Active acoustic metamaterials are one path to acoustic properties difficult to realize with passive structures, especially for broadband applications. Here, we experimentally demonstrate a 2D metamaterial composed of coupled sensor-driver unit cells with effective bulk modulus ([Formula: see text]) precisely tunable through adjustments of the amplitude and phase of the transfer function between pairs of sensors and drivers present in each cell. This work adopts the concepts of our previous theoretical study on polarized sources to realize acoustic metamaterials in which the active unit cells are strongly interacting with each other. To demonstrate the capability of our active metamaterial to produce on-demand negative, fractional, and large [Formula: see text], we matched the scattered field from an incident pulse measured in a 2D waveguide with the sound scattered by equivalent continuous materials obtained in numerical simulations. Our approach benefits from being highly scalable, as the unit cells are independently controlled and any number of them can be arranged to form arbitrary geometries without added computational complexity.
more »
« less
Negative‐Index Acoustic Metamaterial Operating above 100 kHz in Water Using Microstructured Silicon Chips as Unit Cells
A major challenge for negative‐index acoustic metamaterials is increasing their operational frequency to the MHz range in water for applications such as biomedical ultrasound. Herein, a novel technology to realize acoustic metamaterials in water using microstructured silicon chips as unit cells that incorporate silicon nitride membranes and Helmholtz resonators with dimensions below 100 μm fabricated using clean‐room microfabrication technology is presented. The silicon chip unit‐cells are then assembled to form periodic structures that result in a negative‐index metamaterial. Finite‐element method (FEM) simulations of the metamaterial show a negative‐index branch in the dispersion relation in the 0.25–0.35 MHz range. The metamaterial is characterized experimentally using laser‐doppler vibrometry, showing opposite phase and group velocities, a signature of negative‐index materials, and is in close agreement with FEM simulations. The experimental measurements also show that the magnitude of phase and group velocities increase as the frequency increases within the negative‐index band, confirming the negative‐index behavior of the material. Acoustic indices from –1 to –5 are reached with respect to water in the 0.25–0.35 MHz range. The use of silicon technology microfabrication to produce acoustic metamaterials for operation in water opens a new road to reach frequencies relevant for biomedical ultrasound applications.
more » « less- NSF-PAR ID:
- 10368467
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials Technologies
- Volume:
- 7
- Issue:
- 12
- ISSN:
- 2365-709X
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
more » « less
Abstract Acoustic holograms have promising applications in sound‐field reconstruction, particle manipulation, ultrasonic haptics, and therapy. This study reports on the theoretical, numerical, and experimental investigation of multiplexed acoustic holograms at both audio and ultrasonic frequencies via a rationally designed transmission‐type acoustic metamaterial. The proposed metahologram is composed of two Fabry–Pérot resonant channels per unit cell, which enables the simultaneous modulation of the transmitted amplitude and phase at two desired frequencies. In contrast to conventional acoustic metamaterial‐based holograms, the design strategy proposed here provides a new degree of freedom (frequency) that can actively tailor holograms that are otherwise completely passive and significantly enhances the information encoded in acoustic metamaterials. To demonstrate the multiplexed acoustic metamaterial, the projection of two different high‐quality metaholograms is first shown at 14 and 17 kHz, with the patterns of the letters N and S. Then, two‐channel ultrasound focusing and annular beams generation for the incident ultrasonic frequencies of 35 and 42.5 kHz are demonstrated. These multiplexed acoustic metaholograms offer a technical advance to tackle the rising challenges in the fields of acoustic metamaterials, architectural acoustics, and medical ultrasound.
-
Kareh, Kristina (Ed.)Mechanical metamaterials at the microscale exhibit exotic static properties owing to their en- gineered building blocks, but their dynamic properties have remained significantly less explored. Their design principles can target frequency-dependent properties and resilience upon high-strain-rate deformation, making them versatile materials for applications in lightweight impact resistance, acoustic waveguiding, or vibration damping. However, accessing dynamic properties at small scales has remained a challenge due to low-throughput and destructive characterization, or lack of existing testing protocols. Here we demonstrate a high-throughput non-contact framework that employs MHz-wave propagation signatures within a metamaterial to nondestructively extract dynamic linear properties, omnidirectional elastic information, damping properties, and defect quantification. Using rod-like tessellations of microscopic metamaterials, we report up to 94% direction- and rate-dependent dynamic stiffening at strain rates approaching 10^2 s^{−1}, in addition to damping properties 3 times higher than their constituent materials. We also show that frequency shifts in the vibrational response allow for characterization of invisible defects within the metamaterials, and that selective probing allows for construction of experimental elastic surfaces, previously only possible computationally. Our work provides a route for accelerated data-driven discovery of materials and microdevices for dynamic applications such as protective structures, medical ultrasound, or vibration isolation.more » « less
-
more » « less
Active acoustic metamaterials incorporate electric circuit elements that input energy into an otherwise passive medium to aptly modulate the effective material properties. Here, we propose an active acoustic metamaterial with Willis coupling to drastically extend the tunability of the effective density and bulk modulus with the accessible parameter range enlarged by at least two orders of magnitude compared to that of a non-Willis metamaterial. Traditional active metamaterial designs are based on local resonances without considering the Willis coupling that limit their accessible effective material parameter range. Our design adopts a unit cell structure with two sensor-transducer pairs coupling the acoustic response on both sides of the metamaterial by detecting incident waves and driving active signals asymmetrically superimposed onto the passive response of the material. The Willis coupling results from feedback control circuits with unequal gains. These asymmetric feedback control circuits use Willis coupling to expand the accessible range of the effective density and bulk modulus of the metamaterial. The extreme effective material parameters realizable by the metamaterials will remarkably broaden their applications in biomedical imaging, noise control, and transformation acoustics-based cloaking.
-
null (Ed.)Many engineering applications leverage metamaterials to achieve elastic wave control. To enhance the performance and expand the functionalities of elastic waveguides, the concepts of electronic transport in topological insulators have been applied to elastic metamaterials. Initial studies showed that topologically protected elastic wave transmission in mechanical metamaterials could be realized that is immune to backscattering and undesired localization in the presence of defects or disorder. Recent studies have developed tunable topological elastic metamaterials to maximize performance in the presence of varying external conditions, adapt to changing operating requirements, and enable new functionalities such as a programmable wave path. However, a challenge remains to achieve a tunable topological metamaterial that is comprehensively adaptable in both the frequency and spatial domains and is effective over a broad frequency bandwidth that includes a subwavelength regime. To advance the state of the art, this research presents a piezoelectric metamaterial with the capability to concurrently tailor the frequency, path, and mode shape of topological waves using resonant circuitry. In the research presented in this manuscript, the plane wave expansion method is used to detect a frequency tunable subwavelength Dirac point in the band structure of the periodic unit cell and discover an operating region over which topological wave propagation can exist. Dispersion analyses for a finite strip illuminate how circuit parameters can be utilized to adjust mode shapes corresponding to topological edge states. A further evaluation provides insight into how increased electromechanical coupling and lattice reconfiguration can be exploited to enhance the frequency range for topological wave propagation, increase achievable mode localization, and attain additional edge states. Topological guided wave propagation that is subwavelength in nature and adaptive in path, localization, and frequency is illustrated in numerical simulations of thin plate structures. Outcomes from the presented work indicate that the easily integrable and comprehensively tunable proposed metamaterial could be employed in applications requiring a multitude of functions over a broad frequency bandwidth.more » « less
