Carbon nanotube (CNT)‐reinforced polymer fibers have broad applications in electrical, thermal, optical, and smart applications. The key for mechanically robust fibers is the precise microstructural control of these CNTs, including their location, dispersion, and orientation. A new methodology is presented here that combines dry‐jet‐wet spinning and forced assembly for scalable fabrication of fiber composites, consisting of alternating layers of polyacrylonitrile (PAN) and CNT/PAN. The thickness of each layer is controlled during the multiplication process, with resolutions down to the nanometer scale. The introduction of alternating layers facilitates the quality of CNT dispersion due to nanoscale confinement, and at the same time, enhances their orientation due to shear stress generated at each layer interface. In a demonstration example, with 0.5 wt% CNTs loading and the inclusion of 170 nm thick layers, a composite fiber shows a significant mechanical enhancement, namely, a 46.4% increase in modulus and a 39.5% increase in strength compared to a pure PAN fiber. Beyond mechanical reinforcement, the presented fabrication method is expected to have enormous potential for scalable fabrication of polymer nanocomposites with complex structural features for versatile applications.
This content will become publicly available on May 10, 2024
Nanocomposites containing nanoscale materials offer exciting opportunities to encode nanoscale features into macroscale dimensions, which produces unprecedented impact in material design and application. However, conventional methods cannot process nanocomposites with a high particle loading, as well as nanocomposites with the ability to be tailored at multiple scales. A composite architected mesoscale process strategy that brings particle loading nanoscale materials combined with multiscale features including nanoscale manipulation, mesoscale architecture, and macroscale formation to create spatially programmed nanocomposites with high particle loading and multiscale tailorability is reported. The process features a low‐shrinking (<10%) “green‐to‐brown” transformation, making a near‐geometric replica of the 3D design to produce a “brown” part with full nanomaterials to allow further matrix infill. This demonstration includes additively manufactured carbon nanocomposites containing carbon nanotubes (CNTs) and thermoset epoxy, leading to multiscale CNTs tailorability, performance improvement, and 3D complex geometry feasibility. The process can produce nanomaterial‐assembled architectures with 3D geometry and multiscale features and can incorporate a wide range of matrix materials, such as polymers, metals, and ceramics, to fabricate nanocomposites for new device structures and applications.
more » « less- NSF-PAR ID:
- 10418911
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Materials
- Volume:
- 35
- Issue:
- 38
- ISSN:
- 0935-9648
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Mesoporous inorganic particles and hollow spheres are of increasing interest for a broad range of applications, but synthesis approaches are typically material specific, complex, or lack control over desired structures. Here it is reported how combining mesoscale block copolymer (BCP) directed inorganic materials self‐assembly and macroscale spinodal decomposition can be employed in multicomponent BCP/hydrophilic inorganic precursor blends with homopolymers to prepare mesoporous inorganic particles with controlled meso‐ and macrostructures. The homogeneous multicomponent blend solution undergoes dual phase separation upon solvent evaporation. Microphase‐separated (BCP/inorganic precursor)‐domains are confined within the macrophase‐separated majority homopolymer matrix, being self‐organized toward particle shapes that minimize the total interfacial area/energy. The pore orientation and particle shape (solid spheres, oblate ellipsoids, hollow spheres) are tailored by changing the kind of homopolymer matrix and associated enthalpic interactions. Furthermore, the sizes of particle and hollow inner cavity are tailored by changing the relative amount of homopolymer matrix and the rates of solvent evaporation. Pyrolysis yields discrete mesoporous inorganic particles and hollow spheres. The present approach enables a high degree of control over pore structure, orientation, and size (15–44 nm), particle shape, particle size (0.6–3 µm), inner cavity size (120–700 nm), and chemical composition (e.g., aluminosilicates, carbon, and metal oxides).
-
Photonic balls are spheres tens of micrometers in diameter containing assemblies of nanoparticles or nanopores with a spacing comparable to the wavelength of light. When these nanoscale features are disordered, but still correlated, the photonic balls can show structural color with low angle-dependence. Their colors, combined with the ability to add them to a liquid formulation, make photonic balls a promising new type of pigment particle for paints, coatings, and other applications. However, it is challenging to predict the color of materials made from photonic balls because the sphere geometry and multiple scattering must be accounted for. To address these challenges, we develop a multiscale modeling approach involving Monte Carlo simulations of multiple scattering at two different scales: we simulate multiple scattering and absorption within a photonic ball and then use the results to simulate multiple scattering and absorption in a film of photonic balls. After validating against experimental spectra, we use the model to show that films of photonic balls scatter light in fundamentally different ways than do homogeneous films of nanopores or nanoparticles, because of their increased surface area and refraction at the interfaces of the balls. Both effects tend to sharply reduce color saturation relative to a homogeneous nanostructured film. We show that saturated colors can be achieved by placing an absorber directly in the photonic balls and mitigating surface roughness. With these design rules, we show that photonic-ball films have an advantage over homogeneous nanostructured films: their colors are even less dependent on the angle.more » « less
-
Abstract Nature provides us with a large number of functional material systems consisting of hierarchical structures, where significant variations in dimensions are present. Such hierarchical structures are difficult to build by traditional manufacturing processes due to manufacturing limitations. Nowadays, three-dimensional (3D) objects with complex structures can be built by gradually accumulating in a layer-based additive manufacturing (AM); however, the hierarchical structure measured from macroscale to nanoscale sizes still raises significant challenges to the AM processes, whose manufacturing capability is intrinsically specified within a certain scope. It is desired to develop a multiscale AM process to narrow this gap between scales of feature in hierarchical structures. This research aims to investigate an integration approach to fabricating hierarchical objects that have macro-, micro-, and nano-scales features in an object. Firstly, the process setup and the integrated process of two-photon polymerization (TPP), immersed surface accumulation (ISA), and mask image projection-based stereolithography (MIP-SL) were introduced to address the multiscale fabrication challenge. Then, special hierarchical design and process planning toward integrating multiple printing processes are demonstrated. Lastly, we present two test cases built by our hierarchical printing method to validate the feasibility and efficiency of the proposed multiscale hierarchical printing approach. The results demonstrated the capability of the developed multiscale 3D printing process and showed its future potential in various novel applications, such as optics, microfluidics, cell culture, as well as interface technology.more » « less
-
more » « less
Abstract Recapitulation of multiscale structure–function properties of cells, cell‐secreted extracellular matrix, and 3D architecture of natural tissues is central to engineering biomimetic tissue substitutes. Toward achieving biomimicry, a variety of biofabrication processes have been developed, which can be broadly classified into five categories—fiber and fabric formation, additive manufacturing, surface modification, remote fields, and other notable processes—each with specific advantages and limitations. The majority of biofabrication literature has focused on using a single process at a time, which often limits the range of tissues that could be created with relevant features that span nano to macro scales. With multiscale biomimicry as the goal, development of hybrid biofabrication strategies that synergistically unite two or more processes to complement each other's strengths and limitations has been steadily increasing. This work discusses recent literature in this domain and attempts to equip the reader with the understanding of selecting appropriate processes that can harmonize toward creating engineered tissues with appropriate multiscale structure–function properties. Opportunities related to various hybridization schemes and a future outlook on scale‐up biofabrication have also been discussed.
This article is categorized under:
Nanotechnology Approaches to Biology > Nanoscale Systems in Biology
Implantable Materials and Surgical Technologies > Nanotechnology in Tissue Repair and Replacement
