skip to main content


Title: Computational Modeling of Nonlinear Dynamics and Its Utility in MEMS Gyroscopes.
This paper describes a hybrid approach for modeling nonlinear vibrations and determining essential (normal form) coefficients that govern a reduced-order model of a structure. Incorporating both computational and analytical tools, this blended method is demonstrated by considering a micro-electro-mechanical vibrating gyroscopic rate sensor that is actuated by segmented DC electrodes. Two characterization methods are expatiated, where one is more favorable in computational tools and the other can be used in experiments. Using the reduced model, it is shown that tuning the nonuniform DC bias results in favorable changes in Duffing and mode-coupling nonlinearities which can improve the gyroscope angular rate sensitivity by two orders of magnitude.  more » « less
Award ID(s):
1662619
NSF-PAR ID:
10386062
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
Journal of Structural Dynamics
ISSN:
2684-6500
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Hydrodynamic performance of ships can be greatly improved by the formation of air cavities under ship bottom with the purpose to decrease water friction on the hull surface. The air-cavity ships using this type of drag reduction are usually designed for and typically effective only in a relatively narrow range of speeds and hull attitudes and sufficient rates of air supply to the cavity. To investigate the behavior of a small-scale air-cavity boat operating under both favorable and detrimental loading and speed conditions, a remotely controlled model hull was equipped with a data acquisition system, video camera and onboard sensors to measure air-cavity characteristics, air supply rate and the boat speed, thrust and trim in operations on open-water reservoirs. These measurements were captured by a data logger and also wirelessly transmitted to a ground station and video monitor. The experimental air-cavity boat was tested in a range of speeds corresponding to length Froude numbers between 0.17 and 0.5 under three loading conditions, resulting in near zero trim and significant bow-up and bow-down trim angles at rest. Reduced cavity size and significantly increased drag occurred when operating at higher speeds, especially in the bow-up trim condition. The other objective of this study was to determine whether computational fluid dynamics simulations can adequately capture the recorded behavior of the boat and air cavity. A computational software Star-CCM+ was utilized with the VOF method employed for multi-phase flow, RANS approach for turbulence modeling, and economical mesh settings with refinements in the cavity region and near free surface. Upon conducting the mesh verification study, several experimental conditions were simulated, and approximate agreement with measured test data was found. Adaptive mesh refinement and time step controls were also applied to compare results with those obtained on the user-generated mesh. Adaptive controls improved resolution of complex shedding patterns from the air cavity but had little impact on overall results. The presented here experimental approach and obtained results indicate that both outdoor experimentation and computationally inexpensive modeling can be used in the process of developing air-cavity systems for ship hulls. 
    more » « less
  2. null (Ed.)
    To reproduce a Digital Twin (DT) of a data center (DC), input data is required which is collected through site surveys. Data collection is an important step since accurate representation of a DC depends on capturing the necessary detail for various model fidelity levels of each DC component. However, guidance is lacking in this regard as to which components within the DC are crucial to achieve the level of accuracy desired for the computational model. And determining the input values of the component object parameters is an exercise in engineering judgement during site survey. Sensitivity analysis can be an effective methodology to determine how the level of simplification in component models can affect the model accuracy.In this study, a calibrated raised-floor DC model is used to study the sensitivity of a DC component's representation to the DC model accuracy. Commercial CFD tool, 6SigmaDC Room is used for modeling and simulation. A total of 8 DC components are considered and eventually ranked on the basis of time and effort required to collect model input data. For parametrized component object, the object's full range of input parameter values are considered, and simulations run. The results are compared with the baseline calibrated model to understand the trade-off between survey effort/cost and model accuracy. For the calibrated DC model and of the 8 components considered, it was observed that the chilled water piping branches, data cables and the cable penetration seal (found within cabinets) have considerable influence on the tile flow rate prediction accuracy. 
    more » « less
  3. Abstract Obtaining lightweight and accurate approximations of discretized objective functional Hessians in inverse problems governed by partial differential equations (PDEs) is essential to make both deterministic and Bayesian statistical large-scale inverse problems computationally tractable. The cubic computational complexity of dense linear algebraic tasks, such as Cholesky factorization, that provide a means to sample Gaussian distributions and determine solutions of Newton linear systems is a computational bottleneck at large-scale. These tasks can be reduced to log-linear complexity by utilizing hierarchical off-diagonal low-rank (HODLR) matrix approximations. In this work, we show that a class of Hessians that arise from inverse problems governed by PDEs are well approximated by the HODLR matrix format. In particular, we study inverse problems governed by PDEs that model the instantaneous viscous flow of ice sheets. In these problems, we seek a spatially distributed basal sliding parameter field such that the flow predicted by the ice sheet model is consistent with ice sheet surface velocity observations. We demonstrate the use of HODLR Hessian approximation to efficiently sample the Laplace approximation of the posterior distribution with covariance further approximated by HODLR matrix compression. Computational studies are performed which illustrate ice sheet problem regimes for which the Gauss–Newton data-misfit Hessian is more efficiently approximated by the HODLR matrix format than the low-rank (LR) format. We then demonstrate that HODLR approximations can be favorable, when compared to global LR approximations, for large-scale problems by studying the data-misfit Hessian associated with inverse problems governed by the first-order Stokes flow model on the Humboldt glacier and Greenland ice sheet. 
