More Like this

1. Mechanical Characterization of Compliant Cellular Robots. Part II: Active Strain

   https://doi.org/10.1115/1.4054613  

   Singh, Gaurav; Nawroj, Ahsan; Dollar, Aaron M. (April 2023, Journal of Mechanisms and Robotics)

   Abstract Modular active cell robots (MACROs) is a design approach in which a large number of linear actuators and passive compliant joints are assembled to create an active structure with a repeating unit cell. Such a mesh-like robotic structure can be actuated to achieve large deformation and shape-change. In this two-part paper, we use finite element analysis (FEA) to model the deformation behavior of different MACRO mesh topologies and evaluate their passive and active mechanical characteristics. In Part I, we presented the passive stiffness characteristics of different MACRO meshes. In this Part II of the paper, we investigate the active strain characteristics of planar MACRO meshes. Using FEA, we quantify and compare the strains generated for the specific choice of MACRO mesh topology and further for the specific choice of actuators actuated in that particular mesh. We simulate a series of actuation modes that are based on the angular orientation of the actuators within the mesh and show that such actuation modes result in deformation that is independent of the size of the mesh. We also show that there exists a subset of such actuation modes that spans the range of deformation behavior. Finally, we compare the actuation effort required to actuate different MACRO meshes and show that the actuation effort is related to the nodal connectivity of the mesh. 

   more » « less
2. Examine the Bending Stiffness of Generalized Kresling Modules for Robotic Manipulation

   https://doi.org/10.1115/DETC2020-22187  

   Kaufmann, Joshua; Li, Suyi (November 2020, ASME 2020 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference)

   null (Ed.)

   Via analytical modeling and experimental validation, this study examines the bending stiffness adaptation of bistable origami modules based on generalized Kresling pattern. These modules, which are the building blocks of an octopus-inspired robotic manipulator, can create a reconfigurable articulation via switching between their stable states. In this way, the manipulator can exhibit pseudo-linkage kinematics with lower control requirements and improved motion accuracy compared to completely soft manipulators. A key to achieving this reconfigurable articulation is that the underlying Kresling modules must show a sufficient difference in bending stiffness between their stable states. Therefore, this study aims to use both a nonlinear bar-hinge model and experimental testing to uncover the correlation between the module bending stiffness and the corresponding origami designs. The results show that the Kresling origami module can indeed exhibit a significant change in bending stiffness because of the reorientation of its triangular facets. That is, at one stable state, these facets align close to parallel to the longitudinal axis of the cylindrical-shaped module, so the module bending stiffness is relatively high and dominated by the facet stretching. However, at the other stable states, the triangular facets are orientated close to perpendicular to the longitudinal axis, so the bending stiffness is low and dominated by crease folding. The results of this study will provide the necessary design insights for constructing a fully functional manipulator with the desired articulation behavior. 

   more » « less
3. A Large Force Haptic Interface with Modular Linear Actuators

   https://doi.org/10.3390/act12070293  

   Jung, Yeongtae; Ramos, Joao (July 2023, Actuators)

   This paper presents a haptic interface with modular linear actuators that addresses the limitations of conventional devices based on rotary joints. The proposed haptic interface is composed of parallel linear actuators that provide high backdrivability and small inertia. The performance of the haptic interface is compared to those of conventional mechanisms in terms of force capability, reflected inertia, and structural stiffness. High stiffness, large range of motion, and high force capability, which are in trade-off relationships in traditional haptic interfaces, are achieved. The device can apply up to 83 N continuously, i.e., three-fold more than most haptic devices. The theoretical minimum haptic force density and stiffness of the proposed mechanism are 1.3 to 1.9 and 37 times those of the conventional mechanisms under similar conditions, respectively. The system is scalable because the structural stiffness depends on only the timing belt stiffness, whereas that of conventional haptic interfaces is inversely proportional to the cube of the structural length. The modular actuator enables changes in the degrees of freedom (DOFs) for different applications. The proposed haptic interface was tested through an interaction experiment in a virtual environment with virtual walls. 

   more » « less
4. A Variable Stiffness Robotic Arm Using Linearly Actuated Compliant Parallel Guided Mechanism

   https://doi.org/https://doi.org/10.1007/978-3-030-00365-4_5  

   Hu, R.; Venkiteswaran, V.; Su, H.-J. (January 2019, IFToMM Symposium on Mechanism Design for Robotics)

   This paper details the mechanical design and control of a human safety robotic arm with variable stiffness, starting from conceptual design to prototype. The mechanism designed is based on parallel guided beam with a roller slider actuated by a power screw and a DC motor with an encoder for position feedback. Unlike conventional robotic systems that control the stiffness in joints, this design introduces compliance to the robotic arm link itself. By controlling the slider position, the effective length of the link can be adjusted to provide the necessary stiffness change. A PID position controller is employed and the position accuracy is experimentally evaluated. The stiffness variation of the prototype is validated by experiments and FEA simulation. The overall stiffness change achieved is 20-fold. 

   more » « less
5. Characterization of a Class of Soft Bending Arms

   Olson, G.; Woronowicz, B.; Menguc, Y. (April 2019, IEEE International Conference on Soft Robotics)

   Bending permits soft arms to access a workspace that is not colinear with the initial arm axis; the size and shape of this space depends on the characteristics of the soft arm. Soft bending actuators and arms have developed for specific applications, but not characterized for the general relationship between design variables and performance. This paper defines a class of soft bending arms based on its design, considering the arm as a system constructed from many contracting actuators organized into segments. A modular segment design is presented, and seven variants of this design were constructed and tested for bend radius, bend direction, lateral stiffness and contraction. The variants isolate system parameters, in this case, arm radius and number of actuators within a given segment, to quantify how these parameters affect performance. A trade-off was found between lateral stiffness and bend radius, which can be controlled by altering the arm radius or the number of actuators. Bend direction was found to be coupled to both bend radius and arm load. Finally, a three-segment arm following a bio-inspired design is presented to demonstrate how the experimental results apply to soft robot system design. 

   more » « less