An official website of the United States government
This study investigates the programmable strain sensing capability, auxetic behaviour, and failure modes of 3D-printed, self-monitoring auxetic lattices fabricated from in-house engineered polyetheretherketone (PEEK) reinforced with multi-walled carbon nanotubes (MWCNTs). A skeletally-parametrized geometric modelling framework, combining Voronoi tessellation with 2D wallpaper symmetries, is used to systematically explore a vast range of non-predetermined topologies beyond traditional lattice designs. A representative set of these architectures is realized via fused filament fabrication, and multiscale characterization—including macroscale tensile testing and microstructural analysis—demonstrates tuneable multifunctional performance as a function of MWCNT content and unit cell topology. Real-time resistance measurements track deformation, damage initiation, and progression, with the sensitivity factor increasing from below 1 in the elastic regime (strain sensitivity) to as high as 80 for PEEK/MWCNT at 6 wt.% under inelastic deformation (damage sensitivity). Implicit architecture-topology tailoring further allows fine-tuning of mechanical properties, achieving stiffness values ranging from 9 MPa to 63 MPa and negative Poisson’s ratios between –0.63 and –0.17 using ~3 wt.% MWCNT at a relative density of 25%. Furthermore, a novel piezoresistive finite element model, implemented in Abaqus via a user-defined subroutine, accurately captures the electromechanical response up to the onset of ligament failure, offering predictive capability. These results demonstrate how architecture-topology tuning can be leveraged to customise strain sensitivity and failure modes, enabling the development of multifunctional piezoresistive lattice composites for applications such as smart orthopaedic implants, aerospace skins, and impact-tolerant systems.
more »
« less
Behavior of 3D Printed Stretchable Structured Sensors
Piezoresistive structures inspired by serpentines, auxetic, and kirigami arrangements have demonstrated good flexibility and sensitivity under tension. Piezoresistive structures display optimal performance when the characteristics entail reliable stretchability and repeatability. These structures can be implemented as wearable sensors by compressing and elongating the conductive nanocomposites to vary the flow of electrons and to provide resistance change. To guarantee the reliability of these structures for strain sensing, it is important that the resistance change in these structures remains constant under repeated loads. In this study, the performance of different piezoresistive structures under cyclic tensile load is investigated and compared. Based on the performance of different types of structures, novel hybrid structures have been also proposed to design for both high stretchability and sensitivity of piezoresistive sensors. All the structures were tested with position limits rather than a fixed force to avoid permanent deformation. First, small position limits were used to determine Young’s Modulus, then a 10-cycle tensile test with larger position limits was used to further study the electromechanical behavior of different piezoresistive structures under larger deformation and repetition. Finally, the gage factor was derived for all the studied structures, and they were re-categorized based on properties’ similarities.
more »
« less
- Award ID(s):
- 2051066
- PAR ID:
- 10409808
- Date Published:
- Journal Name:
- Electronics
- Volume:
- 12
- Issue:
- 1
- ISSN:
- 2079-9292
- Page Range / eLocation ID:
- 18
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Development of highly stretchable and sensitive soft strain sensors is of great importance for broad applications in artificial intelligence, wearable devices, and soft robotics, but it proved to be a profound challenge to integrate the two seemingly opposite properties of high stretchability and sensitivity into a single material. Herein, we designed and synthesized a new fully polymeric conductive hydrogel with an interpenetrating polymer network (IPN) structure made of conductive PEDOT:PSS polymers and zwitterionic poly(HEAA- co -SBAA) polymers to achieve a combination of high mechanical, biocompatible, and sensing properties. The presence of hydrogen bonding, electrostatic interactions, and IPN structures enabled poly(HEAA- co -SBAA)/PEDOT:PSS hydrogels to achieve an ultra-high stretchability of 4000–5000%, a tensile strength of ∼0.5 MPa, a rapid mechanical recovery of 70–80% within 5 min, fast self-healing in 3 min, and a strong surface adhesion of ∼1700 J m −2 on different hard and soft substrates. Moreover, the integration of zwitterionic polySBAA and conductive PEDOT:PSS facilitated charge transfer via optimal conductive pathways. Due to the unique combination of superior stretchable, self-adhesive, and conductive properties, the hydrogels were further designed into strain sensors with high sensing stability and robustness for rapidly and accurately detecting subtle strain- and pressure-induced deformation and human motions. Moreover, an in-house mechanosensing platform provides a new tool to real-time explore the changes and relationship between network structures, tensile stress, and electronic resistance. This new fully polymeric hydrogel strain sensor, without any conductive fillers, holds great promise for broad human-machine interface applications.more » « less