    more » « less
  4. In plasma-driven solution electrolysis (PDSE), gas-phase plasma-produced species interact with an electrolytic solution to produce, for example, nanoparticles. An atmospheric pressure plasma jet (APPJ) directed onto a liquid solution containing a metallic salt will promote reduction of metallic ions in solution, generating metallic clusters that nucleate to form nanoparticles. In this article, results from a computational investigation are discussed of a PDSE process in which a radio-frequency APPJ sustained in helium impinges on a silver nitrate solution, resulting in growth of silver nanoparticles. A reaction mechanism was developed and implemented in a global plasma chemistry model to predict nanoparticle growth. To develop the reaction mechanism, density functional theory was used to generate probable silver growth pathways up to Ag 9 . Neutral clusters larger than Ag 9 were classified as nanoparticles. Kinetic reaction rate coefficients for thermodynamically favorable growth pathways were estimated based on an existing, empirically determined base reaction mechanism for smaller Ag particle interactions. These rates were used in conjunction with diffusion-controlled reaction rate coefficients that were calculated for other Ag species. The role of anions in reduction of Ag n ions in forming nanoparticles is also discussed. Oxygen containing impurities or admixtures to the helium, air entrainment into the APPJ, and dissociation of saturated water vapor above the solution can produce additional reactive oxygen species in solution, resulting in the production of anions and [Formula: see text] in particular. For a given molarity, delivering a sufficient fluence of reducing species will produce similar nanoparticle densities and sizes for all applied power levels. Comparisons are made to alternate models for nanoparticle formation, including charged nanoparticles and use of direct current plasmas. 
    more » « less
  5. Cysteine sulfonic acid (Cys-SO3H; cysteic acid) is an oxidative post-translational modification of cysteine, resulting from further oxidation from cysteine sulfinic acid (Cys- SO2H). Cysteine sulfonic acid is considered an irreversible post-translational modification, which serves as a biomarker of oxidative stress that has resulted in oxidative damage to proteins. Cysteine sulfonic acid is anionic, as a sulfonate (Cys-SO –; cysteate), in the ionization state that 3 is almost exclusively present at physiological pH (pKa ~ –2). In order to understand protein structural changes that can occur upon oxidation to cysteine sulfonic acid, we analyzed its conformational preferences, using experimental methods, bioinformatics, and DFT-based computational analysis. Cysteine sulfonic acid was incorporated into model peptides for α-helix and polyproline II helix (PPII). Within peptides, oxidation of cysteine to the sulfonic acid proceeds rapidly and efficiently at room temperature in solution with methyltrioxorhenium (MeReO3) and H2O2. Peptides containing cysteine sulfonic acid were also generated on solid phase using trityl-protected cysteine and oxidation with MeReO3 and H2O2. Using methoxybenzyl (Mob)-protected cysteine, solid-phase oxidation with MeReO3 and H2O2 generated the Mob sulfone precursor to Cys-SO – within fully synthesized peptides. These two solid-phase methods allow the synthesis of peptides containing either Cys-SO – or Cys-SO – in a 32 practical manner, with no solution-phase synthesis required. Cys-SO – had low PPII propensity 3 for PPII propagation, despite promoting a relatively compact conformation in φ. In contrast, in a PPII initiation model system, Cys-SO – promoted PPII relative to neutral Cys, with PPII initiation similar to Cys thiolate but less than Cys-SO – or Ala. In an α-helix model system, Cys- 2 SO – promoted α-helix near the N-terminus, due to favorable helix dipole interactions and 3 favorable α-helix capping via a sulfonate-amide side chain-main chain hydrogen bond. Across all peptides, the sulfonate side chain was significantly less ordered than that of the sulfinate. Analysis of Cys-SO – in the PDB revealed a very strong propensity for local (i/i or i/i+1) side 3 chain-main chain sulfonate-amide hydrogen bonds for Cys-SO –, with > 80% of Cys-SO – 33 residues exhibiting these interactions. DFT calculations conducted to explore these conformational preferences indicated that side chain-main chain hydrogen bonds of the sulfonate with the intraresidue amide and/or with the i+1 amide were favorable. However, hydrogen bonds to water or to amides, as well as interactions with oxophilic metals, were weaker for the sulfonate than the sulfinate, due to lower charge density on the oxygens in the sulfonate. 
    more » « less