More Like this

1. Spherical Particles in As-prepared Al ₆₅ Cu ₂₅ Fe ₁₅ Alloy by Arc-melting

   https://doi.org/10.1017/S1431927620014002  

   Marshall, Jeremy; Duley, Heavenly; Homan, Joshua; Klein, Clay; Li, Chunfei (July 2020, Microscopy and Microanalysis)

   null (Ed.)
2. Compositional Optimization of Alloy Fe _x Ni _y (OH) ₂ Nanoparticles for Alkaline Electrochemical Oxygen Evolution

   https://doi.org/10.1149/07709.0025ecst  

   Greenlee, Lauren F; Acharya, Prashant; Nelson, Zachary (May 2017, ECS Transactions)

   null (Ed.)
3. Temperature-dependent mechanical behavior of an Al _0.5 Cr _0.9 FeNi _2.5 V _0.2 high-entropy alloy

   https://doi.org/10.1063/5.0064821  

   Zhou, Shichao; Liaw, Peter K.; Xue, Yunfei; Zhang, Yong (September 2021, Applied Physics Letters)
4. Bifunctional Ultrathin RhRu _0.5 ‐Alloy Nanowire Electrocatalysts for Hydrazine‐Assisted Water Splitting

   https://doi.org/10.1002/adma.202301533  

   Fu, Xiaoyang; Cheng, Dongfang; Wan, Chengzhang; Kumari, Simran; Zhang, Hongtu; Zhang, Ao; Huyan, Huaixun; Zhou, Jingxuan; Ren, Huaying; Wang, Sibo; et al (April 2023, Advanced Materials)

   Abstract Hydrazine‐assisted water electrolysis offers a feasible path for low‐voltage green hydrogen production. Herein, the design and synthesis of ultrathin RhRu_0.5‐alloy wavy nanowires as bifunctional electrocatalysts for both the anodic hydrazine oxidation reaction (HzOR) and the cathodic hydrogen evolution reaction (HER) is reported. It is shown that the RhRu_0.5‐alloy wavy nanowires can achieve complete electrooxidation of hydrazine with a low overpotential and high mass activity, as well as improved performance for the HER. The resulting RhRu_0.5bifunctional electrocatalysts enable, high performance hydrazine‐assisted water electrolysis delivering a current density of 100 mA cm⁻²at an ultralow cell voltage of 54 mV and a high current density of 853 mA cm⁻²at a cell voltage of 0.6 V. The RhRu_0.5 electrocatalysts further demonstrate a stable operation at a high current density of 100 mA cm⁻²for 80 hours of testing period with little irreversible degradation. The overall performance greatly exceeds that of the previously reported hydrazine‐assisted water electrolyzers, offering a pathway for efficiently converting hazardous hydrazine into molecular hydrogen. 

   more » « less
5. Radiation Damage Mitigation in FeCrAl Alloy at Sub-Recrystallization Temperatures

   https://doi.org/10.3390/ma18010124  

   Rahman, Md Hafijur; Rasel, Md_Abu Jafar; Smyth, Christopher M; Waryoba, Daudi; Haque, Aman (January 2025, Materials)

   Traditional defect recovery methods rely on high-temperature annealing, often exceeding 750 °C for FeCrAl. In this study, we introduce electron wind force (EWF)-assisted annealing as an alternative approach to mitigate irradiation-induced defects at significantly lower temperatures. FeCrAl samples irradiated with 5 MeV Zr2+ ions at a dose of 1014 cm−2 were annealed using EWF at 250 °C for 60 s. We demonstrate a remarkable transformation in the irradiated microstructure, where significant increases in kernel average misorientation (KAM) and low-angle grain boundaries (LAGBs) typically indicate heightened defect density; the use of EWF annealing reversed these effects. X-ray diffraction (XRD) confirmed these findings, showing substantial reductions in full width at half maximum (FWHM) values and a realignment of peak positions toward their original states, indicative of stress and defect recovery. To compare the effectiveness of EWF, we also conducted traditional thermal annealing at 250 °C for 7 h, which proved less effective in defect recovery as evidenced by less pronounced improvements in XRD FWHM values. 

   more » « less