Single-photon avalanche diodes (SPADs) that are sensitive to photons in the Short-wave infrared and extended short-wave infrared (SWIR and eSWIR) spectra are important components for communication, ranging, and low-light level imaging. The high gain, low excess noise factor, and widely tunable bandgap of AlxIn1-xAsySb1-yavalanche photodiodes (APDs) make them a suitable candidate for these applications. In this work, we report single-photon-counting results for a separate absorption, charge, and multiplication (SACM) Geiger-mode SPAD within a gated-quenching circuit. The single-photon avalanche probabilities surpass 80% at 80 K, corresponding with single-photon detection efficiencies of 33% and 12% at 1.55 µm and 2 µm, respectively.
Dynamic-quenching of a single-photon avalanche photodetector using an adaptive resistive switch
Abstract One of the most common approaches for quenching single-photon avalanche diodes is to use a passive resistor in series with it. A drawback of this approach has been the limited recovery speed of the single-photon avalanche diodes. High resistance is needed to quench the avalanche, leading to slower recharging of the single-photon avalanche diodes depletion capacitor. We address this issue by replacing a fixed quenching resistor with a bias-dependent adaptive resistive switch. Reversible generation of metallic conduction enables switching between low and high resistance states under unipolar bias. As an example, using a Pt/Al 2 O 3 /Ag resistor with a commercial silicon single-photon avalanche diodes, we demonstrate avalanche pulse widths as small as ~30 ns, 10× smaller than a passively quenched approach, thus significantly improving the single-photon avalanche diodes frequency response. The experimental results are consistent with a model where the adaptive resistor dynamically changes its resistance during discharging and recharging the single-photon avalanche diodes.
more »
« less
- NSF-PAR ID:
- 10356986
- Date Published:
- Journal Name:
- Nature Communications
- Volume:
- 13
- Issue:
- 1
- ISSN:
- 2041-1723
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
Superconducting nanowire single photon detectors are typically biased using a constant current source and shunted in a conductance that is over an order of magnitude larger than the peak normal domain conductance of the detector. While this design choice is required to ensure quenching of the normal domain, the use of a small load resistor limits the pulse amplitude, rising-edge slew rate, and recovery time of the detector. Here, we explore the possibility of actively quenching the normal domain, thereby removing the need to shunt the detector in a small resistance. We first consider the theoretical performance of an actively quenched superconducting nanowire single photon detector and, in comparison to a passively quenched device, we predict roughly an order of magnitude improvement in the slew rate and peak voltage achieved in this configuration. The experimental performance of actively and passively quenched superconducting nanowire single photon detectors are then compared. It is shown that, in comparison to a passively quenched device, the actively quenched detectors simultaneously exhibited improved count rates, dark count rates, and timing jitter.
-
more » « less
Abstract Active 3D imaging systems have broad applications across disciplines, including biological imaging, remote sensing and robotics. Applications in these domains require fast acquisition times, high timing accuracy, and high detection sensitivity. Single-photon avalanche diodes (SPADs) have emerged as one of the most promising detector technologies to achieve all of these requirements. However, these detectors are plagued by measurement distortions known as pileup, which fundamentally limit their precision. In this work, we develop a probabilistic image formation model that accurately models pileup. We devise inverse methods to efficiently and robustly estimate scene depth and reflectance from recorded photon counts using the proposed model along with statistical priors. With this algorithm, we not only demonstrate improvements to timing accuracy by more than an order of magnitude compared to the state-of-the-art, but our approach is also the first to facilitate sub-picosecond-accurate, photon-efficient 3D imaging in practical scenarios where widely-varying photon counts are observed.
-
Abstract CdS nanowires and film Schottky diodes are fabricated and diode properties are compared. Effect of SnO 2 on CdS film diode properties is investigated. CdS film/Au on 100 nm SnO 2 substrate demonstrates like-resistor characteristics and increase in SnO 2 thickness corrects resistor behavior, however the effective reverse saturation current density J o is significantly high and shunt resistance are considerably low, implying that SnO 2 slightly prevents impurities migration from CdS films into ITO but cause additional issues. Thickness of CdS film on diode properties is further investigated and increasing CdS film thickness improved J o by one order of magnitude, however shunt resistance is obviously low, suggesting intrinsic issues in CdS film. 100 nm CdS nanowire/Au diodes reduce J o by three orders of magnitude in the dark and two orders of magnitude in the light respectively and their shunt resistance is significantly enhanced by 70 times when comparing with those of the CdS film diodes. The wide difference can be attributed to the fact that CdS nanowires overcome intrinsic issues in CdS film and thus demonstrate significantly well- defined diode behavior. Simulation found that CdS nanowire diodes have low compensating acceptor type traps and interface state density of 5.0 × 10 9 cm −2 , indicating that interface recombination is not a dominated current transport mechanism in the nanowire diodes. CdS film diodes are simulated with acceptor traps and interface state density increased by two order of magnitude and shunt resistance reduced by one order of magnitude, indicating that high density of interface states and shunt paths occur in the CdS film diodes.more » « less
-
This work demonstrates a novel junction termination extension (JTE) with a graded charge profile for vertical GaN p-n diodes. The fabrication of this JTE obviates GaN etch and requires only a single-step implantation. A bi-layer photoresist is used to produce an ultra-small bevel angle (~0.1°) at the sidewall of a dielectric layer. This tapered dielectric layer is then used as the implantation mask to produce a graded charge profile in p-GaN. The fabricated GaN p-n diodes show a breakdown voltage ( BV ) of 1.7 kV (83% of the parallel-plane limit) with positive temperature coefficient, as well as a high avalanche current density over 1100 A/cm 2 at BV in the unclamped inductive switching test. This robust avalanche is ascribed to the migration of the major impact ionization location from the JTE edge to the main junction. This single-implant, efficient, avalanche-capable JTE can potentially become a building block of many vertical GaN devices, and its fabrication technique has wide device and material applicability.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1038/s41467-022-29195-7
