The stability of a horizontally and vertically sheared surface jet is examined, with a focus on the vertical structure of the resultant eddies. Over a flat bottom, the instability is mixed baroclinic/barotropic, producing strong eddies at depth that are characteristically shifted downstream relative to the surface eddies. Baroclinic instability is suppressed over a large slope for retrograde jets (with a flow antiparallel to topographic wave propagation) and to a lesser extent for prograde jets (with flow parallel to topographic wave propagation), as seen previously. In such cases, barotropic (lateral) instability dominates if the jet is sufficiently narrow. This yields surface eddies whose size is independent of the slope but proportional to the jet width. Deep eddies still form, forced by interfacial motion associated with the surface eddies, but they are weaker than under baroclinic instability and are vertically aligned with the surface eddies. A sinusoidal ridge acts similarly, suppressing baroclinic instability and favoring lateral instability in the upper layer. A ridge with a 1-km wavelength and an amplitude of roughly 10 m is sufficient to suppress baroclinic instability. Surveys of bottom roughness from bathymetry acquired with shipboard multibeam echo sounding reveal that such heights are common beneath the Kuroshio, the Antarctic Circumpolar Current, and, to a lesser extent, the Gulf Stream. Consistent with this, vorticity and velocity cross sections from a 1/50° HYCOM simulation suggest that Gulf Stream eddies are vertically aligned, as in the linear stability calculations with strong topography. Thus, lateral instability may be more common than previously thought, owing to topography hindering vertical energy transfer.
Horizontal distribution of the vertically integrated barotropic‐to‐baroclinic energy conversion has been widely studied to examine the generation of internal tides at steep topography. The vertical structure of the energy conversion that provides insights into the associated dynamics, however, is masked by the often used depth‐integrated approach. Here, we reveal the vertical profile of barotropic‐to‐baroclinic energy conversion by employing an idealized ocean model in a slope‐shelf context forced by
- Award ID(s):
- NSF-PAR ID:
- Publisher / Repository:
- DOI PREFIX: 10.1029
- Date Published:
- Journal Name:
- Journal of Geophysical Research: Oceans
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
A three-dimensional inertial model that conserves quasigeostrophic potential vorticity is proposed for wind-driven coastal upwelling along western boundaries. The dominant response to upwelling favorable winds is a surface-intensified baroclinic meridional boundary current with a subsurface countercurrent. The width of the current is not the baroclinic deformation radius but instead scales with the inertial boundary layer thickness while the depth scales as the ratio of the inertial boundary layer thickness to the baroclinic deformation radius. Thus, the boundary current scales depend on the stratification, wind stress, Coriolis parameter, and its meridional variation. In contrast to two-dimensional wind-driven coastal upwelling, the source waters that feed the Ekman upwelling are provided over the depth scale of this baroclinic current through a combination of onshore barotropic flow and from alongshore in the narrow boundary current. Topography forces an additional current whose characteristics depend on the topographic slope and width. For topography wider than the inertial boundary layer thickness the current is bottom intensified, while for narrow topography the current is wave-like in the vertical and trapped over the topography within the inertial boundary layer. An idealized primitive equation numerical model produces a similar baroclinic boundary current whose vertical length scale agrees with the theoretical scaling for both upwelling and downwelling favorable winds.
The flow of tides over rough bathymetry in the deep ocean generates baroclinic motion including internal waves and bottom‐trapped tides. The stresses generated by this motion feedback on the amplitude and phase of the large‐scale tide. Quantifying the stresses associated with tidal flow over abyssal hills is especially important, as this scale of bathymetry is often unresolved in global baroclinic tide models, and the stresses must therefore be parameterized. Here, we extend the previous theoretical work of the authors to determine the amplitude, phasing, and vertical location of the stresses exerted on a flow driven by a time‐periodic body force when it encounters rough bathymetry. The theory compares favorably with a suite of fully nonlinear numerical simulations. It is shown that all topographic stresses are applied directly above the bathymetry, leading to a two‐layer baroclinic flow, with the near‐bottom spatial‐mean flow (the benthic tide) strongly modified by topographic stresses, and the flow at height unperturbed by the presence of topography. Our results provide a framework to improve baroclinic tide models by (i) providing a simple parameterization for the subinertial stress which is currently not included in any models, (ii) establishing that parameterized stresses should be applied in the diffusive boundary layer directly above the topography, independent of where internal tides may dissipate, and (iii) identifying a minimum resolution of ∼10 km for baroclinic tidal models to adequately capture wave resonance effects that can significantly impact the magnitude of the benthic tide.
In the Arctic Ocean, limited measurements indicate that the strongest mixing below the atmospherically forced surface mixed layer occurs where tidal currents are strong. However, mechanisms of energy conversion from tides to turbulence and the overall contribution of tidally driven mixing to Arctic Ocean state are poorly understood. We present measurements from the shelf north of Svalbard that show abrupt isopycnal vertical displacements of 10–50 m and intense dissipation associated with cross‐isobath diurnal tidal currents of
∼0.15 m s −1. Energy from the barotropic tide accumulated in a trapped baroclinic lee wave during maximum downslope flow and was released around slack water. During a 6‐hr turbulent event, high‐frequency internal waves were present, the full 300‐m depth water column became turbulent, dissipation rates increased by a factor of 100, and turbulent heat flux averaged 15 W m −2compared with the background rate of 1 W m −2.
Large-amplitude internal solitary wave (ISW) shoaling, breaking, and run-up was tracked continuously by a dense and rapidly sampling array spanning depths from 500 m to shore near Dongsha Atoll in the South China Sea. Incident ISW amplitudes ranged between 78 and 146 m with propagation speeds between 1.40 and 2.38 m s−1. The ratio between wave amplitude and a critical amplitude
A0controlled breaking type and was related to wave speed cpand depth. Fissioning ISWs generated larger trailing elevation waves when the thermocline was deep and evolved into onshore propagating bores in depths near 100 m. Collapsing ISWs contained significant mixing and little upslope bore propagation. Bores contained significant onshore near-bottom kinetic and potential energy flux and significant offshore rundown and relaxation phases before and after the bore front passage, respectively. Bores on the shallow forereef drove bottom temperature variation in excess of 10°C and near-bottom cross-shore currents in excess of 0.4 m s−1. Bores decelerated upslope, consistent with upslope two-layer gravity current theory, though run-up extent Xrwas offshore of the predicted gravity current location. Background stratification affected the bore run-up, with Xrfarther offshore when the Korteweg–de Vries nonlinearity coefficient αwas negative. Fronts associated with the shoaling local internal tide, but equal in magnitude to the soliton-generated bores, were observed onshore of 20-m depth.