = Zr/(Zr + Ta) and of post-deposition heat treatment temperature T a on the optical and mechanical properties of the films. Co-sputtered zirconia proved to be an efficient way to frustrate crystallization in tantala thin films, allowing for a substantial increase of the maximum annealing temperature and hence for a decrease of coating mechanical loss φ c . The lowest average coating loss was observed for an ion-beam sputtered sample with η = 0.485 ± 0.004 annealed at 800 °C, yielding φ ¯ c = 1.8 × 1 0 − 4 rad. All coating samples showed cracks after annealing. Although in principle our measurements are sensitive to such defects, we found no evidence that our results were affected. The issue could be solved, at least for ion-beam sputtered coatings, by decreasing heating and cooling rates down to 7 °C h −1 . While we observed as little optical absorption as in the coatings of current gravitational-wave interferometers (0.5 parts per million), further development will be needed to decrease light scattering and avoid the formation of defects upon annealing.
more »
« less
- PAR ID:
- 10354101
- Author(s) / Creator(s):
- ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; more »
- Date Published:
- Journal Name:
- Classical and Quantum Gravity
- Volume:
- 38
- Issue:
- 19
- ISSN:
- 0264-9381
- Page Range / eLocation ID:
- 195021
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract We report on the structure and dielectric properties of ternary A6B2O17(A = Zr; B = Nb, Ta) thin films and ceramics. Thin films are produced via sputter deposition from dense, phase‐homogenous bulk ceramic targets, which are synthesized through a reactive sintering process at 1500°C. Crystal structure, microstructure, chemistry, and dielectric properties are characterized by X‐ray diffraction and reflectivity, atomic force microscopy, X‐ray photoelectron spectroscopy, and capacitance analysis, respectively. We observe relative permittivities approaching 60 and loss tangents <1 × 10−2across the 103–105 Hz frequency range in the Zr6Nb2O17and Zr6Ta2O17phases. These observations create an opportunity space for this novel class of disordered oxide electroceramics.more » « less
-
High-quality optical coatings with low mechanical and optical losses are essential for the sensitivity of gravitational-wave detectors. While annealing is required to reduce the mechanical loss of amorphous coating materials, it often induces crystallization, which degrades optical performance through increased scattering. Standard characterization techniques, such as X-ray diffraction, are limited in detecting sparse populations of crystallites or characterizing their individual size distributions. In this work, we demonstrate a supplementary method based on angle-resolved Rayleigh–Mie scattering to detect and characterize individual crystallites within an amorphous coating. We apply this technique to a titanium-doped germania (GeO2:TiO2) coating, a promising material for future detectors, subjected to stepwise annealing at 625∘C. By comparing measured differential scattering cross-sections to T-matrix simulations, we extract the radius of individual defects and successfully monitor the evolution of the emerging defect population as a function of annealing. This technique allows for the detection of crystallites or other defects with radii down to ≈80nm and provides a complementary tool for studying the early stages of crystallization in low-noise optical coatings.more » « less
-
High-performance optical interference coatings have transformed precision interferometry and spectroscopy by enabling unparalleled control over light–matter interactions. This review explores recent innovations in ion-beam sputtered amorphous dielectric, as well as substrate-transferred crystalline coatings, and their impact on systems at the forefront of precision metrology. These state-of-the-art coating techniques generate multilayers with ultralow optical losses, yielding mirrors with exceptional reflectivity. Refinements in their noise performance push the ultimate limits of sensitivity, resolution, and stability in demanding laser-based metrology applications. These technologies underpin the most advanced timekeeping and spatial measurement tools, enabling high-finesse reference cavities for the world’s most precise optical atomic clocks and low-noise reflective test masses for km-baseline gravitational-wave detectors. Emerging hybrid designs combining these techniques expand access to the mid-infrared spectral region, enabling the first ultralow-optical-loss coatings in the 3000–5000 nm wavelength range for enhanced spectroscopy and trace-gas detection. We highlight how these technologies redefine coating performance metrics and set new benchmarks in quantum science, fundamental physics, and precision optical sensing.more » « less
-
The characteristics of sputtered NiO for use in pn heterojunctions with Ga 2 O 3 were investigated as a function of sputtering parameters and postdeposition annealing temperature. The oxygen/ nickel and Ni 2 O 3 /NiO ratios, as well as the bandgap and resistivity, increased as a function of O 2 /Ar gas flow ratio. For example, the bandgap increased from 3.7 to 3.9 eV and the resistivity increased from 0.1 to 2.9 Ω cm for the O 2 /Ar ratio increasing from 1/30 to 1/3. By sharp contrast, the bandgap and Ni 2 O 3 /NiO ratio decreased monotonically with postdeposition annealing temperatures up to 600 °C, but the density of films increased due to a higher fraction of NiO being present. Hydrogen is readily incorporated into NiO during exposure to plasmas, as delineated by secondary ion mass spectrometry measurements on deuterated films. The band alignments of NiO films were type II-staggered gaps with both α- and β-Ga 2 O 3 . The breakdown voltage of NiO/β-Ga 2 O 3 heterojunction rectifiers was also a strong function of the O 2 /Ar flow ratio during deposition, with values of 1350 V for 1/3 and 830 V for 1/30.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1088/1361-6382/ac1b06
