skip to main content
Explore Scholarly Publications and Datasets in the NSF-PAR

This content will become publicly available on April 1, 2023

Title: Time-Dependent Behavior of Reinforced Concrete Beams under High Sustained Loads
High levels of sustained load can lead to time-dependent failure of reinforced concrete (RC) members. This in turn may lead to collapse of all or part of a building. Design errors, construction errors, and material deterioration may lead to concrete elements being subjected to high levels of sustained loads well exceeding typical service loads. Plain concrete can experience compressive failure when subjected to a high sustained stress (over 75% of its short-term strength). However, there is a lack of knowledge about the time-dependent strength and stiffness characteristics of RC members under high sustained loads. This paper presents the results of experimental testing of simply supported shear-controlled RC beams under high sustained loads. Two series of beams, consisting of 4 and 5 beams, were tested at concrete ages of 67 to 543 days to represent in-service concrete structures. The applied sustained loads ranged from 82% to 98% of the short-term capacity and lasted for 24 to 52 days. Test results indicated that high sustained load may eventually lead to failure (collapse); however, the level of load needs to be very close (~98%) to the short-term capacity. Under sustained load, all specimens experienced increased deflection with over half of the deflection increase more » occurring in the first 24 h. The sustained load increased the deflection at shear failure by 190% on average. The increase in the beam deflection may allow for load redistribution in redundant structural systems. A sharp increase in deflection due to tertiary creep occurred in a short time (~2 min) before failure, indicating little warning of the impending failure. « less
Authors:
; ; ;
Award ID(s):
1760915
Publication Date:
NSF-PAR ID:
10374019
Journal Name:
Applied Sciences
Volume:
12
Issue:
8
Page Range or eLocation-ID:
4015
ISSN:
2076-3417
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ( , 2020 Structures Congress)
    Design and construction errors and material deterioration can lead to concrete elements being subjected to high levels of sustained stress well exceeding typical service levels. These high levels of sustained stress have led to structural collapses in the United States and around the world. However, the performance of shear-controlled concrete elements (beams and slab-column connections) under high sustained stress is not well understood. Under high sustained compressive stress (greater than 0.75fc’) concrete will suffer tertiary creep characterized by accelerated permanent strain, leading eventually to a failure. The bond of the reinforcing bars to the concrete is also affected leading to slip. This research presents the results of experimental tests on shear-controlled RC beams that were loaded to 81, 86, and 92 percent of their short-term capacity and observed for about four weeks. Deflection and strain measurements were recorded for each specimen throughout the sustained load test. Under high sustained stress the specimens showed continued deflection with time, with most of the deflection occurring shortly after the application of load. The failure of the specimens exhibited more flexural response than that of the control specimen. The test results show that high levels of sustained stress (up to 92% of their short-termmore »capacity) can be sustained for a prolonged time; however, the deflections and cracking are increased and the ultimate failure mode may be changed. This information will help engineers identify elements nearing failure under high levels of sustained stress.« less
  2. ; ; ; ( , ASEE annual conference exposition)
    Most undergraduate civil engineering programs include an introductory course in reinforced concrete design. The course generally includes an introduction to the fundamentals of reinforced concrete behavior, the design of simple beams and one-way slabs to resist shear and flexure, and the design of short columns. Because of the scale of typical civil engineering structures, students commonly do not get to experience large or full-scale structural behavior as a part of an undergraduate reinforced concrete course. Rather, students typically learn fundamental concepts through theoretical discussions, small demonstrations, or pictures and images. Without the interaction with full-scale structural members, students can struggle to develop a clear understanding of the fundamental behavior of these systems such as the differences in behavior of an over or under-reinforced beam. Additionally, students do not build an appreciation for the variations between as-built versus theoretical designs. Large-scale models can illustrate such behavior and enhance student understanding, but most civil engineering programs lack the physical equipment to perform testing at this scale. The authors from St. Louis University (SLU) and Rose-Hulman Institute of Technology (RHIT) have designed and implemented large-scale tests for in-class use that allow students to experience fundamental reinforced concrete behavior. Students design and test severalmore »reinforced concrete members using a modular strong-block testing system. This paper provides a detailed overview of the design, fabrication, and implementation of three large-scale experiential learning modules for an undergraduate reinforced concrete design course. The first module focuses on service load and deflections of a reinforced concrete beam. The first and second modules also focus on flexural failure modes and ductility. The third module focuses on shear design and failure modes. Each module uses a large scale reinforced concrete beam (Flexure specimens: 12 in. x 14 in. x 19 ft, Shear specimens: 12 in. x 14 in. x 10 ft.) that was tested on a modular strong-block testing system. The three modules were used throughout the reinforced concrete design course at SLU and RHIT to illustrate behavior concurrent to the presentation of various reinforced concrete design concepts.« less
