Nanoporous bimetallic Fe–Ag nanoparticles (NPs) were synthesized using a facile chemical reduction method and used to decorate the surface of multi-walled carbon nanotubes (MWCNTs) for hydrogen sorption and storage. The effect of TiO 2 nanoparticles on the hydrogen storage properties of Fe–Ag/CNTs was further studied in detail. For this purpose, several nanocomposites of nanoporous bimetallic Fe–Ag/TiO 2 nanoparticles with different amounts of bimetallic Fe–Ag NPs were prepared via a hydrothermal method. The hydrogen storage capacity of the as-prepared nanocomposites was studied using electrochemical methods. The Fe–Ag/TiO 2 /CNT nanocomposite with 0.04 M bimetallic Fe–Ag NPs showed the highest capacity for hydrogen storage, which was ∼5× higher than that of pristine MWCNTs. The maximum discharge capacity was 2931 mA h g −1 , corresponding to a 10.94 wt% hydrogen storage capacity. Furthermore, a 379% increase in discharge capacity was measured after 20 cycles. These results show that Fe–Ag/TiO 2 /CNT electrodes display superior cycling stability and high reversible capacity, which is attractive for battery applications.
more »
« less
Probing the role of CNTs in Pt nanoparticle/CNT/graphene nanohybrids H 2 sensors
Abstract In the carbon nanotubes film/graphene heterostructure decorated with catalytic Pt nanoparticles using atomic layer deposition (Pt-NPs/CNTs/Gr) H 2 sensors, the CNT film determines the effective sensing area and the signal transport to Gr channel. The former requires a large CNT aspect ratio for a higher sensing area while the latter demands high electric conductivity for efficient charge transport. Considering the CNT’s aspect ratio decreases, while its conductivity increases ( i.e. , bandgap decreases), with the CNT diameter, it is important to understand how quantitatively these effects impact the performance of the Pt-NPs/CNTs/Gr nanohybrids sensors. Motivated by this, this work presents a systematic study of the Pt-NPs/CNTs/Gr H 2 sensor performance with the CNT films made from different constituent CNTs of diameters ranging from 1 nm for single-wall CNTs, to 2 nm for double-wall CNTs, and to 10–30 nm for multi-wall CNTs (MWCNTs). By measuring the morphology and electric conductivity of SWCNT, DWCNT and MWCNT films, this work aims to reveal the quantitative correlation between the sensor performance and relevant CNT properties. Interestingly, the best performance is obtained on Pt-NPs/MWCNTs/Gr H 2 sensors, which can be attributed to the compromise of the effective sensing area and electric conductivity on MWCNT films and illustrates the importance of optimizing sensor design.
more »
« less
- NSF-PAR ID:
- 10382723
- Date Published:
- Journal Name:
- Nano Express
- Volume:
- 3
- Issue:
- 3
- ISSN:
- 2632-959X
- Page Range / eLocation ID:
- 035004
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m-1 K-1 at room temperature for a 9-walled MWCNT. Theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.more » « less
-
more » « less
Abstract Silver nanoparticles (NPs) are the most widely used conductive material throughout the printed electronics space due to their high conductivity and low cost. However, when interfacing with other prominent printed materials, such as semiconducting carbon nanotubes (CNTs) in thin‐film transistors (TFTs), silver is suboptimal when compared to more expensive or less conductive materials. Consequently, there would be significant value to improving the interface of printed silver to CNT films. In this work, the impact of nanostructure morphology on the electrical properties of printed silver and nanotube junctions in CNT‐TFTs is investigated. Three distinct silver morphologies (NPs, nanoflakes – NFs, and nanowires – NWs) are explored with top‐ and bottom‐contact configurations for each. The NF morphology in a top‐contact configuration is found to yield the best electrical interface to CNTs, resulting in an average contact resistance of 1.2 MΩ ⋅ µm. Beyond electrical performance, several trade‐offs in morphology selection are revealed, including print resolution and process temperature. While NF inks produce the best interfaces, NP inks produce the smallest features, and NW inks are compatible with low processing temperatures (<80 °C). These results outline the trade‐offs between silver contact morphologies in CNT‐TFTs and show that contact morphology selection can be tailored for specific applications.
-
more » « less
Abstract The objective of this study is to derive a numerical model of carbon nanotube (CNT)-based thin films that accurately reflect their electrical and electromechanical performance as observed through experimental tests. Although nanocomposites based on CNTs dispersed in polymer matrices have been studied extensively, their nanocomposite properties vary depending on CNT orientations. This study aimed to explain how differences in nanocomposite behavior could be revealed by numerical models considering different CNT alignment conditions. First, a percolation-based thin film model was generated by randomly dispersing CNT elements in a predefined two-dimensional domain. The degree of CNT alignment in the film was controlled by limiting the CNT elements’ maximum angle they make with respect to the film’s longitudinal axis. Then, numerical simulations on CNT-based film models were conducted. Second, multi-walled carbon nanotube (MWCNT)-epoxy films were prepared via drop casting. Alternating current was applied to the MWCNT-epoxy mixture before curing to prepare films with different degrees of CNT alignment. The electrical and electromechanical properties of these specimens were characterized, and the results were compared with simulations. Good agreement between experiments and simulations was observed.
-
more » « less
Abstract Light addressable electrochemical (LAE) sensors have seen great utility in the past several years because they enable multiple localized electrochemical measurements to be performed on a single macroscopic electrode, opening up applications in imaging, biosensing, surface patterning, and multiplexing. In this study, we investigated the effects of electrodeposition on the formation of LAE sensors formed between n‐Si and electrodeposited Pt. We prepared sensors by electrodepositing Pt onto freshly‐etched n‐Si under a variety of conditions, varying the Pt precursor concentration, electrodeposition time, supporting electrolyte, and potential waveform. We characterized the sensors using a combination of atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. This study shows that the electrodeposition parameters have a dramatic impact on the morphology of the electrodeposited surfaces, sensor stability, and sensitivity towards H2O2. Specifically, we observed that continuous Pt films prepared with a higher Pt precursor concentration were more stable and had better linearity, higher sensitivity, and broader dynamic range than those prepared with a lower Pt precursor concentration. The stability and increased H2O2sensing performance correlate strongly with an increase in the Pt islands which make up the film. These data highlight that the morphology of the metal in semiconductor/metal junction LAE sensors has an impact on important performance metrics like stability and sensitivity. They also demonstrate the need for semiconductor/metal LAE sensors to be studied using micro‐ and nanoscale imaging techniques in order to more deeply understand their performance characteristics.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1088/2632-959X/ac843d
