An official website of the United States government
In the presence of gravity, the micrometer-sized charged dust particles in a complex (dusty) plasma are compressed into thin layers. However, under the microgravity conditions of the Plasma Kristall-4 (PK-4) experiment on the International Space Station (ISS), the particles fill the plasma, allowing us to investigate the properties of a three-dimensional multi-particle system. This paper examines the change in the spatial ordering and thermal state of the particle system created when dust particles are stopped by periodic oscillations of the electric field, known as polarity switching, in a dc glow discharge plasma. Data from the ISS are compared against experiments performed using a ground-based reference version of PK-4 and numerical simulations. Initial results show substantive differences in the velocity distribution functions between experiments on the ground and in microgravity. There are also differences in the motion of the dust cloud; in microgravity, there is an expansion of the dust cloud at the application of polarity switching, which is not seen in the ground-based experiments. It is proposed that the dust cloud in microgravity gains thermal energy at the application of polarity switching due to this expansion. Simulation results suggest that this may be due to a modification in the effective screening length at the onset of polarity switching, which allows the dust particles to utilize energy from the potential energy in the configuration of the dust cloud. Experimental measurements and simulations show that an extended time (much greater than the Epstein drag decay) is required to dissipate this energy.
more »
« less
Coulomb expansion of a thin dust cloud observed experimentally under afterglow plasma conditions
The Coulomb expansion of a thin cloud of charged dust particles was observed experimentally, in a plasma afterglow. This expansion occurs due to mutual repulsion among positively charged dust particles, after electrons and ions have escaped the chamber volume. In the experiment, a two-dimensional cloud of dust particles was initially levitated in a glow-discharge plasma. The power was then switched off to produce afterglow conditions. The subsequent fall of the dust cloud was slowed by reversing the electric force, to an upward direction, allowing an extended observation. At early time, measurements of the Coulomb expansion in the horizontal direction are found to be accurately modeled by the equation of state for a uniformly charged thin disk. Finally, bouncing from the lower electrode was found to be avoided by lowering the impact velocity <100 mm/s.
more »
« less
- Award ID(s):
- 1740379
- PAR ID:
- 10410946
- Date Published:
- Journal Name:
- Physics of Plasmas
- Volume:
- 29
- Issue:
- 11
- ISSN:
- 1070-664X
- Page Range / eLocation ID:
- 113705
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract A dust particle immersed in a glow-discharge plasma has long been known to have a charge that isnegative, while the plasma is powered. However, in the afterglow, following the stopping of the plasma power, a largepositivecharge can collect on the particle, as was shown recently for particles in a cathodic sheath. While that outcome of positive charging in the afterglow may be common, an experimental discovery reported here reveals that the opposite outcome is also possible: a particle can develop anegativecharge in the afterglow, if the plasma had previously been operated with a modulated power. Before stopping the plasma power off altogether, in a run with power modulated at a low duty cycle of 4.5 , the particle’s residual charge was negative, but it was positive in a control run without modulation. This result points to a way of controlling the charge of dust particles in a decaying plasma, which can be useful for mitigating defects in semiconductor manufacturing.more » « less
-
Abstract A method is demonstrated for controlling the charge of a dust particle in a plasma afterglow, allowing a wider range of outcomes than an earlier method. As in the earlier method, the dust particles are located near an electrode that has a DC voltage during the afterglow. Here, that DC voltage is switched to a positive value at a specified delay time, instead of maintaining a constant negative voltage as in the earlier method. Adjusting the timing of this switching allows one to control the residual charge gradually over a wide range that includes both negative and positive values of charge. For comparison, only positive residual charges were attained in the earlier method. We were able to adjust the residual charge from about −2000 eto +10 000 e, for our experimental parameters (8.35 µm particles, 8 mTorr argon pressure, and a DC voltage that was switched from −150 V to +125 V within the first two milliseconds of the afterglow). The plasma conditions near the dust particles changed from ion-rich to electron-rich, when the electrode was switched from cathodic to anodic. Making this change at a specified time, as the electrons and ions decay in the afterglow, provides this control capability. These results also give insight into the time development of a dust particle’s charge in the afterglow, on a sub-millisecond time scale.more » « less
-
Dust grains have been used as minimally invasive probes to determine plasma parameters including the plasma density, temperature, and electric field in a plasma discharge. However, the dust grains in a plasma generate local potential disturbances due to the collection of charge and the subsequent electrostatic interactions between the dust and charged plasma particles. Dust grains in close proximity to one another exhibit interesting non-reciprocal interactions and self-organize into structures such as one-dimensional filamentary chains, two-dimensional “zigzags,” and three-dimensional helices, among others. The formation of these structures suggests that although the dust grains may be less invasive than traditional plasma probes, the disturbance to the local plasma environment introduced by dust grains is non-trivial. Commonly used analytic forms of the electric potential describing complex plasmas have failed to resolve the near-dust region, and as a result are insufficient to provide insight about the formation of complex dust structures. Here, we use an N-body simulation to compute the electric potential from ion densities near various dust grain configurations. We provide an alternative description to the standard analytic model for the electric potential of dust and ion wakes based on a Gaussian shaped cloud of ions. The electric potential obtained from simulations is used to identify minimum energy configurations for two and three dust grains. It is further demonstrated that the minimum potential region identified for N dust grains and their associated ion wakes does not predict the minimum-energy configuration of N + 1 dust grains.more » « less
-
Abstract Particle contamination due to plasma processing motivates the design of a method of electrically lifting particles in a time interval after a plasma’s power is turned off. Small solid dust particles have electric charges that are not frozen until a late stage of the plasma afterglow. Beyond that time, before they fall to a surface below and cause defects, particles can be lifted in a controlled manner by applying an appropriate direct-current (DC) electric field, as we demonstrate experimentally. A few milliseconds after an argon plasma’s capacitively coupled radio-frequency power is switched off, a vertical DC electric field is applied. Thereafter, video imaging shows that the falling of the particles is slowed or stopped altogether, depending on the magnitude of the upward electric force.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1063/5.0112680