  3. ( , Advances in Engineering Materials, Structures and Systems: Innovations, Mechanics and Applications)
    Fiber reinforced polymer (FRP) waste is becoming an environmental concern due to the widespread use and non-biodegradable nature of FRP composites. Cutting FRP waste into discrete reinforce-ments (referred to as “needles” hereafter) as coarse aggregate in concrete has been suggested as a possible solution to FRP waste recycling. It has previously been observed in small specimens that FRP needles increase the tensile strength and energy absorption capacity of concrete. This paper presents an experimental investiga-tion into the effect of GFRP needles as coarse aggregate partial replacement in concrete on shear behavior of full-scale reinforced concrete (RC) beams. A total of 10 RC beams without steel stirrups in the critical zone were tested under four-point bending. The volume replacement ratio of the coarse aggregate and the surface type of GFRP needles were chosen as the test parameters. GFRP needles, with either smooth or helically wrapped surfaces, were added to the concrete mix to replace 5% or 10% of coarse aggregate by volume, respectively. All test beams failed in shear in a brittle manner with the ductility being slightly enhanced by the partial replace-ment of coarse aggregate using GFRP needles. An enhancement of 8%-10% in the load carrying capacity was observed inmore »beams with helically wrapped needles, while beams with smooth needles showed a reduction in the load carrying capacity.« less
  4. ; ( , ASME IMECE 2021)
    LEGOs are one of the most popular toys and are known to be useful as instructional tools in STEM education. In this work, we used LEGO structures to demonstrate the energetic size effect on structural strength. Many material's fexural strength decreases with increasing structural size. We seek to demonstrate this effect in LEGO beams. Fracture experiments were performed using 3-point bend beams built of 2 X 4 LEGO blocks in a periodic staggered arrangement. LEGO wheels were used as rollers on either ends of the specimens which were weight compensated by adding counterweights. [1] Specimens were loaded by hanging weights at their midspan and the maximum sustained load was recorded. Specimens with a built-in defect (crack) of half specimen height were considered. Beam height was varied from two to 32 LEGO blocks while keeping the in-plane aspect ratio constant. The specimen thickness was kept constant at one LEGO block. Slow-motion videos and sound recordings of fractures were captured to determine how the fracture originated and propagated through the specimen. Flexural stress was calculated based on nominal specimen dimensions and fracture toughness was calculated following ASTM E-399 standard expressions from Srawley (1976). [2] The results demonstrate that the LEGO beams indeedmore »exhibit a size effect on strength. For smaller beams the Uexural strength is higher than for larger beams. The dependence of strength on size is similar to that of Bažant’s size effect law [3] . Initiation of failure occurs consistently at the built-in defect. The staggered arrangement causes persistent crack branching which is more pronounced in larger specimens. The results also show that the apparent fracture toughness increases as the specimen size decreases. Further ongoing investigations consider the effects of the initial crack length on the size effect and the fracture response. The present work demonstrates that LEGO structures can serve as an instructional tool. We demonstrate principles of non-linear elastic fracture mechanics and highlight the importance of material microstructure (architecture) in fracture response. The experimental method is reproducible in a classroom setting without the need for complex facilities. This work was partially supported by the National Science Foundation (NSF) under the award #1662177 and the School of Mechanical Engineering at Purdue University. The authors acknowledge the support of Dr. Thomas Siegmund and Glynn Gallaway. [1] Khalilpour, S., BaniAsad, E. and Dehestani, M., 2019. A review on concrete fracture energy and effective parameters. Cement and Concrete research, 120, pp.294-321. [2] Srawley, J.E., 1976, January. Wide range stress intensity factor expressions for ASTM E 399 standard fracture toughness specimens. In Conf. of Am. Soc. for Testing and Mater., Committee E-24 (No. E-8654). [3] Bažant, Z.P., 1999. Size effect on structural strength: a review. Archive of applied Mechanics, 69(9), pp.703-725.« less
  5. ; ; ( , Materials)
    There are ongoing research efforts directed at addressing strength limitations of compressed earth blocks (CEB) that inhibit their deployment for structural applications, particularly in areas where masonry systems are regularly subjected to lateral loads from high winds. In this paper, the authors focus specifically on the extent to which polypropylene (PP) fibers can be used to enhance the flexural performance of CEB. Cementitious matrices used for CEB production exhibit low tensile and flexural strength (brittle) properties. This work investigates plain (unreinforced) and fiber-reinforced specimens (short flexural beams) with fiber mass content of 0.2, 0.4, 0.6, 0.8, and 1.0% and ordinary Portland cement (OPC) content of 8%. The influence of the inclusion of fiber was based on tests conducted using the Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (ASTM C1609). Material properties that were quantified included first-peak strength, peak strength, equivalent flexural strength, residual strength, and flexural toughness. There was an observed improvement in the performance of the soil-fiber matrixes based on these results of these tests. It was also observed that when the fiber content exceeded 0.6% and above, specimens exhibited a deflection- hardening behavior; an indication of improvement in ductility. An equivalent flexural strength predictive model ismore »proposed.« less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email