-
Monitoring posture and movement accurately and efficiently is essential for both physical therapy and athletic training evaluation and interventions. Motion Tape (MT), a self-adhesive wearable skin-strain sensor made of piezoresistive graphene nanosheets (GNS), has demonstrated promise in capturing low back posture and movements. However, to address some of its limitations, this work explores alternative materials by replacing GNS with multi-walled carbon nanotubes (MWCNT). This study aimed to characterize the electromechanical properties of MWCNT-based MT. Cyclic load tests for different peak tensile strains ranging from 1% to 10% were performed on MWCNT-MT made with an aqueous ink of 2% MWCNT. Additional tests to examine load rate sensitivity and fatigue were also conducted. After characterizing the properties of MWCNT-MT, a human subject study with 10 participants was designed to test its ability to capture different postures and movements. Sets of six sensors were made from each material (GNS and MWCNT) and applied in pairs at three levels along each side of the lumbar spine. To record movement of the lower back, all participants performed forward flexion, left and right bending, and left and right rotation movements. The results showed that MWCNT-MT exceeded GNS-MT with respect to consistency of signal stability even when strain limits were surpassed. In addition, both types of MT could assess lower back movements.more » « less
-
This paper presents a recent investigation into the electromechanical behavior of thermally reduced graphene oxide (rGO) as a strain sensor undergoing repeated large mechanical strains up to 20.72%, with electrical signal output measurement in multiple directions relative to the applied strain. Strain is one the most basic and most common stimuli sensed. rGO can be synthesized from abundant materials, can survive exposure to large strains (up to 20.72%), can be synthesized directly on structures with relative ease, and provides high sensitivity, with gauge factors up to 200 regularly reported. In this investigation, a suspension of graphene oxide flakes was deposited onto Polydimethylsiloxane (PDMS) substrates and thermally reduced to create macroscopic rGO-strain sensors. Electrical resistance parallel to the direction of applied tension (x^) demonstrated linear behavior (similar to the piezoresistive behavior of solid materials under strain) up to strains around 7.5%, beyond which nonlinear resistive behavior (similar to percolative electrical behavior) was observed. Cyclic tensile testing results suggested that some residual micro-cracks remained in place after relaxation from the first cycle of tensile loading. A linear fit across the range of strains investigated produced a gauge factor of 91.50(Ω/Ω)/(m/m), though it was observed that the behavior at high strains was clearly nonlinear. Hysteresis testing showed high consistency in the electromechanical response of the sensor between loading and unloading within cycles as well as increased consistency in the pattern of the response between different cycles starting from cycle 2.more » « less
-
Abstract Despite the growing interest in flexible electronics and wearable sensors, research in piezoresistive polymer nanocomposites has stagnated in consideration of the polymer matrices, particularly in additive manufacturing (AM) applications. This research focuses on using a low‐molecular isoprene rubber (IR) as a matrix filled with carbonaceous nanoparticles conductive carbon black (CCB) and carbon nanotubes (CNT) to create piezoresistive sensors printed via direct ink writing (DIW). Using IR as a matrix not only provides an avenue for an alternate sensor matrix, but also offers a distinct advantage for retrofit sensor applications to other diene rubber substrates due to both the feedstock and substrate possessing the same vulcanization mechanism. Thereby, the rheological, mechanical, and piezoresistive properties of the IR nanocomposites are fully investigated, with emphasis on non‐ambient conditions (temperature and durability). In this work it is shown that while CCB exhibits a lower gauge factor (between 1.5 and 8) across all strain rates, strain ranges, and temperatures when compared to CNT compounds (gauge factors between 1.5 and 260), CCB compounds possess better linearity, less temperature deviation, and overall better performance under cyclic loading conditions. This is followed by demonstrations for real‐world applications, including the direct‐to‐product printing of a CCB strain gauge on a chloroprene rubber substrate. HighlightsAM via DIW of piezoresistive isoprene sensors filled with conductive CB and multi‐wall carbon nanotubes.Printed samples capable of achieving tensile strength >3.5 MPa.CB sensors showed less sensitivity, but better durability and repeatability compared to carbon nanotube filled sensors.Piezoresistive isoprene strain gauge printed on chloroprene substrate with direct adhesion.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/electronics12010018
