This paper explores the use of reconfigurable intelligent surfaces (RIS) in mitigating cross-system interference in spectrum sharing and secure wireless applications. Unlike conventional RIS that can only adjust the phase of the incoming signal and essentially reflect all impinging energy, or active RIS, which also amplify the reflected signal at the cost of significantly higher complexity, noise, and power consumption, an absorptive RIS (ARIS) is considered. An ARIS can in principle modify both the phase and modulus of the impinging signal by absorbing a portion of the signal energy, providing a compromise between its conventional and active counterparts in terms of complexity, power consumption, and degrees of freedom (DoFs). We first use a toy example to illustrate the benefit of ARIS, and then we consider three applications: 1) spectral coexistence of radar and communication systems, where a convex optimization problem is formulated to minimize the Frobenius norm of the channel matrix from the communication base station to the radar receiver; 2) spectrum sharing in device-to-device (D2D) communications, where a max-min scheme that maximizes the worst-case signal-to-interference-plus-noise ratio (SINR) among the D2D links is developed and then solved via fractional programming; 3) physical layer security of a downlink communication system, where the secrecy rate is maximized and the resulting nonconvex problem is solved by a fractional programming algorithm together with a sequential convex relaxation procedure. Numerical results are then presented to show the significant benefit of ARIS in these applications.
more »
« less
Clutter Suppression for Target Detection Using Hybrid Reconfigurable Intelligent Surfaces
Reconfigurable intelligent surface (RIS) technology is a promising approach being considered for future wireless communications due to its ability to control signal propagation with low-cost elements. This paper explores the use of an RIS for clutter mitigation and target detection in radar systems. Unlike conventional reflect-only RIS, which can only adjust the phase of the reflected signal, or active RIS, which can also amplify the reflected signal at the cost of significantly higher complexity, noise, and power consumption, we exploit hybrid RIS that can configure both the phase and modulus of the impinging signal by absorbing part of the signal energy. Such RIS can be considered as a compromise solution between conventional reflect-only and active RIS in terms of complexity, power consumption, and degrees of freedoms (DoFs). We consider two clutter suppression scenarios: with and without knowledge of the target range cell. The RIS design is formulated by minimizing the received clutter echo energy when there is no information regarding the potential target range cell. This turns out to be a convex problem and can be efficiently solved. On the other hand, when target range cell information is available, we maximize the received signal-to-noise-plus-interference ratio (SINR). The resulting non-convex optimization problem is solved through fractional programming algorithms. Numerical results are presented to demonstrate the performance of the proposed hybrid RIS in comparison with conventional RIS in clutter suppression for target detection.
more »
« less
- PAR ID:
- 10430191
- Date Published:
- Journal Name:
- 2023 IEEE Radar Conference (RadarConf23)
- Page Range / eLocation ID:
- 1 to 5
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This paper explores reconfigurable intelligent surfaces (RIS) for mitigating cross-system interference in spectrum sharing applications. Unlike conventional reflect-only RIS that can only adjust the phase of the incoming signal, a hybrid RIS is considered that can configure the phase and modulus of the impinging signal by absorbing part of the signal energy. We investigate two spectrum sharing scenarios: (1) Spectral coexistence of radar and communication systems, where a convex optimization problem is formulated to minimize the Frobenius norm of the channel matrix from the communication base station to the radar receiver, and (2) Spectrum sharing in device-to-device (D2D) communications, where a max-min scheme that optimizes the worst-case signal-to-interference-plus-noise ratio (SINR) among the D2D links is formulated, and then solved through fractional programming. Numerical results show that with a sufficient number of elements, the hybrid RIS can in many cases completely eliminate the interference, unlike a conventional non-absorptive RIS.more » « less
-
This paper explores the use of reconfigurable intelligent surfaces (RISs) for moving target detection in multi-input multi-output (MIMO) radar. Unlike previous related works that ignore the propa-gation delay difference between the direct path and the RIS-reflected path, we examine the detection problem in RIS-assisted MIMO radar by taking into account the effect of asynchronous propagation. Specifically, we first develop a general signal model for RIS-aided MIMO radar with multiple asynchronous RISs and arbitrary wave-forms. Next, we formulate the RIS design problem by maximizing the overall received signal energy. The resulting optimization problem is non-convex, which is solved with semidefinite relaxation (SDR) techniques. A coherent detector is introduced for target detection. Finally, numerical results are presented to demonstrate the performance of the RIS-aided MIMO radar in comparison with the conventional MIMO radar.more » « less
-
In this paper, we develop efficient methods for devising lower complexity receivers that can achieve performance close to the full complexity receivers for passive/active multiple-input multiple-output (MIMO) radar. The method employed eliminates some parts of the test statistic to lower either hardware or software complexity. For the case of spatially uncorrelated reflection coefficients and spatially white clutter-plus-noise, the test statistic requires the computation of a set of matched filters, each matched to a signal from a different transmitter. In this case, our method is equivalent to selecting a specific set of transmitters to provide optimum performance. In the more general case of correlated clutter-plus-noise and reflection coefficients, then the test statistic requires the computation of a larger set of matched filters. These matched filters correlate the clutter-plus-noise free signal received at one receive antenna due to the signal transmitted from some transmit antenna and the signal received at another receive antenna. In the more general case, our algorithm picks the best of these matched filters to implement when the total number of these matched filters one can implement is limited.more » « less
-
The problem of decomposing a signal into components of different structures arises in many applications of signal processing and machine learning. In this paper, we study such a signal demixing problem for airborne radar systems, where the received signal consists of contributions from targets, jammers, and clutter. We promote the structures of the target and jammer components by designing two atomic norms, while we model the clutter signal as lying in a known subspace. This allows the formulation of a convex optimization that is able to separate these components, enabling the localization of targets and jammers as well as the supression of the clutter. Simulations show the superior performance of our approach compared to the classical space-time adaptive processing (STAP) technique.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.1109/RadarConf2351548.2023.10149583
