Current metal additive manufacturing (AM) systems suffer from limitations on the minimum feature sizes they can produce during part formation. The microscale selective laser sintering (μ-SLS) system addresses this drawback by enabling the production of parts with minimum feature resolutions of the order of a single micrometer. However, the production of microscale parts is challenging due to unwanted heat conduction within the nanoparticle powder bed. As a result, finite element (FE) thermal models have been developed to predict the evolution of temperature within the particle bed during laser sintering. These thermal models are not only computationally expensive but also must be integrated into an iterative model-based control framework to optimize the digital mask used to control the distribution of laser power. These limitations necessitate the development of a machine learning (ML) surrogate model to quickly and accurately predict the temperature evolution within the μ-SLS particle bed using minimal training data. The regression model presented in this work uses an “Element-by-Element” approach, where models are trained on individual finite elements to learn the relationship between thermal conditions experienced by each element at a given time-step and the element's temperature at the next time-step. An existing bed-scale FE thermal model of the μ-SLS system is used to generate element-by-element tabular training data for the ML model. A data-efficient artificial neural network (NN) is then trained to predict the temperature evolution of a 2D powder-bed over a 2 s sintering window with high accuracy.
more »
« less
Simulation and Property Characterization of Nanoparticle Thermal Conductivity for a Microscale Selective Laser Sintering System
Abstract Current Additive Manufacturing (AM) technologies are typically limited by the minimum feature sizes of the parts they can produce. This issue is addressed by the microscale selective laser sintering system (µ-SLS), which is capable of building parts with single micrometer resolutions. Despite the resolution of the system, the minimum feature sizes producible using the µ-SLS tool are limited by unwanted heat dissipation through the particle bed during the sintering process. To address this unwanted heat flow, a particle scale thermal model is needed to characterize the thermal conductivity of the nanoparticle bed during sintering and facilitate the prediction of heat affected zones (HAZ). This would allow for the optimization of process parameters and a reduction in error for the final part. This paper presents a method for the determination of the effective thermal conductivity of copper nanoparticle beds in a µ-SLS system using finite element simulations performed in ANSYS. A Phase Field Model (PFM) is used to track the geometric evolution of the particle groups within the particle bed during sintering. CAD models are extracted from the PFM output data at various timesteps, and steady state thermal simulations are performed on each particle group. The full simulation developed in this work is scalable to particle groups with variable sizes and geometric arrangements. The particle thermal model results from this work are used to calculate the thermal conductivity of the copper nanoparticles as a function of the density of the particle group.
more »
« less
- Award ID(s):
- 2141044
- NSF-PAR ID:
- 10391528
- Date Published:
- Journal Name:
- Journal of Heat Transfer
- ISSN:
- 0022-1481
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
One of the limitations of commercially available metal additive manufacturing (AM) processes is the minimum feature size most processes can achieve. A proposed solution to bridge this gap is microscale selective laser sintering (μ-SLS). The advent of this process creates a need for models which are able to predict the structural properties of sintered parts. While there are currently a number of good SLS models, the majority of these models predict sintering as a melting process which is accurate for microparticles. However, when particles tend to the nanoscale, sintering becomes a diffusion process dominated by grain boundary and surface diffusion between particles. As such, this paper presents an approach to model sintering by tracking the diffusion between nanoparticles on a bed scale. Phase field modeling (PFM) is used in this study to track the evolution of particles undergoing sintering. Changes in relative density are then calculated from the results of the PFM simulations. These results are compared to experimental data obtained from furnace heating done on dried copper nanoparticle inks, and the simulation constants are calibrated to match physical properties.more » « less
-
Abstract Nanoparticle heating due to laser irradiation is of great interest in electronic, aerospace, and biomedical applications. This paper presents a coupled electromagnetic-heat transfer model to predict the temperature distribution of multilayer copper nanoparticle packings on a glass substrate. It is shown that heat transfer within the nanoparticle packing is dominated by the interfacial thermal conductance between particles when the interfacial thermal conductance constant, GIC, is greater than 20 MW/m2K, but that for lower GIC values, thermal conduction through the air around the nanoparticles can also play a role in the overall heat transfer within the nanoparticle system. The coupled model is used to simulate heat transfer in a copper nanoparticle packing used in a typical microscale selective laser sintering (μ-SLS) process with an experimentally measured particle size distribution and layer thickness. The simulations predict that the nanoparticles will reach a temperature of 730 ± 3 K for a laser irradiation of 2.6 kW/cm2 and 1304 ± 23 K for a laser irradiation of 6 kW/cm2. These results are in good agreement with the experimentally observed laser-induced sintering and melting thresholds for copper nanoparticle packing on glass substrates.more » « less
-
One of the main challenges facing the expansion of Additive Manufacturing (AM) is the minimum feature sizes which these processes are able to achieve. Microscale Selective Laser Sintering (μ-SLS) is a novel Additive Manufacturing process created to meet this limitation by precisely laser sintering nanoparticles to give a better control over feature sizes. With the development of this new process, there is a concurrent need for models, which can predict the material properties of the sintering nanoparticles. To this end, this paper presents a novel simulation created to predict the electrical resistivity of sintered copper nanoparticles. Understanding the electrical resistivity of nanoparticles under sintering is useful for quantifying the rate of sintering and has applications such as predicting how the nanoparticles will fuse together when subjected to laser irradiation. Such a prediction allows for in situ corrections to be made to the sintering process to account for heat spreading beyond the intended laser irradiation targets. For these applications, it is important to ensure that the predictions of electrical resistivity from the simulations are accurate. This validation must be done against experimental data and since such experimental data does not currently exist, this paper also presents electrical resistivity data for the laser sintering of copper nanoparticles. In summary, this paper details the simulation methodology for predicting electrical resistivity of laser-sintered copper nanoparticles as well as validation of these simulations using electrical resistivity data from original sintering experiments. The key findings of this work are that the simulations can be used to predict electrical resistivity measurements for sintering of actual copper nanoparticles when the copper nanoparticles do not include other materials such as polymer coatings.more » « less
-
Sintering of nanoparticles to create films and patterns of functional materials is emerging as a key manufacturing process in applications like flexible electronics, solar cells and thin-film devices. Further, there is the emerging potential to use nanoparticle sintering to perform additive manufacturing as well. While the effect of nanoparticle size on sintering has been well studied, very little attention has been paid to the effect of nanoparticle shape on the evolution of sintering. This paper uses Molecular dynamics (MD) simulations to determine the influence of particle shape on shrinkage and neck growth for two common nanoparticle shape combinations, i.e., sphere-sphere and sphere-cylinder nanoparticles of different sizes. These sintering indicators are examined at two different temperature ramps. The results from this work show that depending on their relative sizes, degree of neck growth and shrinkage are both significantly affected by the nanoparticle shape. The possibility of using this phenomenon to control density and stresses during nanoparticle sintering are discussed.more » « less