An official website of the United States government
Abstract Defects in crosslinked networks have a negative effect on mechanical and functional properties. In this study, an epoxy resin diglycidyl ether of bisphenol A crosslinked by a hardener 4,4-diaminodiphenyl methane with various cyclic topologies was simulated to find correlations between the mechanical/shape memory properties (i.e. glassy/rubbery elastic modulus, shape recovery ratio, and recovery stress) and cyclic topologies (i.e. number of total loops, number of defective loops (DLs), etc). The effect of cyclic topology on shape memory properties was more significant than its effect on mechanical properties, altering recovery stress by more than 25% on average. After analyzing several topological fingerprints such as total number of loops, number of DLs, and number of higher order loops, we found that the effect of cyclic topology on the mechanical/shape memory properties of the systems can be best understood by the fraction of hardeners reacted with four distinct epoxy molecules (tetra-distinctly-reacted (TDR) hardeners). By increasing the number of TDR hardeners, the network is closer to ideal, resulting in an increase in the number of higher order loops and a reduction in the number of DLs, which in turn leads to an increase in rubbery elastic modulus and shape recovery ratio to a lesser degree, but a substantial increase in recovery stress. These results suggest that utilization of experimental techniques such as semibatch monomer addition, which leads to a more expanded and defect-free network, can result in a simultaneous increase in both shape recovery ratio and recovery stress in thermoset shape memory polymers (TSMPs). Moreover, topology alteration can be used to synthesize TSMPs with improved recovery stress without significantly increasing their stiffness.
more »
« less
Mechanical rigidity of a shape-memory metal–organic framework increases by crystal downsizing
Soft porous nanocrystals with a pronounced shape-memory effect exhibit two- to three-fold increase in elastic modulus compared to the microcrystalline counterpart as determined by atomic force microscopy nanoindentation. The increase in rigidity is consistent with the known shape-memory effect displayed by the framework solid at the nanoscale. Crystal downsizing can offer new avenues for tailoring the mechanical properties of metal–organic frameworks.
more »
« less
- Award ID(s):
- 1757548
- PAR ID:
- 10415413
- Date Published:
- Journal Name:
- Chemical Communications
- Volume:
- 57
- Issue:
- 1
- ISSN:
- 1359-7345
- Page Range / eLocation ID:
- 89 to 92
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Here we report a systematic research on effects of Fe and Cu upon properties relevant for the magnetic shape memory effect of Ni–Mn–Ga ferromagnetic shape memory alloys. Fe and Cu were identified as elements with potential synergism to increase the martensite transformation temperature of Ni–Mn–Ga magnetic shape memory (MSM) alloys. Eighteen Ni–Mn–Ga–Fe–Cu alloys with different systematic trends in substituting the ternary elements with Cu and Fe have been investigated. We found a method to describe the effectiveness of Ni, Mn, and Cu upon raising the martensitic transformation temperature, lowering the saturation magnetization, and varying the Curie temperature. We find the martensite transformation temperature most influenced by the Ni content, followed by Mn, with a smaller effect of Cu. The saturation magnetization decreases with similar coefficients for Mn and Cu alloying. The Curie temperature monotonously decreases with Mn, but not Cu. The 10M martensite structure is stable for the composition Ni46.5Mn25?XGa25-X-YFe3.5CuY with X and Y range of 0–5.7, and 0.8–3.0. Used in combination with the total e/a, the elemental e/a-ratio gives some insight into the complex behavior of quinary MSM alloys and is a useful method of analyzing MSM alloys for improved functional properties.more » « less
-
Incorporating thermoplastic materials with shape memory properties into the fused filament fabrication process enables what is commonly referred to as 4D printing. When the blends are composed of one or more materials with inherent shape memory properties, the tailoring of critical parameters such as shape recovery temperature can be realized. Previous work by our group demonstrated the creation of shape memory polymer blends where one component was elastomeric. The following work entails the development and characterization of rigid polyester blends that are biocompatible and biodegradable in addition to having shape memory properties. Dynamic mechanical analysis (DMA) was used to determine the critical deformation and recovery temperatures. The effect of print raster patterns on the DMA results was also evaluated. Micro- tensile testing was used to characterize the physical properties of the materials at elevated temperatures. Finally, scanning electron microanalysis was used to examine the fracture surfaces of spent tensile specimens.more » « less
-
Abstract Tension programmed shape memory polymer (SMP) fibers have been used as sutures for closing wide‐opened cracks per the close‐then‐heal strategy. However, the composite may be subjected to compression loading during service. These compression loads can reduce the amount of recoverable strain in these pre‐tensioned fibers, limiting their ability to close cracks. The purpose of this study is to investigate the effect of in‐service compression loading on the shape memory effect (SME) of composites consisting of SMP fiber and SMP matrix. To this end, pre‐stretched shape memory Polyethylene Terephthalate (PET) fibers were embedded into a shape memory vitrimer to obtain composite samples with different fiber volume fractions. The SME of both the PET fiber and the vitrimer was investigated. The effect of compression load on the SME of the composite was studied. It is found that, uniaxial compression on the composite along the fiber direction significantly reduced the shrinking ability of the embedded pre‐tensioned SMP fibers. Hence, this is a factor that needs to be considered when designing such types of self‐healing composites.more » « less
-
Abstract Emerging transformable lattice structures provide promising paradigms to reversibly switch lattice configurations, thereby enabling their properties to be tuned on demand. The existing transformation mechanisms are limited to nonfracture deformation, such as origami, instability, shape memory, and liquid crystallinity. In this study, we present a class of transformable lattice structures enabled by fracture and shape-memory-assisted healing. The lattice structures are additively manufactured with a molecularly designed photopolymer capable of both fracture healing and shape memory. We show that 3D-architected lattice structures with various volume fractions can heal fractures and fully restore stiffness and strength over two to ten healing cycles. In addition, coupled with the shape-memory effect, the lattice structures can recover fracture-associated distortion and then heal fracture interfaces, thereby enabling healing of lattice wing damages, mode-I fractures, dent-induced crashes, and foreign-object impacts. Moreover, by harnessing the coupling of fracture and shape-memory-assisted healing, we demonstrate reversible configuration transformations of lattice structures to enable switching among property states of different stiffnesses, vibration transmittances, and acoustic absorptions. These healable, memorizable, and transformable lattice structures may find broad applications in next-generation aircraft panels, automobile frames, body armor, impact mitigators, vibration dampers, and acoustic modulators.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/D0CC05684G
